Today on this 2010 Toyota Tundra pickup truck, we are going to install part number 41935 from Draw-Tite. Alright, the hitch is going to mount up in the same exact place where the angle iron bracket is. So that is going to have to be removed and the hitch is going up in the same place as the existing fasteners that are already there. Further forward on the vehicle frame, these two holes that are already threaded in the frame, the hitch will use those to mount up to also. It is identical on both side. Right now we are looking at the passenger side of the vehicle. Alright, with the two bolt holes on the side of the frame it is a good idea to go ahead and spray them down a couple of times with WD-40, just to clean out some of the grit in there. Even though this is a brand new vehicle, there is sand there on the other side. So, do not ask me how it got there but there was. We will just clean them out and run a bolt in to make sure everything starts OK. On older vehicles, you will probably have to clean these out a little bit more for anything that has possibly happened in later years. We just want to make sure that the threads are good before we let the bolts in with the hitch. 1:17
We are going to go ahead and install the hitch onto the frame of the vehicle. It is going to be a good idea to have an extra set of hands because this is quite the awkward beast. We have one bolt on each side holding everything together. Lets go ahead and put our hardware on. We have a flat washer, a lock washer and a nut. Now again, the bolt was the original bolt that was going in there, in the truck, so we needed to keep those. Lets just go ahead and do the other three remaining bolt holes and just get the hardware installed loosely. Now we are going to go ahead and reinstall these factory bolts but with the addition of a conical tooth washer. And we will go ahead and reinstall it. Alright, on the frame mounts what is going to happen is that the block is going to sit between the frame and the hitch. So we have to pop the hitch out just a little bit to sneak it inside there. We use a little pry bar. We will use a screw driver to kind of get us the rest of the way there. Alright, then another block goes on the outside. We need block, lock washer and bolt. And go through and we will get those started. We will do the same thing for the last bolt going forward. 2:43
Once you get all of the bolts started, you can just go ahead and snug them down. Make sure they are all drawn down properly. Once we have all of our bolts drawn down, we can go ahead and torque the bolts as specified in the instructions. Alright, with that that finishes our install of part number 41935 from Draw-Tite. 3:46
Trailer Hitch Installation - 2013 Toyota Tundra - Hidden Hitch
Today on our 2013 Toyota Tundra we'll be installing Hidden Hitch, part number 87434.This is what our hitch will look like once its installed. Next we'll go ahead and give you a couple ofmeasurements to assist you with selecting accessories for your new hitch. From the centre of thehitch pin hole to the outermost edge of the bumper is 1. From the top of the inside of the receivertube opening to the ground is 18. This will assist you in selecting accessories, such as a ball mount,bike rack or cargo carrier. Now lets go ahead with installation.First we'll need to remove the angle brackets that are located on the inside of the framerail, near thebumper on both sides.
Trailer Hitch Installation - 2013 Toyota Tundra - Draw-Tite
Today on our 2013 Toyota Tundra, we'll be installing the Draw-Tite Hitch, part number 75527. This iswhat our hitch will look like once its installed.Next we'll go ahead and give you a couple of measurements to assist you with selecting accessoriesfor your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 1.From the top of the inside of the receiver tube opening to the ground is 18. This will assist you inselecting accessories such as a ball mount, bike rack, or cargo carrier. Now lets go ahead withinstallation.First we'll need to remove the angle brackets that are located on the inside of the frame rail near thebumper, on both sides. To remove the brackets, there are a total of four fasteners for each.
Trailer Hitch Installation - 2013 Toyota Tundra - Draw-Tite
Today on our 2013 Toyota Tundra well be installing the Drawtite Ultra frame hitch part #: 41935. This is what our hitch will look like once its installed. Next, well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is two inches. From the top of the receiver tube opening to the ground is 18 and a quarter inches. This will assist you with selecting accessories such as a ball mount, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2013 Toyota Tundra - Curt
Today on our 2013 Toyota Tundra we'll be installing the Curt Trailer Hitch, part number 13198. This is what our hitch will look like once it's installed. Next, we'll give you a couple measurements to assist you selecting accessories for your new hitch. The center of the hitch pin hole is even with the outer edge of the bumper, and top of the receiver tube opening to the ground is 18". This will assist you selecting accessories such as a ball mount, a bike rack, or cargo carrier. Now let's go ahead with installation.
Trailer Hitch Installation - 2001 Toyota Tundra - Hidden Hitch
Today on our 2001 Toyota Tundra we'll be installing the Hidden Hitch part number 87588. This is what our hitch will look like once installed. Next we'll go and give you a couple of measurements to assist you in selecting accessories to your new hitch. Such as the draw bar, a bike rack a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/4 inches. From the top of the receiver tube to the ground is 19 inches.
Trailer Hitch Installation - 2002 Toyota Tundra - Draw-Tite
Alright, today on this 2002 Toyota Tundra, well going to install part number 75105 from Draw-Tite. This is what the hitch looks like once its installed on the truck. Next well go ahead and give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin opening to the edge of the bumper is going to be 4 inches and from the top of the receiver opening down to the ground will be 20 inches. Now well go ahead and show you how the hitch is installed.First thing we need to do is go ahead and locate the threaded holes that are in the frame. Well spray them down with lubricants first.
