Volkswagen Rabbit owners are most interested in these products
change vehicle
Volkswagen Rabbit Questions and Answers
- Hitch Recommendation for a 2007 Volkwagen Rabbit
- For your 2007 Volkswagen Rabbit you would want a Draw Tite Hitch part # 24825. This hitch has been confirmed to fit your vehicle.
The Draw Tite Hitch # 24679 that you referenced is a fit for other Volkswagen vehicles but not your Rabbit so I would not recommend it for you.
view full answer...
- Which Yakima Fairing for Roof Rack Installed on 2009 Volkswagen Rabbit
- When a Yakima roof rack is installed on a 2009 VW Rabbit, Yakima recommends the 44 inch fairing as being the best fit. When installed, the Q towers should be about 42-1/2 inches apart, so a 44 inch fairing would be perfect. Installing a fairing can greatly reduce noise caused by turbulence.
To see a product demonstration video, click the provided link.
view full answer...
- No Brake or Turn Signals With Curt PWM Wiring Harness # C56201KIT on 2008 Volkswagen Rabbit
- The issue that you are having sounds exactly like a poor ground connection, assuming the Curt PWM Wiring Harness, # C56201KIT, is wired correctly to your 2008 Volkswagen Rabbit. The stop and turn signals require more power than the running lights and a poor ground connection could prevent the power from reaching the 4-way connector.
The white wire should be grounded to a clean, bare metal surface on the vehicle frame or cross member. You should not have a problem using this kit on your vehicl
view full answer...
- Which Turn Signal Circuit is Used to Install a Tow Ready Harness # 119176
- When you install the Upgraded Circuit Protected Modulite with 4 Pole Harness and Hardwire Kit # 119176KIT you will want to use the rear tail lights. While it might be possible to use the front turn signals, the rear signals are the ones you will want to use.
To get a better idea how this product installs check out the install video I attached. Also check out the FAQ article I attached on installing trailer harnesses on 2008 and new Volkswagens.
view full answer...
- Will Replacement Quick Release Mounting Kit, # SR04952, Fit Around Yakima Round Crossbars
- On the Replacement Quick Release Mounting Kit, # SR04952, the distance between the holes on the mounting plate is 3-15/16 inches which is more than enough to fit around Yakima round roof rack crossbars. Yakima bars are 1-1/8 inches in diameter.
view full answer...
- Why is a Stabilizing Strap Recommended on Curt Hitches and what is Meant by Non-Trailer Load
- Non-trailer loads are hitch accessories like bike racks and cargo carriers. Basically anything that is not a trailer that you could put on a hitch. Curt recommends you use a Curt Trailer Hitch Support Strap # 18050 to help prevent excessive jarring on the hitch from bumps.
Basically you will attach one of the strap to the hitch accessory and the other end to the trunk lid of your vehicle and the support will help brace the setup to prevent excessive jarring of your hitch setup.
Check out t
view full answer...
- Direct Fit Cold Air Intake for a 2008 VW Rabbit with 2.5 liter Engine
- As long as your 2008 VW Rabbit has the 2.5 Liter Engine in it, the Takeda Attack Direct-Fit Cold Air Intake System with Pro Dry S Filter, # AFETA-6002B, will be a direct fit installation and will not require any modifications or cause the check engine light to come on, as long as it is properly installed.
We also recommend using the Restoration Kit, # AFETP-7015C, for aFe Pro Dry S Takeda Air Filters, to keep the filter clean and the filtration fibers in good condition.
view full answer...
- Will a Yakima Quickback 3 fit on a 2007 VW Rabbit
- I checked with Yakima and the Quickback 3 Bike rack # Y02621 that you referenced is a confirmed fit for your 2007 Volkswagen Rabbit 4-door hatch. Check out the review video and installation instructions I attached for you to check out also.
If you plan on carrying womens or alternative framed bikes you may be interested in purchasing a Yakima Tube Top Bike Adapter Bar # Y02531. I attached a review video and installation instructions for this product for you to check out also.
view full answer...
- Roof Rack Recommendation for a 2008 Volkswagen Rabbit 3-Door
- The Rola roof rack, # 59811, will only fit the 5 door model of the 2008 Volkswagen Rabbit. For a 2-door hatchback (3-door), I have linked the available roof racks. The Yakima rack is the most cost effective option. For it you would need the following parts:
Crossbars, # Y00409
Q102 Q Clips, # Y00702
Q Towers, # Y00124
I have included a link to a video that shows a typical installation of a Yakima roof rack for you.
view full answer...
- Which Trunk Mount Bike Racks Fit a 2008 Volkswagen Rabbit hatchback
- The Thule Passage 2 Bike Carrier, # TH910XT, is a fit for the 2008 Volkswagen Rabbit 3-door and 5-door models. I have included a link to the installation details and a link to a video review of the bike rack for you.
If you will be carrying womens, childrens, or alternative frame bikes, I recommend using the Bike Adapter Bar, # TH982XT, in order to carry the bikes more level. I have included a link to a video showing how the adpater works.
I have also included a link to all of the trunk mo
view full answer...
- Hitch Recommendation for a 2007 Volkswagen Rabbit
- A 2000 lb capacity trailer hitch would be like the Curt Trailer Hitch Receiver with Drawbar, part # 11074, that you referenced. You would not need to do any drilling or trimming for the installation of this product. Another benefit to this one is that it comes with a drawbar pin and clip. I attached installation instructions for this product for you to check out.
The 1000 lb trailer hitch is the Curt Trailer Hitch, part # 11099, and it requires some minor trimming of the fascia for installati
view full answer...
- Lights On Trailer Dim When Headlights Of My 2007 VW Rabbit Are Turned On
- If your 2007 VW Rabbit has a 3-wire system, your vehicle would have a combined stop and tail light circuit. To wire this system on your vehicle, you would need to attach the red stop light wire from part # 119190KIT, to the combined stop and tail circuit. Then attach the brown wire from the harness to the independent circuit. The wires for the turn signals will need to be wired in at the headlight assemblies at the front to the vehicle.
If your vehicle has the 2-wire system you will need to l
view full answer...
- Is Trimming Required for Installation of the 2008 Volkswagen Rabbit Hitch # 11074
- No, installation of the Curt Class I Trailer Hitch, item # 11074, on a 2008 Volkswagen Rabbit does not require trimming of the rear bumper fascia. I have included a link to the installation instructions for you to review.
To complete your Class I Towing setup you may also want to consider the following items.
Vehicle Wiring # 119176KIT
1-7/8 inch hitch ball # 19256
2 inch hitch ball # 19258
DeadBolt Hitch Lock # 7682
view full answer...
- Troubleshooting Turn and Brake Lights not Working with Running Lights on, 2009 Volkswagen Rabbit
- With a 3 wire system:
If your Rabbit has combined stop and tail lights AND has an additional tail light wire independent of the stop light wire, here is what you will need to do. Attach the red stop light wire from the harness to the combined stop and tail light circuit. Then attach the brown wire from the harness to the independent circuit. Turn signal functions will need to be tapped into at the front of the vehicle at the headlight assemblies.
If the vehicle has a 2 wire system:
The
view full answer...
- What Hitch Is Available to Fit A 2005 Or 2006 Volkswagen Rabbit
- The new body style VW Rabbit was introduced to the US as a 2006 model. I do not have a listing for a 2005 VW Rabbit, just a Golf. You might check to see if your VW Rabbit might be a 2006 model.
The Draw-Tite Class I Hitch, # 24679, will fit on a 2006 VW Rabbit but not the GTI V6 models. It attaches to the vehicles trunk floor. It has a gross towing weight capacity of 2,000 lbs. and a tongue weight capacity of 200 lbs.
With the # 24679 hitch if you will be towing you will need the Draw-Tit
view full answer...
- How Much of the Fascia Needs to be Trimmed and Does it Need to be Professional for Curt 11099
- Essentially you will cut a notch out of the fascia. It will probably be 1-3/4 inches wide due to the outside width of the receiver tube. I am not sure how far up the notch will have to be made. It may sit directly behind the bumper cover, so you would have to cut a 2 inch square hole in the center of the fascia. It does not have to be done by a professional, but not everyone is comfortable doing it. You will need a utility knife with a few blades to cut the notch.
The Hidden Hitch, part # 602
view full answer...
- Installation Instructions for Wiring a 2008 Volkswagen Rabbit to Tow a Trailer
- Due to the MX (Multi-Plexed) wiring system on your 2008 Rabbit, you will need the Tow Ready Wiring Kit, # 119190KIT, to add trailer wiring to your vehicle.
On the 2008 VW Rabbit, you will need to find the circuit that contains 12 volt brake and taillight functions and does not have the turn function on that wire. Attach the red stop wire from the # 119190KIT to this circuit.
Ground the white wire and the brown wire from the # 119190KIT to a good ground location that is free of paint, prime
view full answer...
all Volkswagen Rabbit questions
