Select Your Vehicle
view cartView Cart

CALL NOW - 800-298-8924

Product Experts Available Now!

Free Shipping on Orders Over $99

Only 6 Hours 36 Minutes Remaining



Trailer Hitch Installation - 2009 Saturn Outlook

content loading



Saturn Outlook Trailer Hitch



Installation of a Trailer Hitch on a 2009 Saturn Outlook


Today on this 2009 Saturn Outlook we are going to install part number 75528 from Draw-Tite. This also applies to part number 87435 from Hidden Hitch. The first thing we need to do is remove this small panel at the bottom of the bumper here. There are two little tabs that you just twist, it removes, that is it. The actual panel itself will stay off because the hitch will be in the way from here on out. :26

Now we need to lower the exhaust to give us some working room on the passenger side of the vehicle. There is one on each side of the muffler. We will spray down the rubber hanger here with some lubricant. Now that we have it lubricated, we are going to push pull the exhaust hangers off the exhaust. With the exhaust cleared out of the way we can show you were the attaching points will be on the vehicle. :55

First off, looking at the driver side of the vehicle we have these two threaded holes right here that we are going to use. They will be the same on both sides of the frame. On the bumper structure itself there are two more threaded holes here and here that the hitch will use also. Next thing we want to do is clean out the threads on the frame, we are going to use a lubricant to loosen all the junk in there. We will go ahead and run our hitch bolt in to make sure we get everything cleared out. Now the older the vehicle the worse it is going to be. It may take some time to run the bolts in and out. 1:28

At this point we can lift the hitch up in position and install the bolts. It is a good idea to have an extra set of hands to hold up the other side until you get the bolts installed. Now take the two bolts that are going through the bumper structure, leaving our hitch as loose as possible, we will go ahead and thread these bolts in. Once we get everything started we can snug down the bolts and then torque them down as specified in the instructions. With our hitch torqued down we can go ahead and reinstall the exhaust hangers. Now that we have the vehicle off the life we are going to give you a couple measurements to help you hitch accessories for your vehicle. First off, from the top of the receiver tube to the ground is 19-3/8 inches. From the center of the hitch pin hole to the outside edge of the bumper is looking about 5 inches. That will finish our install of Draw-Tite part number 75528 on a 2009 Saturn Outlook.



Info for these parts were:


Test Fit:
Joe V

Video Edited:
Zack K

Video Edited:
Andrew K

Test Fit:
Patrick B

Video Edited:
Joshua S

Test Fit:
Nicholas E

Video Edited:
Jacob T

Test Fit:
Rick A

Test Fit:
Shane T

Video by:
Alan C

Video Edited:
Chris R

Video Edited:
Sue W

At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.

Ask your question or add a comment to this video?

Name: (example: John S.)



Contact email:



Comment or Question



Yes, I would like an email notification if someone replies to my comment?   






Saturn Outlook Trailer Hitch Videos



Trailer Hitch Installation - 2008 Saturn Outlook

Today on this 2008 Saturn Outlook we're going to install of part number 75528 from Draw-Tite. This will also apply to part number 87435 for Hidden Hitch. This is what the hitch looks like once installed on the vehicle. Next, we'll give some measurements that help you out in selecting the some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin to the edge of the bumper were looking at 3 1/4" and from the top of the receiver opening down to ground were looking at 18-1/4". Now, we're going to show you how the hitches install. All right, we'll go ahead and show you how the hitch mounts up onto the frame.



Trailer Hitch Installation - 2007 Saturn Outlook

Today on this 2007 Saturn Outlook we are going to install part number 75528 from Draw-Tite. This will also apply to part number 87435 from Hidden Hitch. As showing here the hitch is already installed on the vehicle. From the top of the receiver tube down to the ground is going to be 18-3/ 4 inches. From the center of the hitch pin out to the outside edge of the bumper is going to be about 4-1/ 2 inches. Next we are going to show you how it got there. The first thing we need to do is remove the rear fascia door that is basically at the bottom of the vehicle bumper cover. The next thing after that we will lower the exhaust. There are two rubber hangers on each side of the exhaust pipes. 00:38



see all 25 Saturn Outlook videos       








Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email





Free Shipping on Orders Over $99

Only 6 Hours 36 Minutes Remaining


etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com