Toyota FJ Cruiser owners are most interested in these products
change vehicle
Trailer Hitch Installation - 2013 Toyota FJ Cruiser - Hidden Hitch
Today on our 2013 Toyota FJ Cruiser, well be installing hidden hitch part number 87412. This is what our hitch will look like once it is installed. Next, well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole, the outermost edge of the rear mounted spare tire is 8-3/4 inches. From the top of the receiver tube opening to the ground is 18-1/2 inches. This will assist you in selecting accessories such as a ball mount, a bike rack, or cargo carrier.
Trailer Hitch Installation - 2013 Toyota FJ Cruiser - Draw-Tite
Today, on our 2013 Toyota FJ Cruiser we will be installing the Draw-Tite hitch part #75461. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. On the center of the hitch pin hole, the outermost edge of the rear-mounted spare tire is eight and three-quarter inches. From the top of the receiver tube opening to the ground is eighteen and one-half inches. This will assist you with selecting accessories such as a ball mount, a bike rack or a cargo carrier.
Rain-X Weatherbeater Wiper Blades Installation - 2007 Toyota FJ Cruiser
Today on this 2007 Toyota FJ Cruiser well be installing the Rain-X weather beater wiper blades, drivers side part number RX30216 and the center and passenger side wiper part number RX30214. To begin our install we will first need to remove the factory or previously installed wiper blades. This vehicle is equipped with a J hook style wiper arm. You will need to push the black button located inside of the J and push the wiper blade down towards the base of the wiper arm. This will allow the wiper to slide free. Lets take our new Rain-X weather beater wiper blade and slide the wiper into the opening of the J hook.
Putco PURE Light Installation - 2007 Toyota FJ Cruiser
Today on our 2007 Toyota FJ Cruiser well be installing the Putco Pure Premium 7443 LED bulbs, part number P237443R360. First well open up the rear cargo door. Then well remove the access panel behind the drivers side tail light assembly. Well be accessing the white wire connector and brown socket. This is for the tail light, stop lamp circuit. To remove the white wire connector youll press on the locking tab and then remove it from the socket.
Trailer Hitch Installation - 2008 Toyota FJ Cruiser - Hidden Hitch
Today on our 2008 Toyota FJ Cruiser well be installing Hidden Hitch part number 87412. Now, before we begin our installation here are a few measurements to help you when selecting accessories such as a drawbar, a bike rack, or Cargo area. From the center of the hitch pin hole to the outermost part of the spare tire is 9 inches. From the top of the receiver tube to the ground is 19-3/8 inches. Now lets go ahead with our install. Now, to begin our installation well need to drop our exhaust tail pipe down.
Trailer Hitch Installation - 2008 Toyota FJ Cruiser - Draw-Tite
Today on our 2008 Toyota FJ Cruiser we'll be installing Draw-Tite hitch, part number75461. Now, before we begin our installation here are a few measurements to helpyou when selecting accessories, such as a drawbar, a bike rack or a cargo carrier.From the center of the hitch pin hole to the outermost part of the spare tire is 9". Fromthe top of the receiver tube to the ground is 19-3/8". Now let's go ahead with ourinstall. Now to begin our installation, we'll need to drop our exhaust tailpipe down. To do thiswe'll spray some lubricant on the rubber isolator and then remove it using a pry bar.This will allow us to move the tailpipe around in order to secure our fasteners.
Trailer Hitch Installation - 2008 Toyota FJ Cruiser - Curt
Today on our 2008 Toyota FJ Cruiser we'll be installing Curt Hitch, part number13367. Now to begin our installation, we'll need to drop our exhaust tailpipe down. Todo this we'll spray some lubricant on the rubber isolator and then remove it using apry bar. This will allow us to move the tailpipe around in order to secure ourfasteners. Here on the driver's side we'll need to remove the tow loop. With the towhook removed, we'll go ahead and point out our attachment points.
Glacier Square-Link Snow Tire Chains Review - 2008 Toyota FJ Cruiser
Today on our 2008 Toyota FJ Cruiser with a 265 75R16 tire we'll be installing PewagGlacier Chains, part number PWH2328SLC. This is a set of two square length snowtire chains with cam tighteners for light trucks. These will fit front or rear wheel drivevehicles. To install them on the vehicle, we'll lay the chain out first and ensure that allthe kinks and twists are out of the chains. We'll also need to make sure that the camson the chain face towards the outside of the tire. You'll notice that the cross chains arehooked to the main chain.
Husky Rear Floor Liner Review - 2012 Toyota FJ Cruiser
Today in our 2012 Toyota FJ Cruiser, well be test fitting the Husky Floor Liner in the second row part number HL65961. First well go ahead and remove the old or the manufacturers floor mats, now were ready to install the Husky Floor Liner. Husky Liners are custom-molded to precisely fit the vehicle and stay in place. The shape, channels and moldings all work to keep dirt and debris contained in the liner and off of the carpeting. As you can see, this is a one-piece liner and extends all the way from the driver side to the passenger side. The one-piece liner goes up over the center hump and has a raised back edge and fits around the second row seat mounts also.
Husky Front Floor Liners Review - 2012 Toyota FJ Cruiser
Today in our 2012 Toyota FJ Cruiser, well be installing the Husky Floor Liner in the front row part number HL35931 black in color. First well go ahead and remove the old or the manufacturers floor mat, now were ready to install the Husky Floor Liner. Husky Liners are custom-molded to precisely fit the vehicle and stay in place. The shape, channels and moldings all work to keep dirt and debris contained in the liner and off of the carpeting. Special moldings and cutouts will go around the manufacturers attachment points and has the extended front edge that is molded around the floor board and can go up underneath the gas and brake pedal. As you can see, these liners provide maximum coverage.
Husky Cargo Floor Liner Review - 2012 Toyota FJ Cruiser
Today on our 2012 Toyota FJ Cruiser, well be test fitting the Husky Floor Liner part number HL25951 black in color. First well go ahead and remove the old or manufacturers floor mat. Now were ready to install the Husky Floor Liner. Husky Liners are custom-molded to precisely fit the vehicle and stay in place. The shape, channels and moldings all work to keep dirt and debris contained in the liner and off of the carpeting. As you can see, its got a raised lip along the outer edge that will really help contain dirt, dust, debris and any fluids you may get on the liner.
Trailer Hitch Installation - 2012 Toyota FJ Cruiser - Hidden Hitch
Today on our 2012 Toyota FJ Cruiser, well be installing the Hidden Hitch part number 87412. This is what our hitch will look like once its installed in the vehicle. Next, well go ahead and give you a couple of measurements to assist you in selecting accessories for you new hitch. From the center of the hitch pinhole to the outermost edge of the spare tire cover is 8 inches, from the top of the receiver tube to the ground it 19 inches. This will assist you with selecting accessories such as a drawbar, a bike rake or a cargo carrier. Now lets go ahead with the installation.
Trailer Hitch Installation - 2012 Toyota FJ Cruiser - Draw-Tite
Today on our 2012 Toyota FJ Cruiser, well be installing the Draw-Tite Hitch part number 75461. This is what our hitch will look like once its installed in the vehicle. Next, well go ahead and give you a couple of measurements to assist you in selecting accessories for you new hitch. From the center of the hitch pinhole to the outermost edge of the spare tire cover is 8 inches, from the top of the receiver tube to the ground it 19 inches. This will assist you with selecting accessories such as a drawbar, a bike rake or a cargo carrier. Now lets go ahead with the installation.
Trailer Hitch Installation - 2012 Toyota FJ Cruiser - Curt
Today in our 2012 Toyota FJ Cruiser, well be installing the Curt Hitch part number 13367. This is what the hitch will look like once its installed in the vehicle; next well go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the spare tire cover is 6 inches, from the top of the receiver tube to the ground it 19 inches. This will assist you with selecting accessories such as a drawbar, a bike rake or a cargo carrier. Now lets go ahead with the installation. Before we can begin installing the hitch, first well go ahead and remove the tow hook here on the driver side frame rail.
Putco PURE LED Dome-Light Kit Manufacturer Installation - Toyota FJ Cruiser
Gently remove the dome light cover with a screw driver, making sure not to force it out. With the cover off, remove the bulb by pushing on the metal tab holding it in. Now, replace that bulb with your new Putco LED light by placing the brackets in place of your old factory bulb. Snap the dome light cover back into place. And congratulations, you have just installed your new Putco LED dome light.
Trailer Brake Controller Installation - 2008 Toyota FJ Cruiser Part 2
All right next what we need to do is run this wire up to the front side of the vehicle up by our fire wall. Basically we just have to keep this as close to the frame as possible away from the exhaust and also as far to the left as possible to keep it away from the steering arm too. We have got our wire pulled through on the top here but we need to get to the left side as far as possible so push it back down and pull it on this side so it will come back close to our battery and our access point through the fire wall right here. And you will notice we ran the wire from here all the way up to the positive terminal here. :35
Trailer Brake Controller Installation - 2008 Toyota FJ Cruiser Part 1
Today we are going to do an install of a brake controller on a 2008 Toyota FJ Cruiser. We are going to be using part number ETBC7 and we are also going to install the Prodigy brake controller part number 90185. The first step we are going to do is mount up our bracket. What that is going to involve is we are going to take this panel loose and we are going to take this 4-pole mount off because our parts are going to replace this area. :22
Westin Bull Bar Installation 2008 Toyota FJ Cruiser
Today we are going to install part number 32-2210 from Westin. It is the Bull bar assembly we will be installing on a 2008 Toyota FJ Cruiser. To start our install we will have to install some brackets onto the frame itself and they are tucked up pretty far up in here on the brace that holds the bumper up. There are 2 existing holes so what you need to do is drop 2 bolts into the bumper bracket from the top all the way down through the bottom and it comes with these long bolts to do it with. Now to install one of 2 brackets. There is going to be one here and one is going to have an out rigger from here going out to this bracket to the assembly right here. We do not want to tighten them up yet, we just want to leave them snug so that we have some working room. Next this bracket has to get installed behind it. Then it gets bolted to this assembly here. And then this bracket gets bolted to a threaded hole that is already inside the assembly here.
Front Mount Trailer Hitch Installation - 2008 Toyota FJ Cruiser
Today we are going to install part number 31367 from Curt. We are going to install a front mounted hitch on a 2008 Toyota FJ Cruiser. To do our install the hitch mounts in 3 different places. One is right here where we are going to take this bolt out here. There are three nuts over here on the right side where we take out the lowest one on this side. The hitch also attaches to the tow loop here and they will be the same on both sides. Go ahead and break these loose. It would be a good idea to have one of these ratcheting wrenches, this makes life real easy on this install. Next we can install our hitch. One thing you have to do obviously get the arms up in here to match that, but also the tabs on the hitch have to fit over the tow hooks. It is a tight fit, you just have to wiggle it into place. At this point we can go ahead and re-install our hardware.
Toyota FJ Cruiser Questions and Answers
- Are Two Lights Included with Off-Road Light Kit # MH-400D and are the Lenses Clear
- The Off-Road Light Kit, # MH-400D, includes 2 lights. The lenses are best described halogen headlights like what used to be on cars. I would say it is translucent, not completely clear.
view full answer...
- 6-Pole Extension Recommendation for 2008 Toyota FJ Cruiser and 2005 Hunter Fat Shadow Trailer
- We do have a solution for you, but the Hopkins Heavy-Duty Trailer Coiled Extension # HM47055 you referenced has female connectors on both ends and is 8 feet in length.
If you have a 6-way male connector on your FJ, my recommendation is to replace the connector with the appropriate length of Deka Wire # DW04906-1 and use a Pollak 6-Pole Connector # PK11604. By using this, you will not need an extension.
I have provided a link to a video showing how to replace a 6-pole connector.
view full answer...
- Will a Thule Apex Swing 4 Bike Rack Clear the Spare Tire of a 2012 FJ Cruiser
- On similar 2012 Toyota FJ Cruisers we have found that the distance from the center of the hitch-pin to the outer most edge of the spare tire is 8 inches. The Thule Apex Swing 4 Bike Carrier # TH9027 has a distance of 10-1/2 inches from the center of the hitch pin hole to the back of arms of the rack so it should have plenty of clearance and work very well for you.
I attached a review video for this product for you to check out also.
If you plan on carrying any womens or alternative framed
view full answer...
- Swagman Titan Bike Rack Recommendation for a 2012 FJ Cruiser
- The Swagman Titan 3 bike rack # S63405 is an excellent choice for a bike rack that has many of the features as some of the more expensive racks. For the money I think it is one of the best racks we offer and I believe it would work very well for you.
I already checked and you should have plenty of hitch-to-bumper clearance for this rack to fit on your vehicle as well.
I attached a review video for you to check out also.
If you plan on carrying any womens or alternative framed bikes that
view full answer...
- Which Class III Trailer Hitch Receiver for 2008 Toyota FJ Cruiser
- We offer three different trailer hitch receivers for your 2008 Toyota FJ Cruiser (so long as it does not have the auxiliary fuel tank option), the Hidden Hitch # 87412, the DrawTite # 75461 and the Curt # 13367. All three offer the same 2-inch receiver opening, 500-lb tongue weight rating and 5000-lb tow rating. All three install without drilling or welding required. I have included a link to the hitch page for your FJ Cruiser where you can see all three products. Installation videos for all thr
view full answer...
- Universal Towing Mirror Recommendations for a 2007 Toyota FJ Cruiser
- For mirrors that are much taller than normal mirrors like those on your 2007 Toyota FJ Cruiser, I recommend going with a suction cup mount like # CM11954 or, for more security, a door mount mirror, # 11650. The door mount is going to give you the best performance and vision. I have linked a video showing a typical installation for you.
view full answer...
- Which is Better, a Side Wind Trailer Jack or a Top Wind Trailer Jack
- You would choose a side wind or top wind jack based on several factors. Each has its advantages. If clearance is an issue for the radius of a top wind, then you would choose a side wind. The opposite is also true. It is my experience that a side winding jack is easier to turn. However, if the tongue is low to the ground a top wind would be a better option because you would not have to bend down as much and it would not be as awkward to turn.
A side winding jack normally has inner components t
view full answer...
- Front Mount Trailer Hitch Receiver for a 2012 Toyota FJ Cruiser
- We carry a front mount trailer hitch with a 2 inch receiver that will fit your 2012 Toyota FJ Cruiser. You can use Curt front mount receiver # 31367. I have included links to the instructions and a link to a video showing a typical installation for you.
When used with a winch the hitch is rated for a line pull up to 9,000 pounds, gross trailer weight up to 3,500 pounds, and vertical load up to 350 pounds.
view full answer...
- Installing Additional 12-Volt Accessory Power Circuit to Trailer
- I do not have a schematic available, but I would be happy to run you through the process.
You certainly can run a separate circuit for a trailer mounted battery. You would want to make a separate wiring run from the vehicle battery, using 10 gauge wire and another # 9510 40 amp breaker. You would attach that circuit to the purple wire of the # 37185. You would then have the wire feeding the center pin on the 7-way plug on the trailer connect to the positive trailer battery terminal, with the
view full answer...
- Will Yakima SwingDaddy Trailer Hitch Mount Bike Rack Clear the Spare Tire on 2008 Toyota FJ Cruiser
- To determine if the Yakima SwingDaddy, # Y02422, or any hitch mount rack will clear the spare tire on your 2008 Toyota FJ Cruiser, you will need to take one important measurement. Measure from the center of the hitch pin hole straight back to the distance required to clear the spare tire on the vehicle.
If the measurement is less than 11 inches then the rack will fit but you will also need a measurement less than 6 inches from the hitch pin hole to the back of the bumper for the lower part of
view full answer...
- Installation of Air Lift 1000 Helper Springs # AL60809 on 2012 Toyota FJ Cruiser
- To install the Air Lift 1000 Helper Springs, part # AL60809 on your 2012 Toyota FJ Cruiser, it does require you to remove the coil springs on the rear of your vehicle
To remove the coil springs on your FJ Cruiser you will raise the rear of the vehicle and support the frame with jack stands. Detach the shock absorbers at the lower shock mount. Detach the panhard rod at the lower axle mount. If your vehicle has rear anti-sway bar you may have to disconnect the links.
Then, mark the position
view full answer...
- Rubber Cargo Mat Recommendations for a Toyota 2008 FJ Cruiser
- The Highland Floor Mats # 46026 that you referenced are very much a heavy rubber floor mat that is confirmed to fit your 2008 Toyota FJ Cruiser. These mats also feature deep, sculpted ridges that will also provide your feet with good traction.
For a matching set for the second row you would want Highland Floor Mats # 46031. These are a universal set that has been confirmed to work in the second row of your vehicle and are made of the same rubber.
For the cargo area you would want a Highlan
view full answer...
- Selecting Carr Gutterless Light Bars for 2009 Toyota FJ Cruiser
- There are two general types of light bars to consider, fixed and rotating. Rotating bars allow the bar and attached lights to rotate down out of the way when not in use. Both types can accept up to 4 lights.
Since the vehicle is predominantly black in color, and has black roof rails, I will suggest you consider options with black powder-coat finish as these may offer the best cosmetic match.
For the fixed-type bar, I suggest the Carr M-Profile Light Bar - Black Powder Coated Steel
Gutterl
view full answer...
- Will the Yakima SkyBox 21 Cargo Box Fit on a 2010 Toyota FJ Cruiser With Factory Roof Rack
- We do have a solution for you, however, Yakima states that the SkyBox 21 Cargo Box, # Y07184, will not fit directly on the factory roof rack of your 2010 Toyota FJ Cruiser.
First, you will want to install the Yakima RailGrab Roof Rack, # Y00409 and # Y00138. This will provide crossbars that the SkyBox 21 cargo box will mount to. I have attached the installation instructions as well as an installation video of this roof rack for you to check out. You will notice that the vehicle in the video
view full answer...
- Tekonsha Prodigy RF Only Flashes NC on Trailer and 2011 Toyota FJ Cruiser
- You have identified the problem. The Tekonsha Prodigy RF, # 90250, requires the 12 volt circuit on the 7-Way to provide power to the unit. You will need to connect that black wire to the positive battery terminal via a 40 amp circuit breaker, # PK54540. It has to be the battery, no other source is tested or rated for the power draw.
If the 7-Way did not come with wire to run to the battery you can use about 20 feet or so of # 10-1-1 (sold in 1 foot increments). Route the wire from the 7-Way,
view full answer...
- Quality and Material of the Putco Chrome Fuel-Tank Door Cover for a 2012 Toyota FJ Cruiser
- The Putco Chrome Fuel-Tank Door Cover, # P400937, is made of automotive grade ABS plastic and is then chrome plated. This cover is durable and will withstand normal environmental and driving conditions. Like any chrome accessory, it can be chipped if struck the right way but cracking and peeling should not be an issue. I have included a link to the installation details for you.
view full answer...
- Will the K Source Universal Clip-On Towing Mirror Fit a 2007 Toyota FJ Cruiser
- The K Source towing mirror # KS3891 is a universal fit item that is made to clip around a mirror housing that has a gap or lip between the glass and mirror housing. IF you can get the straps tight enough they will fit well though there may be some vibration. We have several other universal towing mirrors available. I have included a link to them for you to view.
view full answer...
- Timbren Suspension Enhancement for a 2011 Toyota FJ-Cruiser Trail Edition
- Adding suspension enhancement like Timbrens will help with sag and increase stability and ride quality. If your 2011 Toyota FJ Cruiser is a 4-wheel drive model, for the front you can use # TTOFTAC4A that you have referenced. There is no option for the front if it is a 2-wheel drive model.
For the rear if it is 2- or 4-wheel drive use # TTORSEQ. I have included links to the instructions for both sets for you to view. I have also included a link to our FAQ article on Timbren suspension enhancem
view full answer...
- Installation of Prodigy RF Brake Controller # 90250 on 2012 Toyota FJ Cruiser
- To power the Prodigy RF Brake Controller, part # 90250, it is only necessary to connect the 12 volt power wire (black) and ground wire (white) on your 4-Way to 7-Way Adapter, part # 37185, in the # ETBC7 kit, on your 2012 Toyota FJ Cruiser. The remaining wires can be tied off.
You also have the option to connect the auxiliary wire (purple) if you need to power backup lights or another accessory on your trailer.
To prepare the adapter to hook up the brake controller, you will attach the gr
view full answer...
- Will the Thule Vertex Swinging Trailer Hitch Mount Bike Rack Fit a 2012 Toyota FJ Cruiser
- We have installed the Hidden Hitch Class III trailer hitch # 87412 on a 2012 Toyota FJ Cruiser, see video link, and found that the distance needed to clear the rear part of the spare tire carrier is 8 inches. Measure from the center of the hitch pin hole straight back to the distance required to clear the spare on your vehicle to confirm.
The Thule Vertex swinging rack, # TH9031, measures 14 inches from hitch pin hole to the back of the upright arm so it should clear the spare tire on your FJ
view full answer...
- Will a 2007 Toyota FJ Cruiser Need a Brake Controller to Tow a 2001 Casita Trailer
- Before you decide if you want a brake controller or not you should check with your local laws and regulations to determine what towing setups are required to have trailer brakes activated by a brake controller. Some states require trailer brakes and a brake controller on any vehicle that is towing a trailer.
Also, it may seem like the trailer will be lightweight enough for you to stop reasonably, but in an emergency situation where you need to stop abruptly that 2,500 lb trailer will make it
view full answer...
- Transmission and Engine Oil Cooler Recommendations for a 2009 Toyota FJ Cruiser
- If you are not a fan of the tube-fin design then I would go with separate coolers using a plate-fin design. For a transmission cooler, the most popular one for a 2009 Toyota FJ Cruiser is Derale cooler # D13503. I have included a link to all of the recommended plate-fin coolers for your vehicle.
For an engine oil cooler, a stacked plate design, like # D15651, will take up the least space. This cooler has 3/4-16 filter threads and 2-3/4 inch o-ring which is what should be on your FJ.
I have
view full answer...
- Will Yakima SpareTime 2 Bike Carrier # Y02598 Fit the Spare Tire on a 2007 Toyota FJ Cruiser
- To determine if the Yakima SpareTime 2 Bike Carrier, # Y02598, will fit your 2007 Toyota FJ Crusier, there are a couple of important measurements that you will need to take.
Measure the diameter of the hole in the center of your spare tire wheel. It will need to be greater than 1-3/16 inches. Then, measure the distance from the back of the wheel, where the mounting plate will bolt up to the wheel, to the farthest out part of the spare tire. This measurement will need to be less than 6-1/2 inc
view full answer...
- Weight Distribution Recommendation for a 2012 Toyota FJ Cruiser and 2,900 Pound Trailer
- Anytime the trailer weight is at least 50 percent of the vehicle weight OR if the vehicle sags at the back with the trailer connected, you would benefit from a weight distribution system. To determine the correct system for your application you will need to know the total tongue weight.
The total tongue weight can be calculated by taking the tongue weight of the trailer, loaded and ready to tow, then add to that the weight of anything loaded behind the rear axle of the tow vehicle. I have inc
view full answer...
- Do Mounting Plates of Stromberg Carlson or Ultra-Fab Scissor Jacks Remain Level When Jack is Raised
- As the jacks are raised an lowered, the upper mounting plate are designed to remain level.
As you can see from the photo I edited, the ends of the jack uprights have gears or teeth built into them so that the mounting plate remains level. The Stromberg Carlson Jack, part # JSC-24-IND operates the same way.
view full answer...
- Recommendations to Carry 2 or 3 Bikes on a 2012 Toyota FJ Cruiser with Spare Tire Camera
- You have two options that will allow you to carry 2 or 3 bikes on your 2012 Toyota FJ Cruiser with the spare tire camera. You could use hitch mounted bike racks or roof mounted bike racks. The spare tire camera will prevent you from using a spare tire mounted bike rack.
The first option that I would recommend would be a hitch mounted bike rack. This will require you to have a trailer hitch on your vehicle. If you do not have a trailer hitch on your vehicle and are interested in adding one,
view full answer...
- Will the Thule Atlantis 1600 XT Cargo Box Fit on a 2011 Toyota FJ Cruiser with Factory Roof Rack
- The Thule Atlantis 1600 XT Cargo Box, # TH686XT, is confirmed, by Thule, to fit the factory roof rack on your 2011 Toyota FJ Cruiser. This cargo box has 16 cubic feet of space and measures 74 inches long x 36 inches wide x 16-5/16 inches tall. This cargo box is also available in black with part # TH686BXT.
You may also be interested in a tire step like the HitchMate TireStep, # HE4040. I recently used this step to install a cargo box on a large SUV and it saved a lot of time and hassle for th
view full answer...
- Can Thule Stay-Put Cradles be Fitted with Anti-Sway Cages
- The Thule Stay-Put cradle, # 853-7887, can be fitted with an anti-sway cage using # 853-7758. For the cradle and for the cage you would use strap # 853-5834.
view full answer...
- Yakima SwingDaddy Recommendation for a 2012 FJ Cruiser for Complete Rear Door Access
- I believe the perfect rack for you would be the Yakima SwingDaddy 4 Bike Carrier # Y02422. This will swing out to give you complete access to the rear of your vehicle, even if you have bikes on the rack. The arms of this rack can also fold down when you are not carrying any bikes to allow you to have better clearance at the rear of your vehicle.
Check out the review video and installation instructions I attached for you to check out.
If you plan on carrying any womens or alternative framed
view full answer...
- Yakima SwingDaddy 4 Bike Rack Recommendation for a 2012 Toyota FJ Cruiser
- I believe I have a swing away 4 bike rack that will work on your 2012 Toyota FJ Cruiser, but the Thule Apex Swing 4 Bike Carrier # TH9027 that you referenced will not have enough clearance to clear your spare tire. We have an FJ Cruiser in our parking lot that has a distance of 8-1/2 inches from the center of the hitch pin out to the furthest part of the spare tire. Since the # TH9027 has a distance of 7-1/2 inches from the center of the hitch pin to the nearest portion of the rack it would not
view full answer...
all Toyota FJ Cruiser questions
