Pontiac Bonneville owners are most interested in these products

Pontiac Bonneville Questions and Answers

Parts needed to Carry a 2010 Harley Davidson Ultra Classic and Flat Tow a 2002 Pontiac Bonneville
There are two options. First, you can install the Blue Ox 3-receiver hitch, # SC9000. Installation of the receiver may require modification of mount plates or fabrication of new mount plates depending on the coach and chassis. Welding the mount plates to the 3 receiver weldment is also required. The receivers should be positioned so that they are between 16 and 18 inches on center from the ground and so that it or the carrier mounted in it does not interfere with the coach bumper body or exhaust
view full answer...

Installation Hardware Included with Air Lift # AL60798 or Firestone # F4107 for 1999 Bonneville
Either system includes all necessary valves, air lines and hardware for a manual inflation installation. The bags are installed and the lines are then ran to a protected, accessible area. In a sedan like your Bonneville, installing the inflation valves in the trunk is the best bet. The two systems are very similar and would function alike. Although Firestone is the familiar and trusted household name, from personal experience I can state that the customer service provided by Air Lift is super
view full answer...

Trailer Wiring Harness for a 1999 Pontiac Bonneville
The only wiring harness we carry for the 1999 Pontiac Bonneville is the Upgraded Circuit Protected Taillight Converter Hardwire Kit, # 119175KIT. A T-one style connector is not available. Installation of this kit is still very simple. Using the included circuit tester, you will test the wires behind each tail light and find the ones for brake lights, running lights, and left turn signal on the driver side, and right turn on the passenger side. once you have found the correct wires they wil
view full answer...

Will the Draw-Tite Class III Trailer Hitch # 75146 Fit on a 1970 Bonneville 455
We do not carry hitches for the 1970 model Bonneville. The oldest model we have at this time is 1977 and the hitch design is definitely not going to match the frame on your 1970 model vehicle. We do have the Custom Built Class IV Ultra Frame Trailer Hitch, item # 41990 or 41991, which could be used along with the 7 inch Weld-on Bracket Kit for Class IV Ultra Frame Trailer Hitch Receiver, item # 4907, to install a receiver hitch on your vehicle. This is a custom weld on application and will re
view full answer...

Which Trailer Hitch Should I use for a 1992 Pontiac Bonneville to a Tow a 3,000 Pound Casita
Class I hitches typically have a maximum towing capacity of 2,000 pounds and Class II typically have a total capacity of 3,500 pounds. You will need to use a Class II hitch on your Bonneville to tow your trailer. Remember to also check the towing capacity listed in your vehicle owner manual. The vehicle may be capable of less than the hitch in which case you would need to abide by the vehicle tow rating. The highest capacity hitch we would offer for your 1992 Pontiac Bonneville will tow up to
view full answer...

Trailer Hitch for a 1994 Pontiac Bonneville SSE
We offer a hitch that would fit your 1994 Pontiac Bonneville SSE. The Draw-Tite Class II Receiver Hitch, part # 36216 is custom designed for your vehicle. With this hitch, the manufacturer recommends the Class II draw bar, part # 36061. You will need a pin and clip, part # PC2 to secure the draw bar into the receiver, or a locking hitch pin, part # RH2-XL. If you need a trailer ball, we offer the 2 inch ball, part # 19258 or the 1-7/8 inch ball, part # 19256. To wire your Bonneville for towing,
view full answer...

Replacement Hardware Kit for Draw-Tite Class II Trailer Hitch, Part # 36211
We do offer replacement hardware. The part # is RHK. All you need to do is enter the part number and manufacturer of the hitch into the appropriate fields.
view full answer...