Select Your Vehicle

View Cart


Toyota Sequoia owners are most interested in these products

or change vehicle




Toyota Sequoia Videos

Trailer Hitch Installation - 2001 Toyota Sequoia - Draw-Tite

Today on our 2001 Toyota Sequoia, we're going to install part number 75126 from Drawtech 00:06. This is what the hitch looks like once it's installed on the vehicle. Next, we'll give you some measurements that'll help you out in selecting some accessories, such as the ball mount, a bicycle rack or a cargo carrier. From top receiver opening down to the ground, it'll be about 20 and 1/2 inches. From center of the hitch pin hole to edge of the bumper will be about 1 and 3/4 inches. One other thing to note is the hitch actually does go past the bumper about 3/4 of an inch. First thing we need to do for our install is go ahead and lower a spare tire. We need to remove it to help us install the hitch.



Trailer Wiring Harness Installation - 2001 Toyota Sequoia

Today, on our 2001 Toyota Sequoia, we'll be installing the Curt T Wiring Harness for a factory tow package. Part number C55246. We'll take a look under our vehicle and you can see where our port is connected right here. On this particular vehicle, a factory tow package plug is located on the driver's side, behind the body work this is all behind the bumper. It is connected to a cap that's attached to the body. Push down on the tab that holds the connector in place and we can go ahead and remove it. Then, we'll take our new part from Curt, and go ahead and plug it into the port.



Trailer Hitch Installation - 2001 Toyota Sequoia - Curt

Today on our 2001 Toyota Sequoia, we're going to install part number 13440. Now this is what our hitch looks like once installed on our vehicle. Next we'll give you some measurements to help you out in selecting accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground, will be about 20-1/2 inches. From the center of the hitch pin hole to the edge of the bumper, will be about 1-3/4 inches. One other thing to note is that the hitch actually does go past to the bumper about 3/4 of an inch.



Longview Custom Towing Mirrors Installation - 2005 Toyota Sequoia

Today on our 2005 Toyota Sequoia, we're going to be test fitting the long view slip on custom fit towing mirrors, part number CTM4000. With a hardware kit, we're going to have two curled hooks, two flat hooks, four knobs, two felt strips and two adapter pieces. The adapter pieces here may be mirror images of each other, or they may be identical. Either way, they'll still install on the vehicle. The first thing we need to do is apply the felt strips. First, we'll cut the felt strip and install it on the adapter that we'll be using on the driver side. We will install part of the felt here on the high ridge, and we'll take another piece and put it around the eye-lit on the top.



Yakima RocketBox Pro 11 Rooftop Cargo Box Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia, were going to be test fitting the Yakima RocketBox Pro 11 Rooftop Cargo Box, part number Y07193. With our vehicle already equipped with a full roof rack system and our box already preassembled, we can go ahead and set the RocketBox on top of the load bars. Once we have it in position on top of the load bars, well go ahead and open the lid and use the hand knobs to tighten down the clamps. This will secure the RocketBox to the load bars of our roof rack system. Now, we can go ahead and close our lid and were ready to hit the road. And that does it for the test fit of the Yakima RocketBox Pro 11 Rooftop Cargo Box, part number Y07193, on our 2012 Toyota Sequoia..



Yakima LoadWarrior Roof Cargo Basket Review - 2012 Toyota Sequoia

Today on this 2012 Toyota Sequoia, well be test fitting the Yakima LoadWarrior Roof Rack Cargo Basket, part number Y07070. With our basket already preassembled and our vehicle equipped with the manufacturers roof rack system, we can go ahead and set the basket directly into position on top of the roof rack. After we get the cargo basket on top of the rack and centered, well go ahead and use the clamps to secure the basket on the roof rack. At this time, well just run our fasteners down finger tight to secure the carrier on top of the rack. Now, well go ahead and make sure our basket is centered on the load bars and then well go back and tighten two of the fasteners to secure the basket to the roof rack. And there you have it.



Yakima SwingDaddy 4 Hitch Bike Rack Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia, well be test fitting the Yakima SwingDaddy 4 Bike Hitch Mounted Bike Rack, part number Y02422. Now to begin our test fit, well simply place the bike rack shank into the hitch, line up the hitch pin hole and tighten down our anti-rattle bolt. With our anti-rattle bolt tight, our bike rack is secured to the vehicle. Well now go ahead and give you a few measurements. Our ground clearance at the bike rack is 17-1/2 inches and from the closest point of the bike rack to the back of the vehicle is 6 inches. We can now pull the switch at the top of the bike rack mast to bring out our dual arms.



Yakima StickUp 2 Hitch Bike Rack Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia we'll be test fitting, part number Y02420, the Yakima Stickup, two bike, hitch mounted folding platform style bike rack. Now to begin our test fit we'll simply slide the bike rank shank into the hitch, line up the hitch pinhole and install our anti-rattle bolt. With our bolt tight our bike rack is secured to the vehicle. We'll now go ahead and give you a few measurements. Our ground clearance at the bike rack is 18 inches and from the closest point of the bike rack to the back of the vehicle is six inches. We'll now unfold the platform and open our cargo door.



Yakima Holdup Hitch Bike Rack Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia we are going to be test fitting the Yakima Holdup two hitch mounted bike rack for two inch hitches, part number Y02433. With our bike rack already pre-assembled and our vehicle equipped with a two-inch hitch, we'll go ahead and slide the bike rack shank directly into the receiver tube of the hitch lining up the hitch pinholes then we'll install and tighten down the anti-rattle bolt and lock. This is what the bike rack will look like on the vehicle in its stored position. Now we'll go ahead and take a few measurements. From the nearest point of the bumper to the nearest point of the bike rack is six inches. With the bike rack in the stored position we add an additional 14 inches to the overall length of the vehicle length and from the lowest point of the bike to the ground is 17-1/2 inches.



UWS Aluminum Cargo Carrier Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia we'll be test fitting the 23 by 51 Aluminum cargo carrier for two-inch hitches, part number UWS03511. Now to begin our test fit we'll simply slide the cargo carrier shank into the hitch, line up the hitch pinhole and install our hitch pin and that will secure our carrier to the vehicle. Now we'll go ahead and give you a few measurements. From the closest point of the cargo carrier to the bumper of the vehicle is 4-1/2 inches and this cargo carrier will add an additional 27-1/4 inches to the overall vehicle length. Now the exhaust exits the passenger rear on this vehicle and is approximately six inches from the cargo carrier platform. It also appears to be about two inches lower than the platform so there will be little to no heat transfer while you are driving down the road and that completes our test fit of the 23 by 51 Aluminum cargo carrier for two-inch hitches, part number UWS03511 on our 2012 Toyota Sequoia..



Pro Series Eclipse 4 Hitch Bike Rack Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia we'll be test fitting the Tow Ready, four-bike, hitch mounted bike rack, for two-inch hitches part number 63124. Now to begin our test fit we'll slide our bike rank shank into the hitch, line up the hitch pinhole and install our anti-rattle bolt. With our bolt tight, our bike rack is secured to the vehicle. We'll now go ahead and give you a few measurements. Our ground clearance at the bike rack is 17-1/2 inches and from the closest point of the bike rack to the back of the vehicle is 6-1/2 inches. Now we'll go ahead and pull the pin at the bottom of the bike rack mast to tilt the mast down.



Thule Vertex 4 Hitch Bike Rack Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia we are going to be test fitting the Thule Vertex four-bike carrier, part number TH9029. Now to begin our test fit we'll simply slide the bike rank shank into the hitch, line up the hitch pinhole and install our anti-rattle bolt. With our bolt tight, our bike rack is secured to the vehicle. Now we'll go ahead and give you a few measurements. Our ground clearance at the bike rack is 18 inches and from the closest point of the bike rack to the back of the vehicle is 4-1/2 inches. We'll now go ahead and pull the hitch switch at the bottom of the mast to bring the mast down and open our cargo door and as you can see we can gain full access to the cargo area with this bike rack.



Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia we are going to test fit the Thule SUP, taxi, part number TH810. With the vehicle equipped with the manufacturer's roof rack system and our carrier already pre-assembled we can go ahead and put it directly on the load bars of our roof rack system. For today's application we are going to go ahead and mount it in the center of the vehicle. Using the speed link universal mounting system, we can quickly and easily secure our carrier to the load bars. And there you have it, in just a few simple steps we've gone ahead and secured our carrier to the roof rack system. Now we are ready to hit the road and that does it for our test fit of the Thule Taxi Stand-Up Paddleboard Carrier, part number TH810 on our 2012 Toyota Sequoia..



Thule Parkway 2 Hitch Bike Rack Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia we'll be test fitting the Thule Parkway, two-bike carrier, part number TH958. Now to begin our test fit we'll simply slide the bike rank shank into the hitch, line up the hitch pinhole and install our anti-rattle bolt. With our bolt tight, our bike rack is secured to the vehicle. Now we'll go ahead and give you a few measurements. Our ground clearance at the bike rack is 17-1/2 inches and from the closest point of the bike rack to the back of the vehicle is four inches. Now we'll go ahead and pull the pin at the bottom of the bike rack mast to bring the mast down and open our cargo door and as you can see we can gain full access opening the cargo door completely with this bike rack.



Thule MOAB Roof Top Cargo Basket Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia we'll be test fitting the Thule MOAB Roof Top Cargo Carrier, part number TH690. With our vehicle equipped with the manufacturer's roof rack system and our cargo basket already pre-assembled we are ready to go ahead and install it on the top of the load bars of the vehicle. First, we'll install our fasteners to secure the clumps around the load bars. Once we install them, we'll just run them down finger tight. Next, we'll go ahead and center the cargo basket on the roofline of the vehicle. Now with our cargo basket centered up, we are ready to go ahead, and tighten and secure all of our fasteners.



Thule Hitching Post Pro Hitch Bike Rack Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia we'll be test fitting the Thule Hitching Post Pro, part number TH934 XTR. Now to begin our test fit we'll simply slide the bike rack shank into the hitch, line up the hitch pinhole and install our anti-rattle bolt. With our bolt tight, our bike rack is secured to the vehicle. Now we'll go ahead and give you a few measurements. Our ground clearance at the bike rack is 18 inches and from the closest point of the bike rack to the back of the vehicle is eight inches. Now we'll go ahead and pull the pin at the bottom of the bike mast to tilt the mast down.



Thule Helium Hitch Bike Rack Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia well be test fitting the Thule Helium Aluminum two bike carrier for both 1-1/4 and two inch hitches, part number TH970 XT. Now to begin our test fit will simply slide the bike rack carrier into the hitch using the included adapter for two-inch hitches, we can then line up the hitch pinhole and using the attached hitch pin, we'll insert it into our hitch pinhole. We can then tighten down the anti-rattle knob at the back of the bike rack. Now our bike rack is secured to the vehicle. With the bike rack secured to the vehicle we can now go ahead and give you a few measurements. Our ground clearance at the bike rack is 17-1/2 inches and from the closest point of the bike rack to the back of the vehicle is eight inches.



Pro Series Q-Slot Hitch Bike Rack Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia, we'll be test fitting the Pro Series Q-Slot platform style bike carrier, part number PS63134. Now to begin our test fit we'll simply place the bike rack shank into the hitch, we'll line up the hitch pinhole and install our hitch pin. With that our bike rack is secured to the vehicle. Our ground clearance at the bike rack is 21 inches and from the closest point of the bike rack to the back of the vehicle is 11 inches. We can now unfold the platform to open our cargo door and as you can see we can gain full access opening the cargo door completely with this bike rack. We are now almost ready to load our bike.



Curt Hitch Cargo Carrier Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia well be test fitting the Curt 20x48 cargo carrier for both 1 and 2 inch hitches part #: C18145. Now to begin our test fit well simply slide the cargo carrier shank into the hitch using the included adapter for the 2 inch hitch. With it in place well go ahead and install our anti-rattle bolt tightening it down. With the bolt tight our cargo carrier is secured to the vehicle. Now well go ahead and give you a few measurements. The closest point of the cargo carrier is 4 inches from the bumper and the cargo carrier will add an additional 2 feet to the overall length of your vehicle.



Thule Doubletrack Hitch Bike Rack Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia, we'll be test -fitting the Thule Doubletrack Platform Style 2-Bike Carrier, part number TH990XT. Now to begin our test-fit, we'll simply place the bike rack shank into the hitch. Line up the hitch pin hole, and install our anti-rattle bolt. With our bolt tight, our bike rack is secured to the vehicle. Now we'll go ahead and give you a few measurements. Our ground clearance at the bike rack is 16 and a half inches, and from the closest point of the bike rack to the back of the vehicle is seven inches.





Toyota Sequoia Questions

  • First you will need a set of crossbars for the roof of your 2012 Toyota Sequoia. This will allow a roof basket to attach to and then finally the Rhino Rack Cargo Basket # RRLBXL will attach to that. For a roof rack I would recommend the Thule AeroBlade Load Bars # THARB53B and the Thule Rapid Crossroad Roof Mounted Railing Foot Pack # TH450R. Then for a cargo basket large enough for the # RRLBXL I would recommend the Yakima MegaWarrior Extra Large Roof Rack Basket part #...
    view full answer...

  • I would recommend using 2 sections of Horizontal E-Track, # E19148, down each side and 2 sections of Horizontal E-Track down the middle of your trailer, 6 sections in all, to give you as many tie down options as possible for securing all of your different toys. Your BMW K1200 sounds like the heaviest item you will need to tie down. I recommend using 2 packages of the Retractable Ratchet Straps, # 34414, along with 4 of the E-Track Tie-Off Rings, # 59131. Four tie down points...
    view full answer...

  • To upgrade your 2002 Toyota Sequoia to a 7-Way RV style connector you will need to add a 4-Way to 7-Way adapter, like the Adapter 4 Pole to 7 Pole and 4 Pole, item # 37185. There is a 4-Way connector on the back of the adapter that you plug your existing 4-Way connector into, then you will need to hard wire the remaining wires. There is not a factory style 7-Way connector available for your model. The black is for 12 volt power and is connected to the vehicle battery through...
    view full answer...

  • Since your 2006 Toyota Sequoia came with a factory tow package, you can plug in the wiring harness, # 3040-P into the port on the vehicle. It is located under the dash to the left of and above the the emergency brake. You will remove the panel that is there on the far left, and the connector will be tucked up behind some other harnesses. It will have a white connector. I have included a link to a video that shows the installation of this harness on a similar vehicle. Make...
    view full answer...

  • If you have flush mounted rails that run front to back on your 2016 Ford Edge you would want the roof rack part numbers # THLB50, # TH460, and # THKIT4047. If instead you have a totally naked roof you would want the part numbers # Y00409, # Y00124, # Y00664, and # Y00731.
    view full answer...

  • I confirmed with my contact at StrombergCarlson that their Lend-a-Hand Folding RV Handrail, part # AC-300, and the similar aluminum version, part # AM-200, can both fold either to the left or to the right. These two products differ in that the AC-300 uses a stainless steel handle with aluminum mounting blocks that secure with 4 screws, while the AM-200 uses an aluminum handle and plastic mounting blocks that secure with 2 screws. Both products need to be mounted to a solid...
    view full answer...

  • I went out to the warehouse and pulled the E-Track Wood Beam Socket, # 59149, and I produced a short video showing the dimensions of the E-Track Wood Beam Socket and took some close up video so you can see how the wood beam socket works. There are 4 holes in the socket for attachment to 2X lumber. The two holes on the bottom are centered and positioned at 1/2 inch and 1-3/4 inches in from the inside of the bracket. The two holes in each side of the bracket are positioned at...
    view full answer...

  • When choosing a weight distribution system, you will want one with a tongue weight capacity range that encompasses the trailer tongue weight, loaded and ready to tow. Based on the research I did on the R-Vision Trail Sport 27QBSS, it has a gross trailer weight of about 6,000 pounds. Since trailer weight should be between 10 and 15 percent of the gross trailer weight, you would need a system with a range of 600 to 900 pounds. I recommend the Strait-Line Weight Distribution System...
    view full answer...

  • For your vehicle I have a couple of towing mirror recommendations, but the Longview Custom Slide On Towing Mirrors, part # CTM400, will not work on your 2005 Toyota 4Runner. The mirrors have a different outer construction that prohibits the use of the slide on towing mirror, part # CTM400. The Universal Clip-On Towing Mirror, part # 7070, is easy to install and remove, once the initial setup is done. I am including a link to a video review on this strap-on mirror. Another...
    view full answer...

  • Swagman has built several bike rack solutions specifically for the rear of Fifth Wheels, campers and trailers. Often times there is much more rear bumper bounce on a trailer or pop-up camper when compared to a passenger vehicle, so Swagman designed some bike racks to withstand the rougher ride. If the camper has a solid steel square tube bumper, you could use something like the Swagman Bumper Hitch, part # S64025 in conjunction with a towing bike rack like part # S64400. Swagman...
    view full answer...

  • According to the research I did, the 2007 Keystone Springdale 189FL had a dry weight of 4,185 pounds, a carrying capacity of 1,770 pounds, and a tongue weight of 455 pounds. If the trailer were loaded to capacity, it would weigh in at about 6,000 pounds. Since tongue weight should be between 10 and 15 percent of the gross trailer weight, that would put the tongue weight at a range of 600 to 900 pounds. When choosing a weight distribution system, you will want one that has a...
    view full answer...

  • The installation of the Tow Ready Replacement Multi-Plug 7-Way and 4 Pole Trailer Connector, part # 20137, is a pretty straightforward installation. The best way to determine this is to use a circuit tester, like part # 3808, and check the function of the 7-Way and 4-Way connectors without a trailer connected. This will eliminate the possibility that there is a wiring issue on the trailer causing the problem you are seeing. If the harness shows the same issue without the...
    view full answer...

  • In order for the brakes on your pop up trailer to function, you will need to install a brake controller. I would recommend a proportional brake controller, such as the Tekonsha Prodigy, part # 90185. A proportional controller will determine how quickly the tow vehicle is braking, and provide the proper voltage to the trailer brakes so that both vehicles stop at the same rate. To install the controller, we offer a Brake Controller Installation Kit, part # ETBC7 which includes...
    view full answer...

  • I checked with CIPA and they could not confirm the fit of the part # CM11300 on your 2008 Lexus GX 470 so I could not safely recommend them for you. The only safe option I could recommend would be a universal towing mirror option. I recommend the K Source Universal Clip-On Towing Mirror, part # KS3891 for your vehicle. As long as you have a lip on the edge of your mirrors, these will work great for you. These mirrors are sold individually and will attach to either the driver...
    view full answer...

  • There are a couple of ways you could add a 5-Way flat to your 2006 Toyota Sequoia. I recommend a more direct method. You can use the Adapter 4 Pole to 5 Pole Trailer Wiring Adapter, # 20036. One end plugs into the 5-Way on the boat trailer, the other end plugs into the 4-Way on the vehicle. The 4-Way end has an additional wire for the extra function that is on the 5-Way end. If the extra pin on the trailer is used for an electric reverse lockout, you would connect the blue...
    view full answer...

  • The chain hangar brackets on the Reese Strait-Line Weight Distribution System, part # RP66082 will attach to the frame at approximately 30 inches from the center of the trailer coupler to the center of the brackets. These brackets do install over the top of the frame. I am including a link to the installation instructions on the Reese WD system and a link to a video of a Reese WD system being installed. It will show how to measure to install the chain hangars. To attach the...
    view full answer...

  • We do have tire chains for both the 265/70R16 and 31x10.5R15 tires that you have. I have included a link to our tire chain fit guide main page. On the right hand side, you can input your tire size to bring up the chains that will fit. I have also included a link to our FAQ article on tire chains for you. Make sure to consult each vehicle owners manual for any recommendations or restrictions on the use of tire chains.
    view full answer...

  • Installation of a 4-Way wiring harness on a 2006 Toyota Sequoia requires a Upgraded Circuit Protected Modulite with 4 Pole Harness, item # 119179KIT. You will need to splice the wires from this kit into the wires behind the vehicle tail lights. You can then upgrade the 4-Way connector, at any time, by using the Brake Controller Installation Kit, item # ETBC7. This kit includes all of the extra wires, circuit breakers and connectors needed to complete the installation of a 7-Way...
    view full answer...

  • For your 2005 Toyota Sequoia towing a 24 foot travel trailer, I recommend the High Performance Reese SC Weight Distribution System with Shank, # RP66151. The RP66151 has a tongue weight capacity up to 600 pounds and it can handle up to 10,000 pounds of gross trailer weight. I looked up your trailer and found it to weigh around 4,500 pounds, so this system will work for your needs. I have included a link to the instructions below. This system comes with the shank but not a ball....
    view full answer...

  • As far as the lighting functions, harness # 20137 and # HM43385 are going to be the same. It is the other three functions (reverse lights, electric brake output, and 12 volt power) that are slightly different between the two. So as far as light functions only, either connector would work. You mentioned a relay and fuse and there are likely other relays and fuses associated with the tow package wiring that you can check. Consult the 2003 Toyota Sequoia's owner's manual to find...
    view full answer...




Articles you may be interested in








Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email






etrailer.com reviews etrailer.com reviews

All images, layout and content copyright etrailer.com