Today on this 2010 Toyota Prius we are going to install part number 24847 from Draw-Tite. This also applies to part number 60263 from Hidden Hitch. On the passenger side we are going to have to lower the exhaust. We are going to take down this bracket here with those two bolts. What will happen is the hitch will go up and the bracket will go on top of the hitch when we are done. :21
We are just going to leave it all just like that. Our hitch is going to fit between the frame and the bracket. Go back to the driver side and take down the driver bracket. The hitch is going to mount up on the frame here. Right now it is covered up by the tie down bracket so this bracket is going to come down with the bolts so that is what we are going to do on this side. :48
There is a lot of plastic underneath this vehicle here, and actually this is going to stay up there. What is going to happen is we are going to put the hitch up in an angle and inside. Then we can start installing the hitch. We will go ahead and put our hitch up into place. We will start by ing the drivers side into the plastic. We are just going to let it hang there. Then we will work it on the other side, back over the exhaust hanger on the passenger side. We will put it all together just like that. We will go back over to the drivers side and get that started. The trick is to get the bolts in here is to use and extension. We actually put a little nut inside of the socket here to hold the bolt up a little higher than normal. We will go ahead and just thread it up into place. 1:44
All right now that we have all the bolts started we will go ahead and snug them all down. Then we will torque them as specified in the instructions. All right, and there you have it for part number 24847 from Draw-Tite.
Trailer Hitch Installation - 2013 Toyota Prius - Curt
Today on our 2013 Toyota Prius, we're going to install Curt hitch part number C11276. This is what our hitch looks like on our vehicle. Here are a few measurements to help you select some accessories for your hitch, such as a ball mount, bicycle rack, or cargo carrier. From the center hole up to the edge of the bumper is approximately 2", and from the top of the opening for the receiver to the ground is approximately 11-1/2". Now let's go ahead and install our hitch. To begin with, you'll need to locate the four bolts that need to be removed from the factory.
Trailer Hitch Installation - 2013 Toyota Prius - Hidden Hitch
Today on this 2013 Toyota Prius, we'll be installing Hidden Hitch, part number 60263. And this is what the hitch looks like installed. Now here are some measurements to help you select some accessories for your hitch, such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin hole to the edge of the bumper is approximately 1-1/2". From the top of the receiver opening to the ground is approximately 11-1/4". Now let's go ahead and install our hitch.
Trailer Hitch Installation - 2013 Toyota Prius - Draw-Tite
Today on this 2013 Toyota Prius we'll be installing a Draw-Tite Hitch, part number 24847. This is what the hitch looks like installed. Here's some measurements to help you select some accessories for your hitch such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the edge of the bumper is approximately one and a half inches. From the top of the receiver opening to the ground is approximately 11 1/4 inches.Now let's go ahead and install our hitch. To begin with you'll need to locate the four bolts that'll need to be removed from the factory.
Trailer Hitch Installation - 2012 Toyota Prius - Hidden Hitch
All right, today on this 2012 Toyota Prius, were going to install part number 60263 from Hidden Hitch. All right, this is what the hitch looks like when its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 12 inches. From the center of the hitch pinhole to the edge of the bumper will be about 2 inches. Now Ill go ahead and show you how the hitch is installed. All right, the first thing we need to do is go ahead and move the tie down hook on the driver side.
Trailer Hitch Installation - 2010 Toyota Prius - Hidden Hitch
Today on this 2010 Toyota Prius well be installing the Hidden Hitch, part number 60263. This is what our hitch will look like once its installed. Now well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is two inches. From the top of the receiver tube to the ground is 10 inches. This will assist you with selecting accessories such as a bike rack or a cargo carrier.
Trailer Hitch Installation - 2006 Toyota Prius
Today on this 2006 Toyota Prius, were going to install part number 60894 from Hidden Hitch. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories, such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pinhole to the outside edge of the bumper, 2-1/4 and from the top of the receiver opening down to the ground, 11-1/4. Now, Ill go ahead and show you how the hitch is installed. Our first step is to go ahead and remove the plastic panel thats underneath the vehicle on the driver side.
