Trailer Hitch Installation - 2009 Buick Enclave

This Product Fits The Following Vehicles

2007 - 2009 GMC Acadia All Models

2007 - 2009 Buick Enclave All Models

2007 - 2009 Saturn Outlook All Models

2009 - 2009 Chevrolet Traverse All Models

Products Featured in this Video

Installation of a Trailer Hitch on a 2009 Buick Enclave

Today on this 2009 Buick Enclave, we will be installing Draw-Tite hitch part number 75528. This hitch installation will also apply to Hidden Hitch part number 87435. Okay before we get started with our hitch installation we need to do a couple things in preparation. First we have already lowered the spare tire to get it out of the way. On the Enclave here we have got this rear fascia door that our hitch opening is actually going to come out through so we want to go ahead and remove this by simply turning the thumb screws here at the bottom of the door and pulling it away. We are going to go ahead and also need to lower our dual exhaust down. There are four hangers that we are going to need to lower the exhaust off of in order for us to have enough room to get the hitch into place. We have got two in here on the inboard side.

One here. And one here. And there is also an outboard one on each one of the exhaust tubes. Spray the studs down with a spray lubricant like a WD-40. That will make the removal of the hanger much easier. And then we can just take a pry bar and and slide it in and slide the hanger right off. Before we remove the final hanger we want to make sure we go ahead and support our exhaust tube here in the middle. I am just going to use the basic ratchet strap to support the exhaust tube because once we remove it off all four hangers it could fall down and possibly damage your exhaust. Here at the bottom of the frame you can see we have got two existing weld nuts and we are going to be using the new hardware provided with our installation kit to attach the hitch to those weld nuts there. And it is going to be the same on the passenger side as well.

We will be attaching the hitch to the frame using the 12 millimeter bolts and the conical tooth washers. And then here at the bottom of the bumper we have got two attaching points where we just removed that fascia door. To attach the hitch to those holes we are going to be using the handle nut as well as the 1/ 2 inch bolt and the conical tooth washer. Before we put the hitch up we will go ahead and manipulate the handle nut so they are ready to go. Get those handle nuts in place and we can go ahead and put the hitch up in position. We want to make sure we go up and over the exhaust on both sides. You want to make sure before we put our hex bolts and do our handle nuts that we place the small spacer in between the hitch and the frame. Now we are just going to go back through and tighten the bolts down. You will find the torque ratings on the directions included with the installation kit. Now that we have got the bolts torqued down, we can actually go ahead and flatten these handle nuts out. Then we just want to go ahead and put our exhaust back up on its hangers and then replace our spare tire and then our installation will be complete. And that will conclude the installation of hitch part number 75528 on a 2009 Buick Enclave.

Buick Hitch Installations

Trailer Hitch Installation - 2004 Buick Rendezvous
Trailer Hitch Installation - 2005 Buick Tarazza
Trailer Hitch Installation - 2002 Buick LeSabre
Trailer Hitch Installation - 1995 Buick Le Sabre

Buick Wiring Installations

Wiring Harness Installation - 2005 Buick Tarazza
Wiring Harness Installation - 2009 Buick Enclave

Trailer Hitch Help

Specialty Trailer Hitch Review
Trailer Hitch Receiver Sizes
Trailer Hitch Types Review
Trailer Hitch Installation Tips
What Do I Need To Tow A Trailer?
Trailer Hitch Classes Review

Trailer Hitch Help - Videos

Cleaning Weld Nuts for Trailer Hitch Installation
Handle Nut Demonstration
Drilling to Enlarge a Frame Hole for Hitch Install
Drilling a Spare Tire Pan for a Trailer Hitch Installation
Using Fish Wire for Trailer Hitch Installation
Lowering Exhaust Example for Trailer Hitch Installation
Lowering Exhaust Pipe on Vehicle with Rubber Hanger
Using Stove Wire as a Bolt Leader Demonstration
Class III Trailer Hitch and Weight Capacities Review
Class II Trailer Hitch and Weight Capacities Review
Class I Trailer Hitch and Weight Capacities Review
Trailer Hitch Classes and Weight Capacity Comparison

Ask the Experts

Do you have a question about a product or how something works? With thousands of product installations and troubleshoots under our belts, we don't just sell this stuff, we know how to install and use it. Just type your question in the box below.

It may be helpful to include the year, make, and model of your vehicle if you have a question about a custom fit product.

Name:

Contact email:

Subject:

How can our experts help?