Today on this 2002 Hyundai Santa Fe we are going to be installing part number 87419 from Hidden Hitch. As you can see we already removed our spare tire. Then we are going to lower the exhaust. First thing we are going to do is remove our exhaust hangers after we lower our spare tire. We are just going to lubricate up the hangers. There is going to be two on both sides of the muffler at the rear most of the vehicle. We are just going to lube them up with WD-40 and then we are going to slide them off. 00:29
We are going to show you the mounting locations now. On the driver side of the vehicle there is going to be five locations and they are going to be here. On the passenger side of the vehicle there is only going to be three locations and they are going to be here, here, and here. Now we are going to clean out our threads. We are just going to spray them down with a lubricant and run our wire brush in there and out and just clean out any loose debris in our threads. 00:58
Now that we have all of our holes cleaned out we are going to put our hitch in position. You might want to get a second set of hands to help hold the hitch up while you thread in your bolts. We are going to be installing our hitch with the conical tooth washer and bolt that are supplied in the kit. As you can tell there is going to be one bolt that is going to be larger than the other ones. That one is going to go farthest forward. 01:20
Now that we have got our bolts in position we are going to tighten down and torque as specified in the instructions. Now that we have our hitch installed and our bolts torqued down we are going to put our exhaust back into place by just putting them back on the hangers that we took off previously. Now we will take a couple of measurements for you. From the center of the hitch pin hole to the edge of the bumper is going to be approximately three inches. From the top of the receiver tube opening to the ground is going to be approximately 15 inches. This will complete the install for part number 87419 on this 2002 Hyundai Santa Fe.
Trailer Hitch Installation - 2013 Hyundai Santa Fe - Curt
Today on our 2013 Hyundai Santa Fe well be installing the Curt hitch, part number C13134. Before we begin our install heres what the hitch looks like when its installed on the vehicle. Well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is five and a half inches. From the top of the inside of the receiver tube opening to the ground is 12 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2012 Hyundai Santa Fe - Curt
Today on our 2012 Hyundai Santa Fe well be installing the Curt hitch, part number C13073. This is what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is four and a half inches. From the top of the receiver tube to the ground is 15 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2011 Hyundai Santa Fe - Draw-Tite
Today on our 2011 Hyundai Santa Fe, we're going to install the Draw-Tite Hitch, part number 36511. This is what our hitch will look once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3-1/4 inches. From the top of the receiver tube to the ground is 13 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier.
Trailer Hitch Installation - 2010 Hyundai Santa Fe - Draw-Tite
Today on this 2010 Hyundai Santa Fe, were going to install part number 75684 from Draw-Tite. This is what the hitch looks like once installed on the vehicle. Next well go ahead and give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pinhole to outside edge of the bumper is going to be 3 inches and from the top of the receiver opening down to the ground is going to be 13 inches. Now well go ahead and show you how the hitch is installed.First off, well show you where the hitch attaches to the vehicle. There are two weld nuts that are located at the bottom of the frame close to the bumper.
Trailer Hitch Installation - 2008 Hyundai Santa Fe
Today on this 2008 Hyundai Santa Fe, we're going to install part number 87414 from Hidden Hitch. This is what the hitch looks like when it is installed on the vehicle. Next, we'll give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground is going to be 13 inches and from the center of the hitch pinhole to the outside edge of the bumper will be 5-3/4 inches. First thing we'll do is we'll show you where the hitch mounts up to the frame as these two existing threaded holes here. Next step is to go ahead and clean up the threaded holes.
