How to Select Correct Ball Mount to Keep Trailer Level When Towed with Lowered 2013 Toyota Sienna
Question:
Im looking for a high low 2inch ball mount for My 2013 Toyota sienna. My problem is that this is the sports model, so its lowered. I current use a Reese 2in that I have flipped. I still am hitting the mount as I drive or of the driveway. The tent trailer is 1994 coleman, so weight is about 2k. Trailer as also is not level on the street. ..
asked by: Todd M
Expert Reply:
The desired situation when towing is that your choice of ball mount will allow your trailer's frame to remain level with the ground when hitched, since level trailers handle better. Towing with either a lowered or lifted vehicle can make it a challenge to keep the trailer level.
Vans like the Toyota Sienna and Honda Odyssey are pretty low to the ground in their stock form so any additional lowering will not help. For instance, when we installed Curt hitch # C13105 on a stock 2013 Sienna the top of the receiver opening was 11-inches above ground. The bottom of the hitch tube would then be only about 8-1/2-inches above ground.
The linked article will show you how to determine the exact amount of rise or drop you need from a ball mount. You can then use the linked page for 2-inch ball mounts to select one with the correct rise or drop, and weight capacity. Typically you will keep more ground clearance by using a fixed ball mount like # D-4 rather than an adjustable one like # C45900 which extends down lower.
You cannot use adapter MT70070 to give you increased height. The top receiver opening is only for use with accessories, but not for towing.
Products Referenced in This Question
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Channel Style Adjustable Ballmount - 2" & 2-5/16" Balls - 14,000 lbs
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- 2 Inch Ball
- 2-5/16 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 6 Inch
- Rise - 5 Inch
- Fits 2 Inch Hitch
- 14000 lbs GTW
- Class IV
- CURT
more information >
Product Page this Question was Asked From
Curt Ball Mount for 2" Hitches - 3/4" Rise, 2" Drop - 10-1/4" Long - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- No Ball
- 1 Inch Ball Hole Diameter
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Rise - 1 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- CURT
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: LED Replacement for Truck-Lite 60 on Triton Boat Trailer
- Article: How to Measure for Trailer Hitch Drop
- Article: Ball Mount Basics: Weight Capacity, Class, and Size
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: How to Get a Ball Mount with 0 inches of Rise or Drop
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Suggestions For Removing Play Between Draw-Tite QSP Silencer/Cover and End of Receiver
- Q&A: How to Determine If 2013 Chevy Equinox has Tow Package for Trailer Wiring
- Q&A: Installing DC Power And Power Inverter To Cargo Trailer
- Q&A: How To Install a 30 Amp Service on an Enclosed Cargo Trailer
- Q&A: Parts Needed and Wiring Methods for Adding 110 and 12 Volt Power and Accessories to a Trailer
- Article: Rooftop Cargo Carriers
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: Wiring a Tow Vehicle to Tow a Dinghy