Question:
Please advise how to connect a prodigy p2 brake controller to a 2010 Mazda BT50 Boss ute. Factory fitted towbar has been fitted. Specifically I would like a wireing diagram please.
asked by: Dave
Expert Reply:
In order to install a 4 and 7-Way installation kit # ETBC7, you will need to have a 4-Way trailer connector or install one using # 119175KIT. I have included some links that will help with this installation.
Installing the P2, # 90885, with the ETBC7 kit is fairly straight forward. I have included a link to an FAQ article and a link to a video that explains the installation for you. One of the FAQ links has a simplified diagram at the bottom of the page. The video shows the P3 being installed but it will be the same wiring as the P2.
expert reply by: Michael H
Products Referenced in This Question
Upgraded Circuit Protected Taillight Converter Hardwire Kit with 4 Pole End (Includes Testers)
Product Summary:
Trailer Hitch Wiring
Converter
3 Wire System
Universal Fit
Product Specs:
4 Flat
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
Product Summary:
Proportional Controller
Electric
Electric over Hydraulic
Digital Display
Vehicle Mount
Product Specs:
Automatic Leveling
2 - 8 Brakes
360 Degrees
Product Page this Question was Asked From
Universal Installation Kit forTrailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
Product Summary:
Brake Controller
Accessories
2 - 8 Brakes
10 Gauge Wire
Product Specs:
Connector
Brake Controller Wiring
Wired to Brake Controller
Parts Needed to Install a Trailer Brake Controller on a 2003 Ford Ranger with Factory 4-WayParts Needed to Install a Trailer Brake Controller on a 2004 Land Rover Discovery IIIsolator Recommendation to Prevent a Trailer Battery from Draining a Vehicle BatteryParts Needed to Convert a Factory 4-Way from a 2006 Nissan Pathfinder to a 7-WayPower Wire Routing Recommendations for a 2007 Subaru Forester for an # ETBC7 KitIs 40 amp Breaker Included with ETBC7 Sufficient for Use with 10 Gauge WireParts Needed to Install a Tekonsha P2 Trailer Brake Controller on a 1997 Ford Explorer with 4-Way2008 Ford Edge Brake Controller Install Instructions and RecommendationBrake Controller 7 and 4 Way Installation Kit without the Pre-wired 7 and 4 way Trailer ConnectorYellow Side Marker Lights Will Not Light Up on Trailer Towed by a 2006 Dodge Ram 1500Recommendation for Brake Controller and Wiring on 2008 Chrysler PacificParts Needed to Install a Hayes Electric Trailer Brake Controller on a 2005 Nissan PathfinderInstalling 7-Way Trailer Connector on 2006 Nissan FrontierIs the 10 Gauge Wire from the Brake Controller Kit # ETBC7 Sufficient to Power a RefrigeratorHopkins Impulse Brake Controller Showing a Reading no Trailer Connected on 2004 Chevy SilveradoElectric Trailer Brake Controller Recommendation for a 2010 Dodge JourneyNo Trailer Connection on Tekonsha P3 Brake Controller 90195 on a 2000 Toyota TundraHow to Determine Towing Capacity 2003 GMC Envoy 4-Wheel Drive with 6 Cylinder 4.3L EngineWhat is Error Code E1 on Hopkins Proportional Brake Controller # HM47294 on my 2006 Chevy 2500HDWhat is Needed to Set Up a 2006 Nissan Pathfinder to Tow a Trailer with Electric BrakesIs Installation Kit, # ETBC7, Required on 2008 Dodge Ram if a Trailer Does Not Have Electric BrakesBrake Controller and 7-way Connector Wiring for 2007 Dodge Dakota Quad Cab PickupFeatured Help Information
Instructions for 119175KITInstructions for 90885
Brake Controller 7- and 4-Way Installation Kit (ETBC7)
Brake Controller Installation: Starting from Scratch
Trailer Brake Controller Installation - 2009 Toyota Tacoma - Video
Trailer Wiring Harness Installation - 2006 Kia Optima - Video
