customer service | view cart 
Trailer Hitch Installation - 2007 Jeep Grand Cherokee
Custom Fit Trailer Hitch
This Product Fits The Following Vehicles
2006 - 2009 Jeep Commander
2005 - 2005 Jeep Grand Cherokee All Models
2006 - 2009 Jeep Grand Cherokee All Models, except SRT8
Products Featured in this Video
Manufacturer Instructions
Installation of a Trailer Hitch on a 2007 Jeep Grand Cherokee
Today on this 2007 Jeep Grand Cherokee we are going to be installing Hidden Hitch part number 87752. This installation will also apply to the Draw-Tite part number 75338. Okay we are underneath the vehicle. We are looking at the rear bumper structure, we have four holes that we will be using as our attaching point for the trailer hitch. The hitch is actually going to go up around both sides of the bumper structure and we are going to put the bolts through each one of the holes and attach it to the weld nuts built into the hitch.
Before we get started we need to remove two of the plastic push rivets that are holding the bumper to the bumper structure. Okay with those two removed we can kind of push the bumper fascia away from the bumper structure here enough where we can get the hitch up and around. And we will be attaching the hitch to the bumper structure using the 4 inch long 1/ 2 inch hex bolts along with the conical tooth washers.
If you are finding that there is an excessive gap in between the trailer hitch and the bumper structure itself, you can go ahead and use these flat washers that are provided in the installation kit and slide them in between the hitch assembly itself and the bumper structure around each one of the bolts and that will help ship up the extra space that is in there. Now you can see by tightening those down it pulled the hitch up nice and tight to the frame, so we do not have to worry about putting any extra flat washers in there. I am going to go back through and torque the bolts down now. You want to check with the directions to verify the appropriate torque rating for each individual bolt. Okay with the bolts torqued down we can go ahead and put our push rivets back into place. And this will conclude the installation of part number 87752 on a 2007 Jeep Grand Cherokee.
Questions About Part 75338
Will I need to cut bumper to install hitch 75338 on 2006 Jeep Grand Cherokee Ltd.?
Filter Videos
- Search By Other Makes
- Acura (4)
- Audi (1)
- BMW (2)
- Buick (5)
- Cadillac (1)
- Chevrolet (36)
- Chrysler (16)
- Dodge (29)
- Ford (44)
- GEO (1)
- GMC (8)
- Honda (24)
- Hyundai (11)
- Infiniti (1)
- Isuzu (1)
- Jeep (18)
- Kia (9)
- Lincoln (2)
- Mazda (11)
- Mercury (2)
- Mitsubishi (4)
- Nissan (12)
- Oldsmobile (2)
- Pontiac (9)
- Saab (1)
- Saturn (4)
- Scion (2)
- Subaru (6)
- Suzuki (1)
- Toyota (27)
- Volkswagen (5)
- Volvo (1)
- Trailer Hitch Help
Specialty Trailer Hitch Review- Trailer Hitch Receiver Sizes
- Trailer Hitch Types Review
- Trailer Hitch Installation Tips
- What Do I Need To Tow A Trailer?
- Trailer Hitch Classes Review
Trailer Hitch Classes and Weight Capacity Comparison- Class I Trailer Hitch and Weight Capacities Review
- Class II Trailer Hitch and Weight Capacities Review
- Class III Trailer Hitch and Weight Capacities Review
- Using Stove Wire as a Bolt Leader Demonstration
- Lowering Exhaust Pipe on Vehicle with Rubber Hanger
- Lowering Exhaust Example for Trailer Hitch Installation
- Using Fish Wire for Trailer Hitch Installation
- Drilling a Spare Tire Pan for a Trailer Hitch Installation
- Drilling to Enlarge a Frame Hole for Hitch Install
- Handle Nut Demonstration
- Cleaning Weld Nuts for Trailer Hitch Installation
Search
Contact and Help
What our customers said:
Nice shopping experience. Good selection and prompt shipment. After I see the products in person, I am sure that I will be back for more. Best, Jim
Jim
Powell, OH
