Today, we're going to look at Dexter's 12" Nev-R-Adjust Electric Brake Assembly for Left-Hand Side, part number 23-464. This is a 12" x 2" electric assembly. Measure the diameter across the shoes, and there is a 12" figure. Then we'll measure the width of the shoes, and there is a 2" figure. When paired up with the assembly for the right-hand side, these brakes are weighted for axles at 7,000 pounds. The assembly mounts on a 5-bolt pattern.
So check your trailer axle to make sure it uses the same 5-bolt pattern. There is a pair of electric wire leads that run to our magnet that you're use for electrical connection. It doesn't matter, which wire you use for ground and which wire you use for your brake feed, so long as you have a good electric connection. This is a self-adjusting brake assembly. Meaning overtime, you don't have to go back and adjust the brakes for proper tension.
When you first install the brakes, you will need to set them by rotating the star wheel that will open up to shoes. You want an even light amount of tension on the drum as you rotate it around. Overtime as you back the trailer with brakes applied tension will be put on this cable that will in-turn power actuator that will advance the star wheel when tension needs to be added. Since this is electric brake assembly, you don't want to use it on boat or marine trailer applications. We know this assembly is for the left-hand side, because the short shoe will go towards the front of the trailer and the longer shoe will face to back of the trailer.
Electric brake assemblies work as the hub and drum rotates around the assembly and you apply brake pressure, the magnet will activate and it will stick inside the drum. As the drum drags along the magnet, it's going to pull on this arm, which in-turn will open our brake assembly and apply pressure. And that does it for the Dexter 12" Nev-R-Adjust Electric Brake Assembly for Left-Hand Side, part number 23-464.
This Old Trailer: Changing Hydraulic Trailer Brake to Electric
Today on This Old Trailer we are going to replace hydraulic brakes with electric brakes. Basically it is going to be a matter of taking off the tires, removing the hubs, go ahead and removing the backing plates and drain the hydraulic lines of fluid, and then going ahead and bolting on the new brakes. We will start off, obviously, by taking the wheels off. OK, go ahead and remove the dust cover here. It is an E-Z Lube spindle so this has a tang washer that we need to bush back down so we can unlock the castle nut right here. Just push it back down. Now we should be able to take the hub right off. The next task is to go ahead and disconnect the hydraulic lines. We have that disconnected. Now we need to pull the clip out so we can release this part here. And that is just a little piece of metal right here that you can just pry out. Alright, now we can unbolt this at the back of the hydraulic backing plate. Alright, now we can unbolt the backing plate from the flange on the axle. Now we are down to our bare axle. We will clean it up a little bit and then reinstall the brakes. 1:24
This Old Trailer: Electric Trailer Brake Installation Part 1
Alright, today on This Old Trailer, what we are going to do is install electric brakes. Right now this trailer does not have any brakes on it whatsoever, so it has two drag axles. So the first thing that we need to do is go ahead and take off the rear wheels. And then we will go ahead and take off the hubs. At this point we will take off the dust cap on our axle. And basically what you want to do is on this particular unit we have an E-Z Lube cap, so it fits kind of tight. It is a good idea to go ahead and rotate the hub and lightly strike it and then I will just back it off with a screw driver behind the flange. And then pry it off. Alright, let us wipe off the excess grease on the end of the spindle here and we will get to our tang washer. And we will release it so we can back off the castle nut. Alright, we have it cleaned up a little bit. Now right here, this is the tab I was talking about. That is our tang washer. Take this. Push it down flat to the flat spot on our spindle and then you can take the castle nut off. 1:07
All right today we are going to show you a typical brake inspection. Basically what we are going to do is take off the brake hub here and we are going to inspect the brakes, the linings, the springs, and the display cylinder inside. First off we will go ahead and take off the dust cap. In this case it is a bearing buddy. Next, is taking out the locking pin. There is either a cotter pin that goes in the center here but once you get that lock washer off you have to go ahead and just take off the nut and pull your whole hub off. First thing you want to check for is grease on the linings, and sure enough we have got grease all over these linings here. Also on this side here and probably smeared around over to the other side as you can tell.
All right today we are going to show you how to bleed hydraulic brakes on a trailer. First off you want to top off your master cylinder, with appropriate fluid. To pump the fluid from the master cylinder out, there is a couple of different ways of doing it. Sometimes it will have the emergency lever the and the safety chain will pull. Okay what you can do is unbolt the plate that holds the lever in place and then use that lever to actuate the master cylinder and force the fluid through. Some of them, you are going to have to go where the ball goes and manually activate it. Pull it in and out. Or like on this model here there might be a little lever underneath here that you could use.
Trailer Hub Brake Magnet Replacement Demonstration
When one wheel does not seem to be stopping as quick as the others it may be because the brake magnet needs to be replaced. We put together a short video to help you recognize this problem and to show you how easy it is to fix it. Keep your trailer safe for yourself and others on the road by checking and replacing parts like the brake magnet when needed.
Trailer Brakes and Wiring Installation
Today we are going to show you how to install brakes on a trailer that does not have existing brakes. It is actually pretty easy to do. It is just very time consuming. There are a couple of things you want to look out for before you start. You want to step behind your trailer, and look behind the existing hub you have. Make sure you have a flange like this on the axle. It is this 4-bolt flange on here; if you have that on your axle you are pretty much home free. This size flange has four bolts. You will see it on 3,500- pound axles like we have here. You also see it on 2,000- pound axles. On a 3,500 -pound one you would probably use a 10- inch drum and on a lighter axle, 2,000 pounds, you probably would use a 7- inch size. Also you notice we have the hub missing. We have to take that off because the hub and drum assembly is all in one piece. It is not like the automotive application. You have to take off the old hub, discard it, and start off fresh.
