Rain-X Latitude Wiper Blades Installation - 2012 Toyota Sienna
All right today on this 2012 Toyota Sienna, were going to do a test fit of part number rx5079282 from Rain-X, this is a latitude windshield wiper blade. To start off the test fit well go ahead and remove the original wiper blade, theres a small tab we have to pop open, well use a small screwdriver to do that, and then we can go ahead and slide the wiper blade off the arm. With the wiper blade off we can see that the arms a J-style, so our new Rain-X windshield wiper blade will go right into place. Well go ahead and line it up with the catch on the wiper blade and then slide it into place until it clicks. Well go ahead and lay down the windshield and you can see how it contours to the windshield. Okay were done with our driver side, lets go ahead and repeat the same process over on the passenger side, however; it uses a different size and a different part number and that part number is rx5079277.
Swagman Titan Hitch Bike Rack Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna, we'll be test fitting the Swagman Titan 4 Bike Carrier both 1-1/4 and 2 inches hitches, Part Number S63410. Now to begin our test fit, we'll slide the bike rank shank using the included two inch adapter into the hitch, line up the hitch pin hole, and install and tighten down our anti-rattle bolt. With the bolt tight, our bike rack is secured to the vehicle. We'll now go ahead and give you a few measurements. Our ground clearance here at the back of the bike rack measures 13 inches and from the closest point of the bike rack, here at the mast to the back of the vehicle measures 8-1/2 inches. We can now go ahead and pull the switch here on the base of the rack, which will allow us to tilt the mast down and open the cargo door.
Kuat Sherpa Hitch Bike Rack Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna, we'll be test fitting the Kua Sherpa Hitch Mounted 2 Bike Rack with Wheel Mount Cradles, Part Number S102. Now to begin our test fit, we'll slide the bike rack shank into the hitch, line up the hitch pin hole, and slide the hitch pin in. We can then move to the back of the shank where we can tighten that down securing the bike rack to the vehicle. We'll now and go ahead, and give you a few measurements. Our ground clearance here at the bottom of the bike rack is 11 inches and from the closest point of the bike rack with the bike rack in the stored position to the back of the vehicle measures 2-1/2 inches. We'll now go ahead and pull the handle and unfold the platform.
Kuat NV Hitch Bike Rack Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna, well be test fitting the Kuat Aluminum Hitch Mounted Two Bike Rack with Wheel Mount Cradles. This is the Kuat NV, part number N101. To being our test fit, well slide the bike rack shank into the hitch, line up the hitch pin holes and slide the hitch pin in. Well then move to the back of the shank and tighten the anti-rattle knob down securing the bike rack to the vehicle. With that done, well go ahead and give you a few measurements. Our ground clearance here at the bike rack measures ten inches.
Hidden Hitch Ball Mount with 4 Inch Drop Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna, well be test fitting the Hidden Hitch Ball Mount with four and three quarter inch rise or six inch drop rated at 6,000 pounds, part number 80240. Now to begin, well first need to get our hitch height measurement. To get that measurement, well measure from the top of the receiver tube to the ground. On this hitch, that measurement is 11 and three quarter inches. Now keep in mind that measurement can change due to hitch style, tire size or any accessories that may change your vehicles ride height, so its a good idea to measure yours. Well not go ahead and put our ball mount into the hitch, lining up the hitch pin and installing our pin and clip securing the ball mount to the vehicle.
Draw-Tite Ball Mount Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna, well be test fitting the Draw-Tite Ball Mount with three quarter inch rise or two inch drop rated at 6,000 pounds, part number 2923. Now before installing our ball mount, well first need to get our hitch height measurement. To do this, well measure from the inside top edge of the receiver tube to the ground. Now on this vehicle that measurement is 11 and three quarter inches. Now keep in mind that measurement can change due to hitch style, tire size or any other accessories which may change your vehicles ride height, so its a good idea to measure yours. Well now slide the ball mount shank into the hitch, line up the hitch pin hole and install our hitch pin and clip and with that our ball mount is secured to the vehicle in the drop position.
Convert-A-Ball Ball Mount with 2 Inch Drop Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna, well be test fitting the Convert-A-Ball Cushioned Ball Mount for 2 Inch Hitches with three quarter inch rise or two inch drop. This ball mount is rated for 10,000 pounds. Part number AMSC2. Now to being our test fit well need to get our hitch height measurement. To do this well measure from the inside top edge of the receiver tube to the ground. Now on this vehicle that measurement is 11 and three quarter inches.
Trailer Hitch Installation - 2007 Toyota Sienna - Curt
Today on our 2007 Toyota Sienna, we'll be installing the Curt Hitch, part number C13105. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch such as a drawbar, a bike rack, or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 4 inches. From the top of the receiver tube to the ground is 10-1/4 inches. Now, let's go ahead with the installation.
Trailer Hitch Installation - 2007 Toyota Sienna - Curt
Today on our 2007 Toyota Sienna, we'll be installing the Curt Hitch, part number C12065. This is what our hitch will look like once it's installed on the vehicle. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch such as the bike rack or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 3-1/2 inches. From the top of the receiver tube to the ground is 10-1/4 inches. Now, let's go ahead with the installation.
Trailer Hitch Installation - 2007 Toyota Sienna - Hidden Hitch
Today on our 2007 Toyota Sienna, we'll be installing Hidden Hitch, part number 87415. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for the new hitch such as a drawbar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/2 inches. From the top of the receiver tube to the ground is 9-3/4 inches. Now, let's go ahead with the installation.
Trailer Hitch Installation - 2007 Toyota Sienna - Draw-Tite
Today on our 2007 Toyota Sienna, we'll be installing the Draw-Tite Hitch, part number 75149. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch such as the drawbar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/2 inches. From the top of the receiver tube to the ground is 9-3/4 inches. Now, let's go ahead with the installation.
Trailer Hitch Installation - 2012 Toyota Sienna - Curt
Today on our 2012 Toyota Sienna well be installing the Curt Hitch part number C12065. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 4 inches. From the top of the receiver tube to the ground is 10 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Trailer Hitch Installation - 2012 Toyota Sienna - Hidden Hitch
Today on our 2012 Toyota Sienna well be installing the Hidden Hitch part number 87586. This is what our hitch will look like once its installed, next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 4 inches. From the top of the receiver tube to the ground is 10 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier. Now lets go ahead with the installation.Youll first need to remove the underbody trim panel.
Trailer Hitch Installation - 2012 Toyota Sienna - Draw-Tite
Today on our 2012 Toyota Sienna well be installing the Draw Tite Hitch part number 75696. This is what our hitch will look like once its installed, next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 4 inches. From the top of the receiver tube to the ground is 10 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier. Now lets go ahead with the installation.Youll first need to remove the underbody trim panel.
Yakima DoubleDown Ace Hitch Bike Rack Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna well be test fitting the Yakima DoubleDown Ace 4, part number Y02451. To mount our carrier to the vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up our hitch pin holes and use our securing pin to attach the bike rack. Then well use the hand knob at the base of the rack to tighten up and engage our anti-rattle lock. Now well go over a handful of clearance measurements. Weve got about 10 inches of ground clearance and about 3 inches of clearance between the closest part of the carrier and the closest part of the vehicle.
Thule Hitching Post Pro Hitch Bike Rack Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna, we'll be test fitting the Thule Hitching Post Pro Hitch Mounted Bike Carrier, part number TH934XTR. To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of the hitch. We'll line up our hitch pin hole, thread in our anti-rattle bolt, and tighten it down using a wrench. Next, we'll go over a handful of clearance measurements. We've got about 10 inches of ground clearance and about 5 inches of clearance between the closest part of the carrier and the closest part of the vehicle. Overall, we've added about 15 inches of length to the rear of the vehicle.
Yakima SwingDaddy 4 Hitch Bike Rack Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna, we'll be test fitting the Yakima SwingDaddy 4 Hitch Mounted Bike Carrier, part number Y02422. To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of the hitch. We'll line up our hitch pin hole, thread in our anti-rattle bolt and tighten it down using a wrench. Next, we'll go over a handful of clearance measurements. We've got about 10 inches of ground clearance and about 1/2-inch of clearance between the closest part of the carrier and the closest part of the vehicle. Overall, we've added about 10 inches of length to the rear of our vehicle with the carrier's arms folded down.
Yakima HighLite 2 Hitch Bike Rack Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna, we'll be test fitting the Yakima HighLite Aluminum 2 Bike Carrier, part number Y02438. To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of the hitch. We'll line up the pin holes and secure our biker rack with the pin, then we'll use the hand knob at the base of the bike rack to tighten up the anti-rattle wedge. Now, we'll go over a handful of clearance measurements. We've got about 10 inches of ground clearance and about 3 inches of clearance between the closest part of the carrier and the closest part of the vehicle. Overall, we've added about 11 inches of length to the rear of the vehicle with the carrier arms folded down.
Swagman Titan Hitch Bike Rack Review - 2012 Toyota Sienna
Today on this 2012 Toyota Sienna well be test fitting the Swagman Titan 4 hitch mounted bike carrier, part number S63410. To mount the carrier to the vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up our hitch pin holes, thread in our anti-rattle bolt, and tighten it down using a wrench. Next well go over a handful of clearance measurements. Weve got about ten inches of ground clearance and about seven inches of clearance between the closest part of the carrier and the closest part of the vehicle. Overall weve added about 18 inches length to the rear of our vehicle with the carrier arms folded down.
Surco Hitch Cargo Carrier Review - 2012 Toyota Sienna
Today on our 2011 Toyota Sienna well be test fitting the Surco 24 inch by 60 inch cargo carrier, part number 52018. To mount this carrier to our vehicle well insert the shank of the carrier into the receiver tube of our hitch. Well line up the hitch pin holes and secure the carrier with the standard five eighths inch pin and clip. Now well go over a handful of clearance measurements. Weve got about 12 inches of ground clearance at the rear of our cargo carrier and about a half an inch of clearance between the closest part of the carrier and the closest part of our bumper. Overall weve added about 26 and a half inches of length to the rear of our vehicle.
SportRack Escape 3 Hitch Bike Rack Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna well be test fitting the Sportrack Escape 3 hitch mounted bike carrier, part number A30403. To mount the carrier to the vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up our hitch pin holes, thread in our anti-rattle bolt, and tighten it down using a wrench. Next well go over a handful of clearance measurements. Weve got about ten inches of ground clearance and about four inches of clearance between the closest part of the carrier and the closest part of the vehicle. Overall weve added about nine inches length to the rear of our vehicle with the carrier arms folded down.
Softride Dura Hitch Bike Rack Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna were test fitting the Sortride Dura parallelogram, part number SR26247. To mount our carrier to the vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up our hitch pin hole, thread in our anti-rattle bolt, and then tighten it down using a wrench. Well then secure a lock over the end of the bolt. Now we want to prepare to load a bike. Well undo the rubber straps at the cradle thats closest to the vehicle and grab our bicycle.
Rola Hitch Cargo Carrier Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna well be test fitting the Rola 23 inch by 56 inch railed cargo carrier, part number 59502. To mount our carrier to the vehicle well insert the shank of the carrier into the receiver tube of the hitch, well line up the hitch pin holes and secure the carrier with the standard five eighths inch pin and clip. Next well go over a handful of clearance measurements. Weve got about 15 and a half inches of ground clearance at the rear of the carrier, about six and a half inches of clearance between the closest part of the carrier and the closest part of our vehicle. Overall weve added about 30and a half inches of length to the rear of the vehicle. Weve got about 14 inches of space between our tail pipe and the closest part of the carrier.
Pro Series Q-Slot Hitch Bike Rack Review - 2012 Toyota Sienna
Today, on our 2012 Toyota Sienna, we'll be test fitting the Pro Series Q-Slot Platform Style Bike Carrier, part number PS63134. To mount the carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of our hitch. We'll line up the hitch pinhole and secure the carrier with a pinning clip. Next, we'll go over a handful of clearance measurements. We've got about 10 and half inches of ground clearance and about five and half inches of clearance between the closest part of the carrier and the closest part of the vehicle. Overall, we've added about 22 inches of length to the rear of our vehicle.
Pro Series Eclipse 4 Hitch Bike Rack Review - 2012 Toyota Sienna
Today, on our 2012 Toyota Sienna, we'll be test fitting the Pro Series Eclipse 4 hitch mounted bike carrier, part number 63124.To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of the hitch. We'll line up our hitch pine hole, thread in our anti-rattle bolt and tighten it down using a wrench.Next, we'll go over a handful of clearance measurements. We've got about 10 inches of ground clearance and about 3 inches of clearance between the closest part of the carrier and the closest part of the vehicle. Overall, we've added about 30 inches of overall length to the rear of the vehicle.Now, we want to check for rear vehicle access. We'll remove the pin at the base of the bike carrier and tilt it down. We want to see if we can open up our hatch door all the way and access the cargo area even with the bike rack installed.Now, we can put our bike rack back up and prepare to load a bike.
Pro Series Hitch Cargo Carrier Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna, well be testing the Pro Series 24 inch by 60 inch Railed Cargo Carrier for 2 inch hitches, part number 63153. To mount our carrier to the vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well add up our hitch pin holes and then secure the carrier with a standard 5/8ths pin and clip. Now well go over some clearance measurements. Weve got about 16 inches of ground clearance at the rear of the carrier and about 7 inches of clearance between the closest part of the bumper and the closest part of the carrier. Overall, weve added about 33 inches of length to the rear of our vehicle.
Draw-Tite Ball Mount Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna well be test fitting the Draw Tite Ball Mount, part number 2923. First we want to go over measurement on the vehicle. We want to measure the hitch height. Thats from the ground to the inside top edge of our receiver tube. Keep in mind that this measurement will differ depending on exact model, tire size or any aftermarket add ons. The hitch height on our particular Sienna with this particular hitch measures in at 12 inches.
Trailer Hitch Installation - 2011 Toyota Sienna - Hidden Hitch
Today, on our 2011 Toyota Sienna, we'll be installing Hidden Hitch, part number 90214. Now, before we begin our installation, here's what your hitch will look like on the vehicle. We'll go ahead and give you a few measurements to help you in selecting accessories such as a bike rack or a cargo carrier. From the center of the hitch bin hole to the outermost part of the bumper is four and a half inches, and from the top of the receiver tube to the ground is 11 inches. Now, let's go ahead with our install. To begin the installation, we'll need to remove the plastic appearance panel which covers the trunk pan.
Trailer Hitch Installation - 2011 Toyota Sienna - Draw-Tite
Today, on our 2011 Toyota Sienna, we'll be test fitting Draw-Tite hitch, part number 36513. Now, before we begin our installation, here's what your hitch will look like on the vehicle. We'll go ahead and give you a few measurements to help you in selecting accessories such as a bike rack or a cargo carrier. From the center of the hitch bin hole to the outermost part of the bumper is four and a half inches, and from the top of the receiver tube to the ground is 11 inches. Now, let's go ahead with our install. To begin the installation, we'll need to remove the plastic appearance panel which covers the trunk pan.
Curt Folding Hitch Cargo Carrier Review - 2012 Toyota Sienna
Today, on our 2012 Toyota Sienna, we'll be test fitting the Curt 24 inch x 60 inch folding cargo carrier, part number C18132. To mount our carrier to the vehicle, we need to insert the shank of the carrier into the receiver tube of the hitch. We'll line up our hitch pinhole and we'll secure the carrier with the standard 5/8 pinning clip. We won't be able to use the carrier in the folded-up position due to inadequate clearance for the bumper. Now, we'll go over some clearance measurements. We've got about 18 and a half inches of ground clearance at the rear of the carrier and about 10 inches of clearance between the closest part of the carrier and the closest part of the bumper.
Curt 20x60 Folding Aluminum Cargo Carrier Review - 2012 Toyota Sienna
Today, on our 2012 Toyota Sienna, we'll be test fitting the Curt folding aluminum cargo carrier, part number C18100. Now, there's not enough bumper clearance to use this carrier in its upright position so we'll just use it as a flat carrier. To mount the carrier to the vehicle, we'll insert the shank into the receiver tube of the hitch, line up the hitch pinholes and secure the carrier using a standard 5/8-inch pinning clip. Next, we'll go over some clearance measurements. We've got about 13 inches of ground clearance at the rear of the carrier and about six inches of clearance between the closest part of the carrier and the closest part of the bumper. Overall, we've added about 26 inches of length to the rear of our vehicle.
Trailer Hitch Installation - 2011 Toyota Sienna - Hidden Hitch
Today, on our 2011 Toyota Sienna, we'll be test fitting Hidden Hitch, part number 87586. Now, before we begin our installation, here's what your hitch will look like on the vehicle. We'll go ahead and give you a few measurements to help you in selecting accessories such as a draw bar, a bike rack or cargo carrier. From the center of the hitch bin hole to the outermost part of the bumper is five inches, and from the top of the receiver two to the ground is 12 inches. Now, let's go ahead with our install. To begin the installation, we'll need to remove the plastic appearance panel which covers the trunk pan.
Trailer Hitch Installation - 2011 Toyota Sienna - Draw-Tite
Today on our 2011 Toyota Sienna, we'll be test fitting Draw-Tite Hitch, part number 75696. Now before we begin our installation, here is what your hitch will look like on the vehicle. We'll go ahead and give you a few measurements to help you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outermost part of the bumper is 5 inches, and from the top of the receiver tube to the ground is 12 inches. Now, let's go ahead with our install. To begin the installation, we'll need to remove the plastic appearance panel which covers the trunk pan.
Curt Hitch Cargo Carrier Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna, we'll be test fitting the Curt 20-inch by 48-inch cargo carrier, part number C18145. To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of the hitch. We'll line up our hitch pin hole, thread in our anti-rattle bolt, and tighten it down using a wrench. Next, we're going to go over a handful of clearance measurements. We've got about 11-1/2 inches of ground clearance and 1 inch of clearance between the closest part of the carrier and the closest part of the bumper. Overall, we've added about 21 inches of length to the rear of our vehicle.
Convert-A-Ball Ball Mount with 4 Inch Drop Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna, we'll be test fitting the Convert-A-Ball Cushion Ball Mount, part number AMSC4. First, we want to go over measurement on the vehicle. We want to measure the hitch height. That's from the ground to the inside top edge of our receiver tube. Keep in mind that this measurement will differ depending on exact model, tire size or any aftermarket add-ons. The hitch height on our particular Sienna with this particular hitch measures in at 12 inches.
Convert-A-Ball Ball Mount with 2 Inch Drop Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna, we'll be test fitting the Convert-A-Ball Cushion Ball Mount, part number AMSC2. First, we want to go over measurement on the vehicle. We want to measure the hitch height. That's from the ground to the inside top edge of our receiver tube. Keep in mind that this measurement will differ depending on exact model, tire size, or any aftermarket add-ons. The hitch height on our particular Sienna with this particular hitch measures in at 12 inches.
Trailer Wiring Harness Installation - 2006 Toyota Sienna
Today on this 2006 Toyota Sienna were going to install part number 118304 from Tow Ready. To start our install well open up the back hatch and then well go ahead and remove both taillights. Well also remove the vehicles rear threshold and then well also have to loosen up the side panels as well to get access to the wiring. On the passengers side well have to get through the jack storage compartment to get access to the wiring. At this point we can go ahead and start installing the T connector. Well start on the passengers side and run the wire with the red and green up to the passengers side taillight.
Trailer Hitch Installation - 2006 Toyota Sienna - Curt
Today on this 2006 Toyota Sienna were going to install part number C13105 from Curt. This is what the hitch looks like once its installed on the van. Next well give you some measurements to help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground is going to be 10 and three quarter inches. From the center of the hitch pin hole to the edge of the bumper is going to be four and a half inches. Now Ill go ahead and show you how the hitch is installed.
Husky Third Row Floor Liner Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna, we'll be test-fitting the WeatherTech FloorLiner inthe third row, part number WT460873, grey in color. This application is also availablein tan, part number WT450873, and black, part number WT440873. First, we'll remove the old or manufacturer's floor mat and we're ready to install theWeatherTech floor liner. WeatherTech liners are custom molded precisely to fit thevehicle and stay in place. Their shape, channels and moldings all work to keep dirtand debris contained in the liner and off of the carpeting. As you can see here, itscustom molded, raised outer lip will really trap in the dirt, dust and debris.
WeatherTech Cargo Floor Liner Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna, well be testing the WeatherTech Floor Liner in the rear cargo area, part number WT40238, black in color. This application is also available in tan, part number WT41238, and gray, part number WT42238. First, well go ahead and remove the old or manufactured floor mat, but for this application, there is none to remove. Now, were ready to install the WeatherTech Floor Liner. The WeatherTech Floor Liner is custom molded to stay in place. The shape, channels, and moldings all work to keep dirt and debris contained in the liner and off of the carpeting.
Thule MOAB Roof Top Cargo Basket Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna we'll be test-fitting the Thule Moab Rooftop Cargo Carrier, part number TH690. Now our vehicle's already equipped with a roof rack system, so we're ready to begin installing the basket. We'll place the basket on top of the crossbars where we'll then center it with the vehicle. Once we have the basket where we want it on the vehicle we'll use the included hardware to go underneath the crossbars and clamp it to the vehicle. With all our hardware tight our basket is clamped to the vehicle. We can then install the hardware covers and with the covers installed our basket is secured to the vehicle and we're ready to load it up.
SportRack Aero Roof Cargo Box Installation - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna we'll be test-fitting the SportRack Aero XL Cargo Box, part number A90275. To begin our test-fit we'll simply place our cargo box on top of our crossbars and line up the holes in the cargo box with our crossbars. We'll now go ahead and center the box with the vehicle. We can then take the included hardware, putting the metal U-clamp underneath the crossbars and securing it with the included wing nuts. And with all four clamps in place and tight our cargo box is secured to the vehicle and we're ready to load it up. One quick measurement, the cargo box will add 23 inches of height to the vehicle from the roof line.
WeatherTech Front Floor Liners Review - 2006 Toyota Sienna
Today on our 2006 Toyota Sienna we'll be test-fitting the WeatherTech Floor Liner in the front row, part number WT450871, tan in color. This application is also available in gray, part number WT460871 or black, part number WT440871. First we'll go ahead and remove the old or manufacturer floor mats. Now we're ready to install the WeatherTech Floor Liner. As you can see the WeatherTech liners are custom-molded to stay in place. The shape, channels and moldings all work to keep dirt and debris contained in the liner and off of the carpeting.
WeatherTech Front Floor Liners Review - 2012 Toyota Sienna
Today on our Toyota Sienna we'll be test fitting the weathertech front floor liners, part number WT463001 in gray. These liners are also available in tan, part number WT453001 and black, part number WT443001. Now to begin the installation, well need to remove the factory old floor mats if equipped from the vehicle. We can then take the new weathertech floor liners and place them onto the floor allowing them to conform to your vehicles floorboard. The custom molding ensures a perfect fit for each Toyota Sienna. The unique material is designed for strength and features and texture that securely grips the floor.
Thule XB16 Snow Tire Chains Review - 2012 Toyota Sienna
Today on our 2012 Toyota Sienna with tire size P23560R17 well be installing the Thule standard snow tire chains part number TH0157124. These great rust resist tire chains have D-shaped links for excellent tire traction in snow and ice. Now to begin our installation well need to remove the chains from their packaging, lay them out on the floor and go ahead and get any tangles from out of the chains. With that, done well now take the blue cable and slide it behind the tire from the rear toward the front of the vehicle. Here on the outside well grab both ends of the blue cable, bring it up around the tire and connect it together. Well then allow the blue cable to move behind the tire while we take the chains and drape them over the tread making sure they stay center with the tread.
Trailer Hitch Installation - 2012 Toyota Sienna
Alright, today on this 2012 Toyota Sienna were going to install part #: c13105 from Curt. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories such as a Inaudible, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outside edge of the bumper will be 5 and a half inches. And from the top of the receiver opening down to the ground will be 12 inches. Now well go ahead and show you how the pitch is installed.
Trailer Wiring Harness Installation - 2012 Toyota Sienna
Alright, today on this 2012 Toyota Sienna were going to install part #: 118498 from Tow Ready. First thing we need to do is open up the back hatch, get access to the hardware that holds the taillight set. Remove the hardware here and here. Through the taillight well pry out here on top and the sides and that will pop out. This little guide right here, that makes you pull out towards the back. Theres also a little pin right here.
Yakima Holdup Hitch Bike Rack Review - 2012 Toyota Sienna
Alright, today on this 2012 Toyota Sienna, were going to do a test fit of part number Y02433 from Yakima. This is their Holdup 2 Bike Carrier. One thing to know about this bike rack, is that its designed for 2-inch receivers only. Now, well go ahead and install off our test fit by installing the bike rack into the hitch, then well go ahead and tighten down the anti-rattle bolt and put the safety pin on the other side. Now, well go ahead and do a couple of clearance measurements. As its closest point to the bumper, were looking at 1/2 inch.
Thule Vertex 4 Hitch Bike Rack Review - 2012 Toyota Sienna
Alright, today on this 2012 Toyota Sienna were going to do a test fit of part #: th9029 from Thule, the Vertex 4 bike carrier. A few things to know about this bike rack, that it will work with inch and a quarter receiver hitches both class 1 and class 2, but when you use a bike rack with class 1 receiver hitch you are limited to carrying only two bicycles. This will also work with 2 inch receiver hitch with the included spacer and thats what well be using today. To start off our test fit well slide the bicycle rack into the hitch and then well go ahead and tighten down the anti-rattle bolt. Okay, now well go ahead and get some clearance measurements. Clearance between the bike rack and the bumper will be inch and 3/4.
Thule Parkway 2 Hitch Bike Rack Review - 2012 Toyota Sienna
Alright, today on this 2012 Toyota Sienna were going to do a test fit of part #: th958 from Thule, the Parkway 2 bike carrier. One thing to note about this bicycle rack, it is designed for 2 inch receiver hitches only. Now well start off our test fit by installing the bike rack into the hitch, then well go ahead and tighten down the anti-rattle bolt. Alright, now well go ahead and get some clearance measurements. Clearance from the bike rack to the bumper is going to be half an inch. And ground clearance looks like 9 and a quarter inches.
Thule Helium Hitch Bike Rack Review - 2012 Toyota Sienna
Today on this 2012 Toyota Sienna were going to do a test fit of part #: th970xt from Thule, this is our Helium bike carrier. Couple of things to know about this bicycle rack, that it will work with inch and a quarter receiver hitches both class 1 and class 2. This will also work with 2 inch receiver hitches like were going to use today with the provided spacer. Alright, well start off our test fit by installing the bike rack into the hitch, well install the pin, its keyed, so well give it a little bit of turn and pull back to put some tension on it. Then well go ahead and tighten down the anti-rattle knob. Alright, now well go ahead and get some clearance measurements.
Thule Apex 4 Swing Hitch Bike Rack Review - 2012 Toyota Sienna
Alright, today on this 2012 Toyota Sienna were going to do a test fit of part #: th9027 from Thule, the Apex swing forward bike carrier. One thing to know about this bicycle carrier that it is designed for 2 inch receiver hitches only. Well go ahead and start off our test fit by installing the bike rack into the hitch. Well make sure that the integrated hitch pin is secured into the hitch pinhole. Well go ahead and pull it back, take up some slack and then well go ahead and tighten down the anti-rattle know. Alright, now well go ahead and get some clearance measurements.
Thule Apex 4 Hitch Bike Rack Review - 2012 Toyota Sienna
Alright, today on this 2012 Toyota Sienna, we're going to do a test fit of part number TH9025 from Thule, the Apex 4 Bike Carrier. A couple of things to know about this bike carrier, that it will work with 1-1/4-inch receiver hitches, both class 1 and class 2. However, these who have a class 1 receiver hitch, you're only limited to carrying two bikes. This will also work with 2-inch receiver hitches as we're going to do today with the included spacer. We'll start off our test fit by installing the bike rack into the hitch. We'll make sure that the integrated hitch pin goes to the hitch pinhole and then we'll go ahead and tighten down the anti-rattle knob.
Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2012 Toyota Sienna
Alright today on this 2012 Toyota Sienna we're going to do a test fit of part no S64670 from Swagman, this is the Swagman XTC2 bike carrier. A few this to note about this bicycle rack that it will work with an inch and 1/4 receiver hitches both class 1 and class 2 and it will also work with a 2 inch receiver with the provided spacer. And our vehicle today has a 2 inch receiver installed. Okay to start off the test fit, we will install the bike rack into the hitch and then tighten down the anti retal bolt then install the clip on the other side. Alright now we'll go ahead and install the bike rack and get some clearance measurements. Clearance from the bike rack to the bumper will be 3 and 3/4 inches.
SportRack EZ Hitch Bike Rack Review - 2012 Toyota Sienna
Alright today on this 2012 Toyota Sienna we're going to do a test fit of part no. A30901. A few things to note about this bike rack that it will work of an inch and 1/4 receiver hitches both class 1 and class 2. It will also work with 2 inch receiver hitches with the included spacer. We will be working with the 2 inch receiver hitch today. Alright we will go ahead and start our test fit by installing the bike rack into the hitch and we will go ahead and tighten down the anti-retal bolt and put the safety pin on the other side.
SportRack Evader Hitch Bike Rack Review - 2012 Toyota Sienna
Alright today on this 2012 Toyota Sienna, we're going to do a test fit of part no 830403XT from Sportrack. This is the Evader 3 bike carrier. A few things to note about this bicycle rack that it will work with an inch and 14 receiver hitches class 2 only. This will also work with a 2 inch receiver hitch with the included spacer and that is what we will be working with today. We will start off our test fit by installing the bike rack into the hitch and then we will go ahead and tighten down the anti retal bolt and then install a safety clip on the otehr side. Alright with our bike rack installed let's go ahead and get some clearance measurements.
Yakima RailGrab Roof Rack Installation - 2005 Toyota Sienna
Today on this 2005 Toyota Sienna were going to be test fitting a Yakima Railgrab Roof Rack System. We already have our crossbar assemblies put together, so now were ready to mount them up on the vehicle. Since this system is designed to be used on vehicles with factory raised side rails, theres no specific crossbar spread we need to use. However, the maximum that Yakima recommends is 56 inches, so we want to make sure that we dont exceed this measurement. You also want to check the instructions in the accessories youll be using to see fit they require a specific crossbar spread and set up accordingly. The first thing well do is place the front crossbar assembly on top of our factory raised siderails.
Yakima FlipSide 4 Hitch Bike Rack Review - 2005 Toyota Sienna
Today on this 2005 Toyota Sienna minivan well go ahead and do a test fit of part number Y02426 from Yakima. This is a flipside four bike carrier. Lets start off by installing our rackinto a two inch receive r hitch. This rack will also fit an inch and a quarter receiver hitch, Class II only. It will work with a two inch receiver hitch with the bushing that we will be using today. Well slide it in and install the inaudible 0:00:23:5 and then well tighten it down, then well go ahead and put the safety pin in.
Thule Helium Hitch Bike Rack Review - 2005 Toyota Sienna
Today in its 2005 Toyota Sienna, we're going to do a test of part number TH970XT from Thule. This is Thule Aluminum Helium 2 Bike Carrier. We'll start up by installing the rack into the 2" receiver hitch with the bushing already installed. This bike rack will also fit into the corner receiver hitches for Class 1 and Class 2. We'll go ahead and slide into the hitch (inaudible) to hitch pin holes. Now that the pin is keyed, so we need to install unto the bicycle rack and then turn it 90-degress and then pull back on the rack.
Rhode Gear Highway Hitch Bike Rack Review - 2005 Toyota Sienna
Alright today, on this 2005 Toyota Sienna, were going to fit test the part number RG8015220 from Rhode Gear. This is the Highway 2 Bike Carrier. Well start off the test fit by installing the bike rack onto Toyota siennas rear. Now this bike rack will fit inches according to the receiver hitches as well, class one and class two. Well slide the rack into the hitch and well install the anti-radial bolt and put it in place. Well install our safety clip on the other side of bolt and were good to go.
Yakima DoubleDown 5 Hitch Bike Rack Review - 2005 Toyota Sienna
Alright today on this 2005 Toyota Sienna, were going to do a test fit of part number y02425, Yakimas Doubledown 5 Bike Carrier. We will go ahead and install this in our 2 receiver hitch. This bicycle rack does have a 2 bushing installed on it already. You can use it on an inch and a 1/4, however you want to limit it to a class 2 receiver hitch. Lets go ahead and install the anti-rattle bolt as part of the rock steady hitch tongue. Now it does come with a tool to help tighten it down, however a inch wrench will actually work as well.
Thule Crossroad Roof Rack Installation - 2005 Toyota Sienna
Today on this 2005 Toyota Sienna with factory raised side rails; we are going to be installing a Thule Crossroad Roof Rack System. We already have our crossbar assemblies put together so now we are ready to begin mounting them on the top of our vehicle. With this roof rack system we can have a maximum crossbar spread of 59 inches. We do not need to use a specific crossbar spread, as this system is designed to work on top of factory raised side rails, however you may want to check with the instructions on whatever accessories you might be using to see if they have a recommended crossbar spread. First we are going to set the front crossbar assembly on top of our side rails. We are going to measure from the end of the crossbar foot to the seam of our factory raised side rails.
Rhino-Rack SXBS Roof Rack Installation - 2005 Toyota Sienna
Today we have a 2005 Toyota Sienna with factory raised side rails, and we are going to be test fitting a roof rack from Rhino-Rack, part number sxbs8. We already have our crossbar assemblies put together, so were ready to begin mounting them on the vehicle. Since this roof rack system is designed to attach to our factory raised side rails, there are no specific set of measurements that we need to use. However, you may want to check with the instructions of whatever accessories you are going to be using to see if you need to setup for certain crossbar spread. First we are going to set our crossbar assembly on top of our side rails, and set our position. Since we dont have any specific measurements we need to use we do need to make sure that the front cross bar runs perpendicular with our side rails.
SportRack EZ Hitch Bike Rack Review - 2005 Toyota Sienna
Alright today on a 2005 Toyota Sienna Mini-van, we are going to do a test of part number A30901, from SportRack. This is SportRacks 2 Bike easy Hitch Mounted Bike Rack. This bicycle rack will fit both 1-1/4 inches class one and class two hitches, and also class three hitches. On this test fit we will be using a class three receiver hitch. So we have the bushing in place, we will go ahead and slide it in. Next we will install the anti-rattle bolt, we will just go ahead and install it and thread it in.
Trailer Hitch Installation - 2005 Toyota Sienna
install-triler-hitch-2005-toyota-sienna-v82700 Today on this 2005 Toyota Sienna we are going to be installing Valley Hitch part number V82700. Before we get started with our hitch installation, we are going to go ahead and show you a couple of the final install dimensions which are going to help make choosing your hitch accessories a little bit easier. From the top of the receiver tube opening to the ground is going to measure 11-1/4 inches, and from the center of the pin hole to clear the rear edge of the bumper is going to measure approximately 6 inches. Now lets go ahead and move on to installation. Starting off up underneath the vehicle here we want to go ahead and point out the mounting holes where we are going to be using to install the trailer hitch. Looking over here at the drivers side frame rail, at the rear most section of our frame we have two existing weld nuts here, and if you follow forward theres a third existing weld nut, and we will be using those three for our attaching points for our trailer hitch, and its actually going to be the same on the passengers side of the vehicle as well.
Trailer Hitch Installation - 2005 Toyota Sienna
Today on this 2005 Toyota Sienna, we are going to be installing Valley hitch, part number V82700. Before we get started with our hitch installation, we are going to go ahead and show you a couple of the final install dimensions, which are going to make choosing your hitch accessories a little bit easier. From the top of the receiver tube opening to the ground is going to measure 11-1/4 inches, and from the center of the pin hole to clear the rear edge of the bumper is going to measure approximately 6 inches. Now lets go ahead and move on to our installation. 0:25
Thule Revolver 4 Hitch Bike Rack Review - 2011 Toyota Sienna
Today with our 2011 Toyota Sienna, we are going to show you the Thule Revolver 4 bike rack, part number TH964. We will take the bike rack and fit it into our hitch, lining up the pin hole on the rack with the pin hole on our receiver. Next we will attach the included anti-rattle pin and lock. At the lowest point of the Thule Revolver, there are about 8-1/2 inches of ground clearance. The Thule Revolver measures 7-1/2 inches to the center of the hitch pin hole to the back of the upright bar. This allows enough clearance to clear the back bumper and back fascia of our 2011 Sienna. 0:37
Yakima DoubleDown 5 Hitch Bike Rack Review - 2011 Toyota Sienna
Today on this 2011 Toyota Sienna we are going to show you the Yakima DoubleDown 5 bike hitch mounted carrier, part number Y02425. The DoubleDown 5 can be adapted to fit both 2 inch and 1-1/4 inch, class II hitches. On our Sienna we have a 2 inch class III hitch so we have our adapter installed. To mount the bike rack, we will fit it inside of our hitch and line up the hitch pin hole on our hitch with the threaded pin hole on the shank of our bike rack. We will take and thread the anti-rattle hitch pin into the hitch and through the shank of our bike carrier. And secure it on the side with the clip. 0:40
Yakima RailGrab Roof Rack Installation - 2011 Toyota Sienna
Today on this 2011 Toyota Sienna we are going to show you how to install a Yakima RailGrab roof rack system. Once you have the crossbars and towers assembled, we can go ahead and fit them on our Sienna. With the Sienna, we will be using the medium size claw one notch below the second hash mark. Once we have the crossbar in place and we made sure that our overhang is even, we can go ahead and tighten the system down. The black Allen head bolt will tighten the clamp against the side rail. The silver bolt will tighten the crossbars to our RailGrab towers. We will tighten both the driver and passenger side evenly, making sure that we do not bump our crossbar and move it out of alignment. Once we have tightened both bolts on both sides of the Sienna, we can go ahead and install our second crossbar. 0:47
Thule Crossroad Roof Rack Installation - 2011 Toyota Sienna
Today on this 2011 Toyota Sienna we are going to show you a Thule Crossroad roof rack system. The Thule Crossroad system is designed to attach to vehicles with factory raised side rails. It utilizes a steel band that is coated in rubber that wraps around the side rails. Once you have the roof rack system assembled, lay the first crossbar over the side rails. Once we have our crossbar in position, we will make sure that the bar is overhanging on either side evenly. Once we have made sure that the overhang is even on both sides, we can go ahead and begin tightening down our crossbar system. Take the steel band, pull it underneath the side rail and push it in to the crossroad foot. Take the cap with the built in Allen key and begin to tighten the clamp. We will move back and forth from driver side to passenger side to make sure we tighten down the system evenly. As we tighten the Allen head bolt, not only does it pull the steel band tight around the side rails but it also locks the Crossroad feet on to the crossbars. 1:02
Trailer Hitch Installation - 2011 Toyota Sienna
Today we are working on a 2011 Toyota Sienna. We are going to install Curt hitch part number C13105. Here are a couple of measurements that will assist you with ing accessories for your new hitch, such as a bike rack, a draw bar or cargo carrier. From the center of the hitch pin hole to the outermost point of the bumper is 5-1/4 inches. And from the top of the receiver tube to the ground is 11 inches. Now let us go ahead with the installation. 0:27
Trailer Wiring Harness Installation - 2011 Toyota Sienna
Today we will be working on a 2011 Toyota Sienna. We will be installing Tow Ready T-one connector part number 118498. We are going to start by accessing the rear cargo area of the van. And we need to remove both taillight assemblies. They are each mounted with two 10 millimeter bolts. You can see this gives us access to the rear taillight wiring. I am going to go ahead and disconnect the lens from them now. On each connection, there is a small locking tab that must be depressed before disconnecting. I am going to go ahead and set my taillight lens assembly aside for now. We will reinstall that later. Now I am going to go repeat the same process on the passenger side. Next we want to remove the three cargo hooks so that we can remove this rear threshold. I am going to repeat the same process for the next two. Now that we have our cargo hook hold downs removed, we can go ahead and remove the rear trim panel. We will set that out of our way. You can see it gives us access to route our wiring from the driver to the passenger side. 0:55
Trailer Hitch Installation - 2004 Toyota Sienna
Today on this 2004 Toyota Sienna we are going to install part number V82700 from Valley. This is what the hitch looks like when it is installed on the vehicle. And also right now we will give you some measurements on the hitch that will help you out in ing some accessories. From the top of the receiver opening down to the ground is going to be 10-1/2 inches. And from the center of the hitch pin hole to the outside edge of the bumper is going to be 7 inches. 0:24
Trailer Wiring Harness Installation - 2004 Toyota Sienna
Today on this 2004 Toyota Sienna we are going to install part number 118304 from Tow Ready. This is their T-One wiring harness. The first steps involved is to open up the rear tail gate of the vehicle because we have to get behind the tail lights so that means we are actually going to have to remove the two tail lights on the vehicle. First we will start off on the driver side and then we will go over to the passenger side. Pop this side loose a little bit and it will go sideways like this. Rock it back and forth. Then you will want to disconnect at the tail lights right here. There is a little tab you push down and it comes right apart. What we are going to do next is remove this rear threshold right here. 00:41
Trailer Hitch Installation - 2004 Toyota Sienna
Today on this 2004 Toyota Sienna we are going to install part number 87415 from Hidden Hitch. This also applies to part number 75149 from Draw-Tite. The first thing we need to do is lower the exhaust on the passenger side of the vehicle. We are going to spray down the exhaust hanger with some lubricant and we are going to back it off so we can lower our exhaust to get to our catching points. Push off the rubber hangers as best as you can. The next thing we will do is put a strap around the exhaust and pull it over to the side just a little bit so we have a straight shot at the attachment points. Now we can show you the three attaching points. They are going to be these threaded holes here, here, and here. If the vehicle has been around for a few years it is going to have some dirt and grime and corrosion up in those threads so right now is the best time to take a few minutes to clean out all of the threads in the van. 00:56
Trailer Wiring Harness Installation- 2005 Toyota Sienna
Today on this 2005 Toyota Sienna Van, we will be installing wiring harness part number 118304. The ports we are going to be plugging our wiring harness into are located directly behind the tail lights here at the rear of the vehicle. So the first thing we need to do is go ahead and remove both tail lights from the driver and passenger side. There are two inboard screws here that need to be removed and then we can pull the tail light right off. :24
Trailer Hitch Installation - 2005 Toyota Sienna
Today on this 2005 Toyota Sienna Mini Van we will be installing Hidden Hitch part number 87415. This installation will also apply to Draw-Tite part number 75149. We are underneath the vehicle, the first thing we want to do before we start our hitch installation is to lower the exhaust off its rear most hanger. That is going to give us a little bit more access room here on the passenger side. :21
Trailer Wiring Harness Installation - 1998 Toyota Sienna
Today we are going to install part number 43475 from Hoppy. This is their wiring kit and we are going to install on a 1998 Toyota Sienna mini van. The wiring plugs for this T connector are going to be located behind the plastic here. You can either: a, access them behind the tail light or take off the tail light and get to them that way and run them straight down. Or, in this case, we are going to go behind the plastic and install everything on the inside. First off, we are going to go ahead and take off the thresh hold right here so we can take out the side panels. Alright, undo a couple of screws for the panels. Take off this panel here and there is an additional screw back here you can loosen the panel, the whole rear interior quarter panel with.
Trailer Hitch Installation - 1998 Toyota Sienna
Today we are going to install part number 87638 from Hidden Hitch. And we are going to be installing this on a 1998 Toyota Sienna mini van. And this also applies for part number 75120 from Draw-Tite. To begin our install, we need to do a couple things. We need to lower the exhaust to help get it out of the way. Sometimes, you can sneak it between the bumper and tail pipe, but just to give you a little bit of extra working room, we will go ahead and lower it out of the way. And then also these tie-down hooks for shipping, these come off and stay off. And we will begin by removing these. Alright, at this point we can go ahead and install the hitch with the fasteners towards the end of the vehicle. And it is a good idea to have an extra set of hands with this one it is a little on the wide side. We will just temporarily install it with the bolts.
Trailer Wiring Harness Installation - 2008 Toyota Sienna
Today we are going to install part number 118304 from Tow Ready. On a 2008 on a Toyota Sienna Mini Van. The first thing we are going to do is remove the tail lights. We will start on the passenger side then work our way over to the driver side. To remove the tail light we have to push down on this pin and pull the connector out. We will go ahead and do the same thing for the other side. The next thing we need to do is to remove this trim panel here. There are 3 of these latches we have to remove all the way across from left to right. Once we have those 3 latches removed we can now take off this back part of trim panel. You have to pry it out and lift it up at the same time and it will come loose. Now at this point we need to pull this panel away.
