Trailer Hitch Installation - 2012 Toyota Camry - Curt
Today, on our 2012 Toyota Camry Hybrid, we'll be installing the CURT hitch, part number C12082. This is what our hitch will look like once its installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is two and a half inches. From the top of the receiver tube opening to the ground is eleven and a quarter inches.This will assist you selecting accessories such as a ball mount, a bike rack, or a cargo carrier. To begin our install, we'll first need to remove the under body trim panel and its multiple fasteners that secure it.
Trailer Hitch Installation - 2005 Toyota Camry - Curt
Today on this 2005 Toyota Camry were going to install part number C12339 from Curt. This is what the hitch looks like once installed on the vehicle. Next, well give you some measurements to help you out in selecting some accessories such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 11-1/2 inches. From the center of the hitch pinhole to the edge of the bumper will be about 2-3/8 inches. Now well go ahead and show you how the hitch is installed.
Rain-X Fusion Wiper Blades Installation - 2005 Toyota Camry
Today on this 2005 Toyota Camry were going to do a test fit the Rain-X Windshield Wiper Blades. Well be working with part number RX880008. This is their Fusion Windshield Wiper Blade. A few things to know about this is that its designed in all weather wiper blade thats designed for rain, snow and sleet. It has a durable casing on the frame to help prevent ice and snow from building up on it. It has a synthetic rubber squeegee with built in UV inhibitors to help protect it from the sunlight.
Rain-X Weatherbeater Wiper Blades Installation - 2005 Toyota Camry
Today on this 2005 Toyota Camry were going to do a test fit of part number RX30224 from Rain-X. This is our Weatherbeater Windshield Wiper Blade. A few things to know that this is designed to be an OEM replacement windshield wiper blade. It has a frame style design that has multiple pressure points along the blade to help keep it against the windshield, and a rubber squeegee. It has UV inhibitors to help protect it from the sunlight. To start our test fit well go ahead and remove the original wiper blade.
Thule Traverse Roof Rack Installation - 2008 Toyota Camry
Today on our 2008 Toyota Camry well be installing the Thule Traverse Roof Rack System using part numbers THLB50, TH480 and THKIT1438. Now weve already gone ahead and preassembled our roof rack system according to the instructions found within the fit kit so were ready to fit it to the vehicle. Well start by placing our front crossbar on top of the roof, well then measure from the windshield edge back on our roof 9 inches. This will be the location of the leading edge of the front crossbar feet. With our crossbar in place well open the door as the clamp will clamp to the inside of the door opening. We can then tighten down the two feet for the front crossbar using the included torque tool found within each foot.
Thule Echelon Roof Bike Rack Review - 2008 Toyota Camry
Today, on our 2008 Toyota Camry, we'll be test-fitting the Thule Eschelon roof-mounted bike carrier, part number TH518. Now, our Camry's already equipped with the Thule traverse roof rack system, so were ready to load our Eschelon. We'll begin by placing the bike rack on top of our crossbars in a location suitable for us. We'll make sure that the head of the bike rack is directly over the front cross bar where we can then take the rear mount of the Eschelon and make sure if it's over the rear crossbar. We'll then simply run the clamp underneath the crossbar and loosely fasten the wing nut to the bolt. We'll then move forward to the head of the bike rack.
SportRack Nomad Roof Bike Rack Review - 2008 Toyota Camry
Today, on our 2008 Toyota Camry, we'll be installing the SportRack Nomad framed mount bike carrier, part number ABR611. Now, to begin our test-fit, we'll simply place our bike rack on top of our cross bars. We'll make sure that the head of the bike rack is directly over our front cross bar where we can now take our back cross bar and ensure that it's over the rear cross bar. To move it, you'll simply remove the bolts and use any of the pre-existing holes drilled in the bike rack to adjust the rear mount. We'll then go ahead and loosely install out rear mount over the rear crossbar. We'll move back to the front where we use the 2 U bolts and wing nuts to secure the head of the bike rack to the front crossbar.
Rain-X Fusion Wiper Blades Installation - 2012 Toyota Camry
Today on this 2012 Toyota Camry, we're going to do a test fit of part number RX880008 from Rain-X. This is their Fusion Windshield Wiper Blade. A few things to know about this windshield wiper blade, it's designed to be an all-weather windshield wiper blade. It has a durable casing on it to help prevent ice and snow from building up on the pressure points. Now, the squeegee also has UV inhibitors to help protect it from the sunlight. Now, we'll start off our test fit by removing the original ones with a small tab we have to lift up to release them.
Trailer Hitch Installation - 2012 Toyota Camry - Draw-Tite
Today on this 2012 Toyota Camry were going to install part number 36514 from Draw Tite. This is what the hitch looks like when its installed on the car. Next well give you some measurements to help you out in selecting some accessories such as a bike rack or a cargo carrier. From the top of the receiver opening down to the ground will be 11 inches, and from the center of the hitch pin hole to the edge of the bumper will be about two inches. Now well go ahead and show you how the hitch is installed. First we have to look at the vehicle on the drivers side frame rail.
Trailer Hitch Installation - 2008 Toyota Camry - Hidden Hitch
Today on this 2008 Toyota Camry were going to install part number 90152 from Hidden Hitch. This is what the hitch looks like when its installed on a vehicle. Next well give you some measurements thatll help you with selecting some accessories such as the bike rack or a cargo carrier. From top of the receiver opening down to the ground will be about 11 inches. From the center of the hitch pin hole to the edge of the bumper will be about 4 inches. Now Ill go ahead and show you how the hitch is installed.
Trailer Hitch Installation - 2008 Toyota Camry - Draw-Tite
Today on this 2008 Toyota Camry, we're going to install part number 36416 from Draw-Tight. This is what the hitch looks like when it's installed on a vehicle. Next, we'll give you some measurements to help you out in selecting some accessories such as a bike rack, or a cargo carrier. From top of receiver opening down to the ground, will be about 11 inches. From the center of the hitch pinhole to the edge of the bumper, will be about 4-1/2 inches. Now, we'll go ahead and show you how the hitch is installed.
Yakima DoubleDown Ace Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry well be test fitting part number Y02451. This is the Yakima DoubleDown 4 Bike Carrier. Now to begin our test fit, well slide the bike rack shank into the hitch after removing the 2-inch adaptor. Well then install the attached hitch pin where we can then move to the back of the shank and tighten the knob securing our bike rack to the vehicle. Well now pull the handle here at the bottom of the bike rack mast to allow the mast to tilt down. We can then open our deck lid.
Trailer Hitch Installation - 2007 Toyota Camry - Hidden Hitch
Today on this 2007 Toyota Camry were going to install part number 90152 from Hidden Hitch. This is what the hitch looks like when its installed on the car. Next, well give you some measurements to help you out in selecting some accessories, such as a ball mount, bicycle rack or a cargo carrier. From top of receiver opening down to the ground will be 11 inches and from the center of the hitch pin hole to the edge of the bumper will be five inches. Now, well go ahead and show you how the hitch is installed. First thing you need to do, is get inside the trunk and remove the spare tire.
Thule Vertex 4 Hitch Bike Rack Review - 2007 Toyota Camry
Today, on our 2007 Toyota Camry, we'll be test fitting the Thule Vertex 4 bike carrier for both inch and a quart and 2 inch hitches, part number th9029.We're going to begin our test fit. We'll remove the 2 inch adapter. We can then slide in the bike rack shank to the hitch, line up the hitch pin hole and install and tighten down on our anti-rattle bolt. With our bolt tight, our bike rack can secure to the vehicle.Now, we'll go ahead and give you a few measurements. Now, the ground clearance at our bike rack is 9 1/2 inches, and from the closest point of the bike rack to the back of the vehicle is 3 inches. We'll now go ahead and pull the hitch switch at the bottom of the bike rack mast to allow the mast to tilt down.
Thule Hitching Post Pro Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry well be test fitting the Thule Hitching Post Pro, part number TH934XTR. To begin our test fit, well slide our bike rack shank into the hitch after removing the two inch adapter from our shank. We can then line up the hitch pin hole where well install and tighten down our anti-rattle bolt. With our bolt tight, our bike rack is secured to the vehicle. Now well give you a few measurements. Our ground clearance at the bike rack is 8 inches and from a closest point of the bike rack to the back of the vehicle is 6 inches.
Thule Apex 4 Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry we'll be fitting the Thule Apex 4-bike carrier, partnumber TH9025. Now we've already gone ahead and removed the 2" adapter from our bike rack shank,so we'll go ahead and slide the bike rack shank into the hitch. We'll make sure to pullthe integrated locking hitch pin and allow it to move over our hitch. We'll then allowit to fall into the hitch pin hole where we can move to the back of the shank andtighten the knob down, securing our bike rack to the vehicle. We'll now go ahead and give you a few measurements. Now, our ground clearance atthe bike rack is 9-1/2", and from the closest point of the bike rack to the back of thevehicle is 2-1/2".
Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry we'll be test fitting part number S64670, theSwagman XTC2 2-bike carrier for both 1-1/4" and 2" hitches. Now to begin our installation we'll remove the 2" adapter from the shank of the bikerack. We can then slide the bike rack shank into the hitch, line up the hitch pin holeand install and tighten down our anti-rattle bolt. With our bolt tight, our bike rack issecured to the vehicle. We'll now go ahead and unfold the bike rack platform andopen the trunk. And as you can see, we can gain access to the cargo area, opening thedeck lid completely, with this bike rack.
SportRack EZ Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry we'll be testing the SportRack 2-bike Hitch-mounted Bike Rack for both 1-1/4" and 2" hitches, part number A30901. Now to begin our test fit we've already gone ahead and removed the 2" adapter, sowe'll slide the bike rack shank into the hitch, line up the hitch pin hole, and install andtighten down our anti-rattle bolt. With the bolt tight. our bike rack is secured to thevehicle. Now we'll go ahead and give you a few measurements. Our ground clearanceat the bike rack is 14-1/2", and from the closest point of the bike rack to the back ofthe vehicle is 6-1/2".
Pro Series Q-Slot Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry we'll be test fitting the Pro Series Q-slot Platform-style 2-bike Carrier for 1-1/4' and 2" hitches, part number PS63134. Now to begin our test fit we'll slide our bike rack shank into the hitch. After removingthe 2" adapter, we can then line up the hitch pin hole and install our hitch pin. We'llthen put the safety clip on the other side of the pin, which will secure our bike rack tothe vehicle. We'll now go ahead and give you a few measurements. Our groundclearance at the bike rack is 13-1/2", and from the closest point of the bike rack to theback of the vehicle is 6-1/2".
Kuat Alpha Hitch Bike Rack Review - 2007 Toyota Camry
Today on our 2007 Toyota Camry we'll be testing the Kuat Alpha Folding, Locking 3-bike Aluminum Rack for 1-1/4" hitches, part number A103-WHITE-114. Now to begin our test fit we'll simply slide the bike rack shank into the hitch, line upthe hitch pin hole and install our hitch pin. We can then move to the back of the shankwhere we'll tighten down the knob, securing our bike rack to the vehicle. We'll nowgo ahead and give you a few measurements. Our ground clearance at the bike rack is9-1/2", and from the closest point of the bike rack to the back of the vehicle is 5-1/2".We'll now go ahead and pull the pin here at the bottom of the mast to allow the mastto tilt down, where we can then open our trunk. And as you can see, we can gainaccess to the cargo area, opening the trunk completely, with this bike rack.
Trailer Hitch Installation - 2011 Toyota Camry - Hidden Hitch
Today on our 2011 Toyota Camry, we'll be installing Hidden Hitch, part number 90152. Now before we begin our installation, here are a few measurements to help you in selecting accessories such as a cargo carrier or a bike rack. From the center of the hitch pin hole to the outermost part of the bumper is 4-1/2 inches and from the top of the receiver tube to the ground is 10-1/4 inches. Now, we'll go ahead with our install. Now to begin our installation, we'll go ahead and remove the spare tire and all the components from the inside the trunk. We'll next need to lower the vehicle exhaust.
Thule Helium Hitch Bike Rack Review - 2011 Toyota Camry
Today, on our 2011 Toyota Camry, we are going to test fit part number TH970XT from Thule. This is a Helium bicycle rack. A few notes about this rack is that it will work with 1-1/4 inch receiver hitches, both class 1 and class 2. This will also work with 2 inch receiver hitches with the included spacer. Today, we will be working with a 2 inch receiver hitch. Now, I will start off our test fit by installing the bike rack into the hitch.
Swagman Titan Hitch Bike Rack Review - 2011 Toyota Camry
Today, on our 2011 Toyota Camry, we are going to do a test fit of part number S63410 from Swagman. This is a Titan 4 bike rack. A few things to note about this bike rack, that it will work with 1-1/4 receiver hitches, both class 1 and class 2. However, if you are using it for the class 1 hitch, you are limited to carrying just 2 bikes. Now, this will also work with a 2 inch receiver hitch with provided spacer. We will begin our test fit by installing the bike rack into the hitch.
Thule Hitching Post Pro Hitch Bike Rack Review - 2011 Toyota Camry
All right, today on this 2011 Toyota Camry, were going to do a test fit of part number TH934XTR from Thule; this is the Hitching Post Pro. A few notes about this bicycle rack is that it will work with 1- inch receiver hitches, both class 1 and class 2; however, when you use this for a class 1 receiver hitch, youre limited to carrying just two bicycles. Now this will also work with 2-inch receiver hitch with the included spacer. Today well be working with a class 2 receiver hitch. Now, well start off our test fit by installing the bike rack into the hitch, then well tighten down the anti-rattle bolt. After that, we can go ahead and give you a couple of clearance measurements.
Thule Doubletrack Hitch Bike Rack Review - 2011 Toyota Camry
Today on this 2011 Toyota Camry, were going to do a test fit of part number TH990XT from Thule, the DoubleTrack Platform Style bike rack. A few things to know about this bike rack is that it will work with 1- inch receiver hitches, both class 1 and class 2. This will also work with a 2-inch receiver hitch with the included adapter. Well start off our test fit by installing the bike rack into the hitch. Then, well go ahead and tighten down the anti-rattle bolt and install the lock on the other side. After that, well go ahead and get a couple of clearance measurements.
Kuat Alpha Hitch Bike Rack Review - 2011 Toyota Camry
All right, today on this 2011 Toyota Camry, were going to do a test fit of part number A103-WHITE-114 from Kuat; this is our Alpha Bicycle Rack. A couple of things to know about this bike rack is that it will work with 1- inch receiver hitches, only both class 1 and class 2. Now well start off our test fit by installing the bike rack into the hitch, then well install our pin and lock. Then well go ahead and tighten down the anti-rattle knob and then we can go ahead and get some clearance measurements. The clearance from the bike rack to the bumper is going to be 5 inches. Ground clearance with the anti-rattle knob in the horizontal position is going to be 10 inches.
Trailer Wiring Harness Installation - 2004 Toyota Camry
Today on our 2004 Toyota Camry well be installing Tow Ready T-One Connector, part number 118308. After opening thetrunk were ready to begin our install. Well need to remove the trunk threshold from the vehicle. Well remove the 2 hookshere on the upper side of the threshold. Well now use our pry tool to work underneath the threshold from the molding andpry up. Now that weve removed the threshold well go ahead and remove the tail light covers here.
Trailer Hitch Installation - 2004 Toyota Camry
Today on our 2004 Toyota Camry, well be installing Draw-Tite Hitch part number 24715. Before we start our installation, here are a few measurements. This will help you when selecting accessories such as a cargo carrier or a bike rack. From the top of the receiver tube to the ground is 11 inches and from the center of the hitch pinhole to the outermost part of the bumper is 3 inches.Now well go ahead with our install. To begin our installation, well need to remove the rear exhaust hanger on the passengers side as this will be the two attachment points for our hitch. On the drivers side, well need to locate our attachment points, which are two weld nuts.
Yakima Q Tower Roof Rack Installation - 2012 Toyota Camry
Today we have a 2012 Toyota Camry and we are going to test fitting a Yakima roof rack system. We are going to be using Q clips part number y00605 as we as Q clips part number y00716. Well also be using the 48 inch crossbars part number y00408 and the Yakima roof tower part number y00124. We already have our roof rack assembled according to the instructions and now we are ready to fit it up on top of our vehicle. Well take the front crossbar and lay it on top of the roof. To position the front bar we need to measure eight inches from the edge of the windshield to the leading edge of the Q towers.
Thule Flat Top Ski and Snowboard Carrier Review - 2012 Toyota Camry
Today we have a 2012 Toyota Camry and we'll be testing the Thule Flat Top Ski and Snowboard Carrier, part number TH92725. To fit the carrier to our roof rack all we need to do is take the first half, set it on top of our front load bar and wrap the Speed-Link straps around the bar. We'll use the hand knobs to tighten down the straps. Once we have the front half on, we can move to the rear bar and repeat the same procedure. With that, our ski carrier is secured to our roof rack and we're ready to load up. We'll push the gray buttons on the end to open the jaws of the carrier.
Yakima QuickBack 2 Bike Rack Review - 2012 Toyota Camry
Today, we have a 2012 Toyota Camry and were going to be test fitting the Yakima Quickback 2 Trunk Mounted Bike Rack, part number Y02621. To fit our bike rack, were going to open the trunk and put the safety loop inside the trunk. Well close the trunk and then well attach the top two hooks at the top edge of our trunk door. Well take the bottom hooks, attach them to the bottom of our trunk door, and side hooks to the side. Well tighten up all the straps and then well be ready to load our bike. To load our bike, well open up the arms and make them level with the ground.
Thule Raceway Trunk Bike Rack Review - 2012 Toyota Camry
Today we have a 2012 Toyota Camry and we're going to be test fitting the Thule Raceway 2 Trunk Mounted Bike Carrier, part number TH9001. To mount the Raceway we need to adjust the fit dial according to the instructions for our vehicle. Then we're going to take the top hooks and hook them at the edge of our trunk lid up by the rear windshield. We'll take the bottom clips and hook them to the underside of the trunk lid. The bottom arm of our Raceway is going to sit on the upper tier of our rear bumper. We'll use the knobs on the side to tighten our hooks down and we'll be ready to load our bike.
Yakima FrontLoader Roof Bike Rack Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, were going to be test fitting the Yakima Frontloader Roof Mounted Bike Carrier, part number Y02103. To fit our bike carrier onto our roof rack, were going to lay it on top of our crossbars. Well fit the front head over our front bar and use the hand nut to tighten it down. Then in the rear, were going to fit the clamp around our crossbar and tighten it down with the wing nut. Once weve done that, were ready to load our bike. Well take the front wheel hoop and push it open.
Yakima ForkLift Roof Mounted Bike Rack Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, were going to be test fitting the Yakima Fork Lift Roof Mounted Bike Carrier, part number Y02098. To mount our bike carrier up on the roof, first well remove the front skewer and open up the front clamp as well as the rear clamp. Well position the bike rack on top of our crossbars, close the clamps, and tighten them down with the wing nuts. Once weve done that, we can reinstall the skewer upfront and undo our wheel strap in the back. Well lift our bike up and set the rear wheel in the tray on the bike rack. Well then set our front fork into the skewer and secure it using the skewer.
Yakima Roof Rack Fairing Review - 2012 Toyota Camry
Today, we have a 2012 Toyota Camry and were going to be test fitting the Yakima 44-inch fairing for Yakima roof racks, part number Y07048. To mount the fairing, well attach all four clips around the front crossbar then well center the fairing from left to right, making sure its on the center of our vehicle. Well take the two carriage bolts and feed them through the clip on either end of the fairing and secure them with the wing nuts below. And with that, the fairing is installed and were ready to go. That does it for our test fit of the Yakima 44-inch fairing for Yakima roof racks, part number Y07048, on our 2012 Toyota Camry.
Thule Vertex 4 Hitch Bike Rack Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, well be test fitting the Thule Vertex 4-Bike Carrier part number TH9029. Now weve removed the adapter bar from the bike rack shank so that we can use 1 -inch on our vehicle. So were ready to go ahead and install it. Well slide the bike rack shank into the hitch, line up the hitch pinhole and install and tighten down our anti-rattle bolt. And this is what the Vertex will look like on your Camry. Well now go ahead and pull the hitch switch at the bottom of the bike rack and fold the mast down.
Thule T2 Platform Style Hitch Bike Rack Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, well be test fitting the Thule T2 Platform Style Bike Carrier part number TH917XTR. Now our vehicle is already equipped with 1 -inch hitch so were ready to go ahead and fit it to the vehicle. Well slide it to the bike rack shank into the hitch, line up the hitch pinhole and install our anti-rattle bolt. With the bolt tight, this is what your bike rack will look like secured to the vehicle. Now well go ahead and unfold the platform and open the trunk. And as you can see, we can gain full cargo access with this bike rack.
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Toyota Camry
Today we have a 2012 Toyota Camry and well be test fitting the Thule SUP Taxi Stand-Up Paddle Board Carrier part number TH810. To fit the carrier on our roof rack, well take the first half, set it on top of our front load bar and well wrap the speed link strap straps around the bar and seat them back in the head. Well then use the hand knobs to tighten it down. Well then move to the rear bar and repeat the same position with the other half of our carrier. Once weve done that, our bike carriers mount into our roof rack and were ready to load it up and hit the road. That does it for out test fit of the Thule SUP Taxi Stand-Up Paddle Board Carrier part number TH810 on our 2012 Toyota Camry..
Thule Hitching Post Pro Hitch Bike Rack Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, well be test fitting part TH934XTR, the Thule Hitching Post Pro. And our vehicle is equipped with the 1 -in hitch. So that with our bike rack assembled, were ready to go ahead and fit it to the vehicle. Well simply slide the bike rack shank into the hitch, line up the hitch pinhole and install our anti-rattle bolt. With our bolt tight, our bike is secured to the vehicle and this is what it would look like. Now well go ahead and give you a few measurements.
Thule Helium Hitch Bike Rack Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, well be test fitting the Thule Helium Aluminum 2-Bike Carrier part number TH970XT. Now to begin our test fit, well simply install the bike rack shank into the hitch, line up the hitch pin. After giving it a slight tug, well tighten down the anti-rattle knob at the back of the bike rack securing it to our vehicle. Now well go ahead and give you a few measurements. And our ground clearance at the bike rack is 9 inches and from the closest point of the bike rack to the back of the vehicle is 8 inches. Well now go ahead and pull the hitch switch at the bottom of the mast to tilt the mast down and we can open our trunk.
Thule Doubletrack Hitch Bike Rack Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, well be test fitting the Thule Doubletrack Platform Style Bike Carrier part number TH990XT. Now to begin our test fit, well simply install the bike rack shank into the hitch, line up the hitch pinhole and install our anti-rattle bolt. With our anti-rattle bolt tight, this is what it will look like on your car. Well now go ahead and give you some measurements. Its 6 inches from the closest point of the bike rack in the stored position to the back of the vehicle. We have 10 inches of ground clearance at the bottom of the bike rack and well add an additional 31 inches of overall length to the vehicle with the platform down.
Thule Domestique Roof Bike Rack Review - 2012 Toyota Camry
Today we have 2012 Toyota Camry and well be testing the Thule Domestique Fork Mount Bike Carrier part number TH513. Weve already got our bike carrier assembled according to the instructions and now were ready to fit it on top of our roof rack. Well place the rack up on top of the bars. Well fit the front clam around our front bar and the rear clamp around the rear and well tighten them down with the included Allen keys. Once weve done that, we can replace the skewer into the head of the bike rack and well be ready to load our bike. Well undo the rear wheel strap and fit the rear wheel of our bike into the tray.
Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, well be test fitting part number S64670, the Swagman XTC2. Our vehicles equipped with the 1-inch and -inch so were ready to go ahead and fit it into the vehicle. Well simply install the bike rack shank into the hitch, line up the hitch pinhole and start to tighten down our anti-rattle bolt. With our bolt tight, this is what your vehicle will look like with the XTC2 secured to it. Well now go ahead and give you a few measurements. Our ground clearance at the back of the bike rack is 16 inches and from the closest point of the bike to the back of the vehicle is 6 inches.
Swagman Titan Hitch Bike Rack Review - 2012 Toyota Camry
Today, on our 2012 Toyota Camry we'll be test-fitting part number s63410, the Swagman Titan four-bike carrier.Our vehicle is equipped with an inch and a quarter hitch so we'll remove the adaptor sleeve and we're ready to fit it into the vehicle. Well simply slide the bike rack shank into the hitch, line up the hitch pinhole and install our anti-rattle bolt. And with that our bike rack is secured to the vehicle and we can give you a few measurements.At the back of the bike rack, we have 12 1/2 inches of ground clearance and from the closest point of the bike rack to the back of the vehicle is 12 inches.We'll now pull the switch at the bottom of the mast to tilt it out and open our trunk. And as you can see, we can gain full access to the trunk with this bike rack. We'll now go ahead and pull the hitch switch at the top of the mast to bring out the door alarms. We can then undo the straps, exposing the cradles.
SportRack EZ Hitch Bike Rack Review - 2012 Toyota Camry
Today, on our 2012 Toyota Camry we'll be test-fitting part number a30901, the Sportrack two-bike bike rack. Now to begin our test fit, we'll simply slide the bike rack shank into the hitch, line up the hitch pinhole, install and tighten down our anti-rattle bolt. And with that our bike rack is secured to the vehicle and this is what it would look like on your car. Next, we'll give you a few measurements. In our ground clearance at the bike rack is 15 inches and from the closest point of the bike rack to the back of the vehicle is 9 and 1/2 inches. We'll now go ahead and fold the platform down to gain access to the trunk.
Curt Hitch Cargo Carrier Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, we'll be test-fitting part number c18145, the Curt 20x48 cargo carrier. To begin our test fit, we'll simply slide the cargo carrier shank into the hitch, line up the hitch pin hole and install our anti-rattle bolt. With the bolt tightened, this is how our cargo carrier would look like on your vehicle. Now, well give you some measurements. Form the closest point of the cargo carrier's side to the back of the vehicle is 4 inches. The exhaust on the Camry exits the passenger rear and is approximately 8 inches from the cargo carrier so there may be some heat transfer while driving down the road.
RockyMounts TieRod Roof Bike Rack Review - 2012 Toyota Camry
Today, we have with us a 2012 Toyota Camry and we're going to be test-fitting the Rockymounts Tierod roof-mounted bike rack, part number rky1014. We've already got our bike carrier assembled and we're ready to mount it up on the roof. To secure the bike carrier to our roof rack, we're going to take the two rubber-coated straps in the front, free them around the front load bar, re-attach them to the head of the bike rack and tighten them down with the included Allen wrench. We'll reinstall the head cover up at the front. Then at the rear of the bike rack, we'll fit the clamp around our rear bar and we'll tighten it down using the wing knots on the bike rack.Then we're ready to load our bike. We'll fit the rear wheel of the bike into the tray and set the front fork down on our skewer.
RockyMounts PitchFork Roof Bike Rack Review - 2012 Toyota Camry
Today, we have with us a 2012 Toyota Camry and we're going to be test-fitting the Rockymounts Pitchfork roof-mounted bike carrier, part number rky0438.To mount the bike rack to our vehicle, the first thing we need to do is remove the skewer and the cover off the head of the bike rack. We'll fit the front clamp around the front crossbar and use the included Allen wrench to tighten it around our front bar. Then we'll move to the rear, fit the clamp around the rear bar and use the wing knot to tighten down the clamp and the rear.At this point we can re-install our skewer and our cover on the head of our bike rack. We'll set the rear wheel of the bike into place on the tray and drop the front fork of the bike into the skewer. We'll secure the bike in the skewer and move back to secure the rear wheel with the strap. Once we've done that, our bikes loaded and we're ready to go.
Thule AeroBlade Traverse Roof Rack Installation - 2012 Toyota Camry
Today we have a 2012 Toyota Camry, and we'll be test-fitting the Thule Aeroblade roof rack system. We'll be using part number tharb53 for our load bars, part number th480r for our feet and feet kit part number thkit1438.This is the same install as you would do on a 2011 Toyota Camry however the bar measurements are a little bit shorter. For our front bar, we need to set our sliders at number 36 and our rear bar we need to set our sliders at number 35 1/2. We've already put the roof rack together and now we're ready to mount it up on the vehicle. The first thing we need to do is open the front door on both the passenger and the driver's side. Well take our front bar assembly, place it up on top of the roof and then we'll need to position it properly.
RockyMounts Euro PitchFork Roof Bike Rack Review - 2012 Toyota Camry
Today, we'll be test-fitting the Rockymounts Euro Pitchfork roof-mounted bike rack on our 2012 Toyota Camry. To fit the bike rack to our roof rack, first we'll need to remove the rubber stripping from the front load bar. This can either be left out or if you want to keep wind noise down, you can trim it to fit around the bike rack. Next, we'll slide the block on the underside of the head of the bike rack into our track on the front bar. Well then use the included Allen key to tighten both of the Allen bolts down to the block. We can re-install our head cover and then we can move back to the rear of the vehicle.
Rhode Gear Highway Hitch Bike Rack Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, we'll be test-fitting the Rhodegear Highway 2 Bike carrier, part number rg8015220. Now we removed the adapter spacer because our vehicle is equipped with a 1/4 hitch so we're ready to go ahead and fit it to the vehicle. We'll simply slide the bike rack shank into the hitch, line up the hitch pinhole and install our anti-rattle bolt. With our bolt tightened, this is what our vehicle will look like with our bike rack on it. Now, we'll go ahead and give you some measurements. In our ground clearance to the bike rack is 9 inches and from the closest point from the bike rack to the back of the vehicle is 8 inches.
Pro Series Q-Slot Hitch Bike Rack Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, we'll be test-fitting the Pro-series Q-slot Platform Style bike carrier, part number ps63134. Now to begin out install, we'll simply slide the bike rack shank into the hitch, line up the hitch pinhole and insert our hitch pin. That will secure our bike rack to the vehicle. Now, we'll give you a few measurements. In our ground clearance at the bike rack is one foot and from the closest point of the bike rack to the back of the vehicle is 9 and 1/2 inches. Next, we'll fold the platform down and open our trunk and as you can see we can gain full access to the cargo area with this bike rack.
Kuat Alpha Hitch Bike Rack Review - 2012 Toyota Camry
Today on our 2012 Toyota Camry, we'll be test-fitting the Kuat Alpha three-bike aluminum carrier, part number a103-white-114. With our vehicle equipped with 1/4 hitch, we're ready to begin fitting it to the vehicle. We'll simply slide the bike rack shank into the hitch, line up the hitch pinhole and install the attached hitch pin. Begin with giving it a little thug and tighten down the inner rail knob on the back of the bike rack. This is how your bike rack will look like secured to the vehicle. Now, we'll go ahead and give you a few measurements.
Thule Vertex 4 Hitch Bike Rack Review - 2004 Toyota Camry
Today on our 2004 Toyota Camry, well be test fitting the Thule Vertex 4 Bike Carrier, part number TH9029. Now, our vehicle is equipped with an 1 1/4 hitch, so we removed the adapter and were ready to install it in the vehicle. Well simply slide the bike rack shank into the hitch, line up the hitch pinhole, and insert and tighten down our anti-rattle bolt. This will secure our bike rack to the vehicle and this is what it will look like mounted to your car. Well now go ahead and give you a few measurements. Our ground clearance at the bike rack is 14 1/2 inches and from the closest point of the bike rack to the back of the vehicle is 10 inches.
Thule Hitching Post Pro Hitch Bike Rack Review - 2004 Toyota Camry
Today on our 2004 Toyota Camry, well be test fitting the Thule Hitching Post Pro, part number TH934XTR. Now, our vehicle is equipped with the 1 1/4 hitch, so we removed the adapter and were ready to fit it to the vehicle. Well simply slide the bike rack shank into the hitch, line up the hitch pinhole and install and tighten down our anti-rattle bolt. We can now give you a few measurements. Our ground clearance at the bike rack is 10 1/4 inches and from the closest point of the bumper to the front of the bike rack is 10 1/2 inches. Well now go ahead and pull the pin at the bottom of the mast to fold the mast down and open our trunk.
Thule Helium Hitch Bike Rack Review - 2004 Toyota Camry
Today on our 2004 Toyota Camry, well be test fitting the Thule Helium 2 Bike Carrier, part number TH970XT. With our vehicle equipped with 1 1/4 hitch, weve removed the adapter and were ready to fit it to the vehicle. Well simply slide the bike rack shank into the hitch, line up the hitch pinhole and install our integrated hitch pin. After giving it a slight tug, well go ahead and tighten down the anti-rattle knob, securing it to the vehicle. Now well go ahead and give you a few measurements. Our ground clearance at the bike rack is 10 inches and from the closest point of the vehicle to the bike rack mast is also 10 inches.
Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2004 Toyota Camry
Today on our 2004 Toyota Camry, well be test fitting the Swagman XTC-2, part number S64670. Now, our vehicle is equipped with 1 1/4 hitch so weve gone ahead and removed the adapter and were ready to fit it to the vehicle. Well simply install the bike rack shank into the hitch, line up the hitch pinhole and insert and tighten down our anti-rattle bolt. Well now give you a few measurements. Our ground clearance at the bike rack is 14 1/2 inches and from the closest point of the bike rack to the back of the vehicle is 5 inches. We can now go ahead and unfold the platform and open our trunk.
SportRack EZ Hitch Bike Rack Review - 2004 Toyota Camry
Today, we have a 2004 Toyota Camry and were going to be test fitting the SportRack 2 Hitch Mounted Bike Carrier, part number A30901. To pin our bike rack onto the vehicle, well take the shank and put it in the receiver of our hitch. Well line up the hitch pinholes and then well put our anti-rattle bolt into the bike rack. Well use a 3/4-inch wrench to tighten it down. With our bike rack secured, we can check for rear vehicle access. Well fold down the wheel trays and pull down the upright mast to make sure we can still open the trunk and get into the rear of the vehicle.
Rhode Gear Highway Hitch Bike Rack Review - 2004 Toyota Camry
Today on our 2004 Toyota Camry, well be test fitting the Rhode Gear Highway 2 Bike Carrier, part number RG8015220. Now, our vehicle is equipped with 1 1/4 hitch so we remove the adapter and were ready to go ahead and fit it to the vehicle. Well simply install the bike rack shank into the hitch, line up the hitch pinhole and install and tighten down our anti-rattle bolt. And that will secure our bike rack to the vehicle. Now well go ahead and give you a few measurements. Our ground clearance at the bike rack is 10 1/2 inches and from the closes point of the bike rack to the back of the vehicle is 6 1/2 inches.
Kuat Alpha Hitch Bike Rack Review - 2004 Toyota Camry
Today, we have a 2004 Toyota Camry and were going to be test fitting the Kuat Alpha Aluminum Bike Rack, part number A103-WHITE-114. To mount the bike rack to the vehicle, were going to align the shank of the bike rack up with the hitch. Well slide the shank in and line up our hitch pinholes. Once the hitch pinholes are aligned, we can turn the knob at the end of the shank to engage the anti-rattle device. Once we have that snugged down, we can go ahead and insert our pin through the pinholes, securing the bike rack to the vehicle. Next, well check for rear vehicle access.
WeatherTech Front Floor Liners Review - 2011 Toyota Camry
Today in our 2011 Toyota Camry, we're going to do a test fit of the Weather Tech floor mat, part number WT440841. These will be for the front row, black in color. This set is a two-piece set, one liner for the driver's side and one liner for the passenger side. First we'll go ahead and remove the older manufacture floor mat inaudible 00:00:22. Now we've already installed the new floor liner. As you can see, the new liner is custom molded to precisely fit the vehicle and stay in place.
Husky Cargo Floor Liner Review - 2011 Toyota Camry
Today on our 2011 Toyota Camry, we're going to do a test fit of the Husky Floor Liner in the rear cargo area, part number HL44501, black in color. Now for this application, there's no old liner to remove so we're ready to go ahead and install the new liner. The Husky Liner is custom molded to precisely fit the vehicle and stay in place. The shape, channels, and moldings all work to keep dirt and debris contained in the liner and off the carpeting. As you can see, this liner is molded with the interior lining of the rear cargo area and it even has a precise cutout around the rear storage compartment. As you can see, the liner is easy to install and can also be easily removed and cleaned with soap and water.
WeatherTech Front Floor Liners Review - 2009 Toyota Camry
Today in our 2009 Toyota Camry we will go to be testing the WeatherTech Front liner in the front row Part No. WT440841; black in color. WeatherTech liners are custom molded precisely to fit the vehicle and stay in place. The shape channels and moldings always hit dirt breaking contained in the liner and off the carpeting. As seen here with the tall sidewalls, the molded areas to attach to the manufacturers mounting point and a cutout around the drivers side handles for the gas and trunk latch. Youll notice the cutout around the drivers seat post and the fly cutout around the passengers seat mounting point.
Husky Cargo Floor Liner Review - 2009 Toyota Camry
Today on our 2009 Toyota Camry we are going to be test fitting the Husky Floor Liner in the rear cargo area part number HL44501 black in color. First we will go ahead and remove the old or manufacturers cargo lining. Now we are ready to install the husky floor liner. Husky liners are custom molded to precisely fit the vehicle and stay in place. The shape, channels and moldings all work to keep dirt and debris contain in the liner and off of the carpeting. As seen here, it has the molded lip around the outside to contain the dirt and debris inside and fits the outline of the rear cargo area.
Yakima Q Tower Roof Rack Installation - 2010 Toyota Camry
Alright on this 2010 Toyota Camry we're going to do a test fit of the Yakima Q Tower system with part numbers Y00124 Q5 and Q35. We'll start off with our crossbars already assembled according to the instructions and open the front doors. Now I can place the front crossbar on top of the vehicle. To place it properly, we will measure from the edge of the windshield to the leading edge of the tower. Now let's go by the manufacturer's instructions, in this case the measurement will be 9 inches. With the from bar in place we can move on to the rear.
Thule Traverse Roof Rack Installation - 2010 Toyota Camry
Today, on this 2010 Toyota Camry, we are going to do a test fit of a Thule Traverse roof rack. Well be using Thule Traverse foot pack and a 50-inch Thule square low bars. We have our low bars pre-assembled according to the instructions, so Ill mount them up onto the vehicle and test them out. Well start off with the doors open and place the front low bar onto the roof. To properly position the bar, well measure from the trim edge of the wind shield to the leading edge of the foot pack. Always go by the instructions, in this case we will use the measurement of 9 inches.
Thule AeroBlade Traverse Roof Rack Installation - 2010 Toyota Camry
Today, on this 2010 Toyota Camry, well be doing a test fit of a Thule Aeroblade roof rack with the diverse foot packs. Well start off with the bars already assembled and well place them on top of the vehicle. To position the bars properly well measure from the edge of the wind shield to the leading edge of the foot pack. Always go by the instructions, however this measurement will be 9 inches. To position our rear bar, we are going to measure from the center of the front bar to the center of our rear bar. This measurement will be 26 and inches.
Yakima StickUp 2 Hitch Bike Rack Review - 2011 Toyota Camry
Today on our 2011 Toyota Camry well be test fitting part #: y02420, the Yakima stick up tube hitch mounted bike rack. Now our vehicle is equipped with the inch and a quarter hitch and our bike rack is already preassembled so were ready to go ahead and fit it to the vehicle. Well insert the bike rack shank into the hitch, well then line up the hitch pinhole and insert our anti-rattle bolt. Well then need to tighten down the anti-rattle bolt with the wrench and with it tight well install our safety pin. And that will secure our bike rack to the vehicle. With our bike rack secured to the vehicle well go ahead and give you a few measurements.
Thule Vertex 4 Hitch Bike Rack Review - 2011 Toyota Camry
Today on our 2011 Toyota Camry were going to do a test fit of the Thule Vertex 4 bike carrier part #: th9029. Our vehicle is equipped with an inch and a quarter inch hitch and with our bike rack already preassembled well go ahead and remove the 2 inch bushing so that the bike rack shank will slide directly into the inch and a quarter inch receiver tube. So now were ready to go ahead and install the bike rack onto the vehicle sliding the shank into the receiver tube and installing and tightening down the anti-rattle bolt. As you can see with the anti-rattle bolt tightened down, it really takes out any sway or rattle between the bike rack and the hitch. This is what our bike rack will look like when its in the stored position. Now well go ahead and take a couple of measurements, from the nearest point of the bumper to the bike rack we have 4 inches and from the lowest point of the bike rack to the ground we have 10 inches of ground clearance.
Thule T2 Platform Style Hitch Bike Rack Review - 2011 Toyota Camry
Today on our 2011 Toyota Camry well be test fitting the Thule T2 platform bike carrier part #: th917xtr. Now, our bike rack is already preassembled and our vehicles equipped with the inch and a quarter hitch, so were ready to go ahead and fit it to the vehicle. Well simply insert the bike rack into the hitch, well line up the hitch pinhole and install our anti-rattle bolt. Well then tighten it down with a wrench and that will secure our bike rack to the vehicle. Well go ahead and give you a few measurements. Now, our ground clearance on this vehicle is 11 and a half inches and from the closest point of the bike rack to the back of the vehicle is just a mere few eights of an inch.
Thule Apex 4 Hitch Bike Rack Review - 2011 Toyota Camry
Today on our 20011 Toyota Camry were going to do a test fit of the Thule Apex 4 bike carrier part #: th9025. Our vehicles equipped with an inch and a quarter hitch, so with our bike rack already preassembled well need to remove the 2 inch by 2 inch bushing so the bike rack shank will slide directly into the receiver tube. As we slide the shank into the receiver tube well line the integrated hitch pin up with the receiver tube holes, then use the hand knob to secure the bike rack to the hitch. Now with our rack in a stored position were going to go ahead and take a couple of measurements. From the closest point of the bumper to the bike rack is 4 inches. From the lowest point of the bike rack to the ground we have 10 inches of ground clearance.
SportRack EZ Hitch Bike Rack Review - 2011 Toyota Camry
Today on our 2011 Toyota Camry we'll be test fitting the SportRack 2 Hitch Mounted Bike Rack, part number A30901. A quick note about this bike rack, it will fit either 1-1/4 or 2-inch hitches. Our vehicle is equipped with the 1-1/4-inch hitch and our bike rack is preassembled so we're ready to go ahead and fit it to the vehicle. We'll begin by simply inserting the bike rack shank into the hitch. We'll line up the hitch pin hole and insert our anti-rattle bolt. We'll then tighten it down with a wrench.
Rhode Gear Highway Hitch Bike Rack Review - 2011 Toyota Camry
Today on our 2011 Toyota Camry, we'll be test fitting the Rhode Gear Highway 2 Bike Carrier, part number RG8015220. Now, our bike rack is already pre-assembled and our vehicle has an 1-1/4-inch hitch, so we're ready to go ahead and fit it to the vehicle. We'll insert the bike rack shank into the hitch. We'll line up the hitch pinhole and insert our anti-rattle bolt. We'll then tighten it down with a wrench. With the anti-rattle bolt tight, we can install our safety pin on the other side and that will secure our bike rack to the vehicle.
Rola Roof Cargo Basket Installation - 2011 Toyota Camry
Today on our 2011 Toyota Camry, we'll be test fitting the Rola Roof Mounted Cargo Basket, product number 59504. With our vehicle equipped with the Akima Roof Rack and our basket already pre-assembled, we're ready to go ahead and fit it to the vehicle. We'll begin by placing the basket on top of the crossbars. We'll center it from left to right with the vehicle. From that point, we can tighten it down using the included hardware. With the wind nuts tight, our cargo carrier is secured and we're ready to go ahead and load it up.
Rola Roof Cargo Basket Installation - 2011 Toyota Camry with AeroBlade Roof Rack
Today, we'll be test fitting the Rola Roof Mounted Cargo Basket, product number 59504, on our 2011 Toyota Camry. Our vehicle is already equipped with a roof rack mounting system and our cargo basket is already pre-assembled, so we're ready to go ahead and fit it to the vehicle. We'll begin by placing the cargo basket on top of the crossbars. We'll center the basket from left to right with the vehicle. We'll then tighten it down using the included hardware. With our hardware tight, our cargo basket is secured and we're ready to go ahead and load it.
Yakima Q Tower Roof Rack Installation - 2011 Toyota Camry
Today on our 2011 Toyota Camry well be test fitting the Yakima Q Tower roof rack, using part numbers Y00124, Y00409, Y00605 times two, Y00635 times two. With our roof rack already preassembled were ready to go ahead and fit it to the vehicle. Well start by opening up the doors to allow access to the door openings. With the door open were ready to go ahead and set the bar on top of the vehicle. Well start with the front bar. In orde to fit the front bar in its proper location well need to take a measurement.
Thule AeroBlade Traverse Roof Rack Installation - 2011 Toyota Camry
Today in our 2011 Toyota Camry well be test fitting the Thule aero blade traverse roof-rack part numbers TH480R and THARB53. Well be using the 53-inch crossbars with our roof-rack already preassembled, were ready to go ahead and fit it into the vehicle. Well begin by placing the front bar on top of the roof in order to get our proper location. Well need to do a measurement. The front crossbar will be nine inches from the top of the windshield. So well measure from the top of the windshield nine inches back on the roof in that will be where the leading edge of the front crossbar tower will set.
Thule MOAB Roof Top Cargo Basket Review - 2011 Toyota Camry
Today, on our 2011 Toyota Camry, we'll be test fitting the Thule MOAB Roof Top Cargo Carrier, part number TH690. Our vehicle is already equipped with the Thule AeroBlade Roof Rack system and our basket is already preassembled. We'll ready to go ahead and fit it to the vehicle. We'll began by placing the basket on top of the cross bars. We'll center it from left-to-right. We'll then tighten it down using the included hardware.
Thule Doubletrack Hitch Bike Rack Review - 2010 Toyota Camry
Today on this 2010 Toyota Camry we're going to do a test fit of product number TH990XT Thule Doubletrack Platform Bike Carrier. This bike carrier will fit 1-1/4 inch receiver hitches both class 1 and class 2 but it also with this base and it can work with 2-inch trailer hitches. In this application we'll be working with a class 2 hitch. We'll go ahead and install the rack into the hitch and then line up the hitch pin holes. And then we'll put it in to Snug-Tite Lock. We'll go ahead and install the rack into the hitch and line the hitch pin holes.
Rhino-Rack Aero Roof Rack Installation - 2010 Toyota Camry
Today on this 2010 Toyota Camry we're going to install the Rhino Rack Roof Rack. Product number DA118 for the crossbars and DK114 for the clamp kit. For our quick test fit we went ahead and assembled the crossbars as described in the instructions and we'll just place them on the vehicle and see how it looks. We'll start off with the front crossbar. Let's lay it on the roof and we'll move it into its final position. To place the front rail we're going to measure from the center of the rail over to the center of the door jamb.
Trailer Hitch Installation - 2007 Toyota Camry
Today were working on a 2007 Toyota Camry. Were going to install Draw Tite Hitch part number 36416. This will also be comparable to Hidden Hitch part number 90152. Here are a couple of measurements that will assist you when selecting new accessories for your hitch such as a draw bar, a bike rack, or a cargo carrier. From the center of the pin hitch hole to the outer most point of the bumper is 4-3/4, from the top of the receiver tube to the ground is 11. Now lets go ahead with the installation.
Trailer Hitch Installation - 2010 Toyota Camry
Today were working on a 2010 Toyota Camry. Were going to install a Draw Tite Hitch part number 36416. This will also be comparable to Hidden Hitch part number 90152. Here are a couple of measurements that will assist you in selecting accessories for your new hitch such as a draw bar, a bike rack, or a cargo carrier. From the center of the pin hitch hole to the outer most point of the bumper is 4-3/4 inches. From the top of the receiver tube to the ground is 10-1/2 inches.
Thule Doubletrack Hitch Bike Rack Review - 2007 Toyota Camry
Today on this 2007 Toyota Camry were going to do a quick test of part number TH990XT from Thule. This is Thules Doubletrack Platform Bike Rack. We will line up the pin hitch holes and install the anti-rattle bolt. Now Thule does provide a tool to tighten down the bolt, however a inch wrench works just as well. On the other side of the bolt we will add our lock, and were secure to the hitch. Alright now we will give you some measurements that will give you an idea of clearance between a bicycle rack and a vehicle, and the bicycle rack and the ground.
Trailer Wiring Harness Installation- 2011 Toyota Camry
Today on this 2011 Toyota Camry we are going to install part number 118482 from Tow Ready. First thing we need to do is get access to the wiring harness, we are going to have to open the trunk and remove the rear threshold and interior components. We are also going to have to move these hooks and to move those you push down on the center right here and then you can pull it apart. Then remove the threshold. Now just pull back the interior carpeting to get access to the wiring harness. That is looking at the drivers side and then repeat the same process on the passengers side. Then we can start installing the T-connector now. 0:52
Trailer Hitch Installation - 2010 Toyota Camry
Today we are going to be working on a 2010 Toyota Camry. We are going to be installing Curt hitch part number 12343. Here are a couple of measurements for your new hitch. From the center of the hitch pin hole to the outermost point of your bumper is 2 inches. From the top of the receiver tube to the ground is 12 inches. Now let us go ahead and start our installation. 0:26
Trailer Wiring Harness Installation - 2011 Toyota Camry Hybrid
Today we will be working on a 2011 Toyota Camry Hybrid. We will be installing Tow Ready T-One Connector, part number 118482. For ease of installation, I recommend to remove the spare tire and trays. This will help you in gaining access behind the taillights for installation of your new T-one connector. First we are going to remove the cargo carrier tow hooks. Now that you have your cargo carrier hooks out of the way, we can remove our trim panel. You will see that this will give us access to peel back our carpet line and access our connector. Gently push down on the tab. Pop it free from the socket. And then we are going to use our new connector. Push them together firmly so they snap in place. You will see we have now installed our new harness in line with the vehicles current wiring harness. 0:54
Trailer Hitch Installation - 2009 Toyota Camry
Today we are going to be installing Draw-Tite hitch part number 36416 on a 2009 Toyota Camry. This hitch installation will also apply for Hidden Hitch part number 90152. OK, the first thing we want to do is to open up the trunk. And we need to remove our spare tire, because we will be drilling some holes through the spare tire well. As you can see here on the passengers side, we are going to need to actually lower the exhaust. You want to go ahead and use a strap or something to hold the exhaust up, because once you remove the final hanger, it will considerably. We are also going to go to the forward side of the exhaust. We need to remove the exhaust off the rubber hangers here, and here as well. You can see we have a reinforcing bracket that we are going to need to remove. And with the exhaust lowered and the brackets removed, we can go ahead and point out the mounting location for the trailer hitch. We have got two weld nuts here in this bumper flange that we are going to go ahead and use as two of the attaching points on each side. Once we get the hitch mounted into these weld nuts, there are two tabs that are going to be going into the spare tire well - which, we are are going to use the hitch as a template and drill holes through there. Then next, we want to go ahead and remove the two fascia clips here at the bottom of the bumper. When we mount the hitch, it will allow the cross tube to go up and behind the bumper.
Trailer Hitch Installation - 2009 Toyota Camry
Today we are going to be installing Curt hitch part number 12343 on a 2009 Toyota Camry. We are underneath the vehicle now, and I am going to go ahead and point out the mounting location for the trailer hitch before we get started. As you can see here on the passengers side, we have got the main exhaust. There are three bolts here at the bottom of the frame holding the exhaust bracket on. We are going to to need to remove those, and the hitch is actually going to go up in that same mounting location, using those same three holes. It is also going to use the weld nut here on the vertical flange here, nearest the bumper. You can see we have a reinforcing bracket that we are going to need to remove there are three bolts to take that off. The attaching points, again, on the drivers side, we are going to be using this same vertical flange. We are going to use this existing weld nut, and this one as well. This one you can see is covered by tape, so we are going to need to remove that first. And then this tab on the outboard side of the frame as well. And again, I am just cutting out the sticker to expose the weld nut and the frame. Some of these exposed weld nuts might have a considerable amount of corrosion in them. If that is the case, you want to go ahead and spray them down with some sort of lubricant, and maybe get a wire brush in there to clean them out really well before you get started.
Trailer Hitch Installation - 2003 Toyota Camry
Today we are going to install part number 12339 from Curt, and we are going to install this on a 2003 Toyota Camry. Before we begin our install, we will show you exactly where the hitch will mount up on the vehicle. First off, on the passengers side, it will mount up on these three bolts right here. We have taken these three bolts - one, two, three - and those will be replaced with the bolts that came with the hitch. Moving over to the drivers side, there will be couple of different varieties, depending on the vehicle you have. They will always have these two holes right here. On some varieties, there will be no holes here or maybe two existing holes. Or, in this case, there is actually one hole underneath the sticker right here. You will not actually know until you look underneath the vehicle. And there is a threaded bolt hole. So, in this case, we will only be using these three holes.
Trailer Hitch Installation - 2005 Toyota Camry
Today we are going to install part number 36336 from Draw-Tite on an 2005 Toyota Camry. The first thing we will to show you is where the hitch mounts on the frame. And the hitch will mount on the frame here using these two bolt holes for sure. However, on some models there may be no more bolt holes, and there might be an extra one here. In this case, see? There is like a black sticker covering the hole. We will check it out and see if this is a threaded hole. If so, we can actually use that. If your vehicle does not have this threaded hole here, then you just drill out two holes using the hitch as a template and then put a U-bolt inside. We will see what we have got here. And it looks like this is a threaded hole. So on this side we will be using three attaching points. On the passengers side, with the exhaust here, we have to take down these two bolts, and then the hitch goes in this place. And then the exhaust bracket actually bolts on top of the hitch.
Trailer Wiring Harness Installation - 1998 Toyota Camry
Start by entering the trunk and you want to remove the access panels that allow you access to the rear of the taillights there is one on each side, there are three fasteners holding it on. Once you remove the interior panels pull your carpet back and you need to remove the metal threshold piece as well. There are two fasteners attaching it, and it is just pop riveted on.
