Today we are going to review part number 23-27. This is the Dexter ten-inch electric brake assembly for the right hand side. This electric brake assembly will measure ten inches by 2-1/4 and the way that is measured is the diameter of the shoes across. Its ten inches and the width of the shoe will be 2-1/4. This is passenger side brake assembly, which is the right hand side, and the way you can tell that is the shorter shoe will face the front of the trailer and the longer shoe will face the rear of the trailer. When this assembly is paired with a left hand side assembly, itll be rated for an axle 235 pounds.
You can use a wheel size of 13, 14 or 15 and this brake certainly does have a four bolt-mounting flange as you can see here. It does include the four studs. What you want to do is to make sure it fits your four bolt-mounting flange is if you can measure the distance between the holes. In the case they measure 2-7/8 inches. That is the distance from the center to center of the mounting flange.
This is an electric brake assembly so its not really used for marine applications. There are two wire connections to be made. One is for the brake feed, the other is for the ground and it doesnt matter which wires you use for either connection. Down here is the star wheel, which is used for adjusting the brakes and what you will, is an access hole back here that you pull the plug out. Use a brake-adjusting tool in each end and you will adjust the star wheel for the brakes to go either in or out.
And, this is an electric brake assembly and the way that would work is when power is fed to this magnet, its magnetized and will come out and sticks to the surface, inner surface of the hub and drum assembly, which will in turn pull the brake arm. This arm right here. It will attach and pull it, which will apply the brakes outward to stop the hub and drum. This part does have a limited one-year warranty and that should do it for part number 23-27.
Today on This Old Trailer we are going to replace hydraulic brakes with electric brakes. Basically it is going to be a matter of taking off the tires, removing the hubs, go ahead and removing the backing plates and drain the hydraulic lines of fluid, and then going ahead and bolting on the new brakes. We will start off, obviously, by taking the wheels off. OK, go ahead and remove the dust cover here. It is an E-Z Lube spindle so this has a tang washer that we need to bush back down so we can unlock the castle nut right here. Just push it back down. Now we should be able to take the hub right off. The next task is to go ahead and disconnect the hydraulic lines. We have that disconnected. Now we need to pull the clip out so we can release this part here. And that is just a little piece of metal right here that you can just pry out. Alright, now we can unbolt this at the back of the hydraulic backing plate. Alright, now we can unbolt the backing plate from the flange on the axle. Now we are down to our bare axle. We will clean it up a little bit and then reinstall the brakes. 1:24
Alright, today on This Old Trailer, what we are going to do is install electric brakes. Right now this trailer does not have any brakes on it whatsoever, so it has two drag axles. So the first thing that we need to do is go ahead and take off the rear wheels. And then we will go ahead and take off the hubs. At this point we will take off the dust cap on our axle. And basically what you want to do is on this particular unit we have an E-Z Lube cap, so it fits kind of tight. It is a good idea to go ahead and rotate the hub and lightly strike it and then I will just back it off with a screw driver behind the flange. And then pry it off. Alright, let us wipe off the excess grease on the end of the spindle here and we will get to our tang washer. And we will release it so we can back off the castle nut. Alright, we have it cleaned up a little bit. Now right here, this is the tab I was talking about. That is our tang washer. Take this. Push it down flat to the flat spot on our spindle and then you can take the castle nut off. 1:07
All right today we are going to show you a typical brake inspection. Basically what we are going to do is take off the brake hub here and we are going to inspect the brakes, the linings, the springs, and the display cylinder inside. First off we will go ahead and take off the dust cap. In this case it is a bearing buddy. Next, is taking out the locking pin. There is either a cotter pin that goes in the center here but once you get that lock washer off you have to go ahead and just take off the nut and pull your whole hub off. First thing you want to check for is grease on the linings, and sure enough we have got grease all over these linings here. Also on this side here and probably smeared around over to the other side as you can tell.
All right today we are going to show you how to bleed hydraulic brakes on a trailer. First off you want to top off your master cylinder, with appropriate fluid. To pump the fluid from the master cylinder out, there is a couple of different ways of doing it. Sometimes it will have the emergency lever the and the safety chain will pull. Okay what you can do is unbolt the plate that holds the lever in place and then use that lever to actuate the master cylinder and force the fluid through. Some of them, you are going to have to go where the ball goes and manually activate it. Pull it in and out. Or like on this model here there might be a little lever underneath here that you could use.
When one wheel does not seem to be stopping as quick as the others it may be because the brake magnet needs to be replaced. We put together a short video to help you recognize this problem and to show you how easy it is to fix it. Keep your trailer safe for yourself and others on the road by checking and replacing parts like the brake magnet when needed.
Today we are going to show you how to install brakes on a trailer that does not have existing brakes. It is actually pretty easy to do. It is just very time consuming. There are a couple of things you want to look out for before you start. You want to step behind your trailer, and look behind the existing hub you have. Make sure you have a flange like this on the axle. It is this 4-bolt flange on here; if you have that on your axle you are pretty much home free. This size flange has four bolts. You will see it on 3,500- pound axles like we have here. You also see it on 2,000- pound axles. On a 3,500 -pound one you would probably use a 10- inch drum and on a lighter axle, 2,000 pounds, you probably would use a 7- inch size. Also you notice we have the hub missing. We have to take that off because the hub and drum assembly is all in one piece. It is not like the automotive application. You have to take off the old hub, discard it, and start off fresh.