Select Your Vehicle

View Cart


Nissan Titan owners are most interested in these products

or change vehicle




Nissan Titan Videos

Rain-X Weatherbeater Wiper Blades Installation - 2012 Nissan Titan

Today on this 2012 Nissan Titan we're going to do a test fit of part number RX30224 from Rain-X. This is a Weather Beater windshield wiper blade. The things to know about this part. That is designed to be an OEM replacement blade. The rubber squeegee has UV inhibitors to protect you from the sun light. It is a frame style design that gives it multiple pressure points against the windshield. Now to start off our test fit we're go ahead and remove the original windshield wiper blades. First of all tab we have to push and we can go ahead and release them.



Trailer Brake Controller Installation - 2004 Nissan Titan

All right, today on our 2004 Nissan Titan, we're going to install part number 90195 from Tekonsha. It's the P3 Brake Controller. Now this truck does come with a tow package already installed on the vehicle however, this model's an XE model. This port is different from the other Titan models and the plug-in for it is not readily available. So, we're going to bypass the port and go ahead and hard-wire our brake controller in. First off we need to get access to the port. It'll be behind a kick panel right next to the parking brake.



U-Ace 3D Kagu Custom Front and Rear Row Floor Liner Review - 2010 Nissan Titan

Today on our 2010 Nissan Titan, we'll be test fitting the U-Ace 3D Kagu custom auto floor liners, with max spider grip, in black. Part number L1NS05101509, also available in beige, part number L1NS05101502, and in gray L1NS05101501. We will start by removing the factory floor mats. We can now put our new floor mat in place. With our floor mat in place, you can see this is a vehicle specific application and that the mat is contoured to match the interior of our vehicle. The mat features raised containment walls to keep what ever dirt and debris you may bring into the vehicle off of the carpets and onto the mat. We have the added protection up underneath the pedals and on the left side of the vehicle. We have the molded texture on the mat for a little extra grip and we have the heel pad molded into the center of the mat to provide some extra grip. We also have the raised bumps on our mat to sit over the factory mounting points for the factory floor mats.



Carr Light Wing Off-Road Light Mounting System Installation - 2010 Nissan Titan

Today on our 2010 Nissan Titan well be installing the Carr Light Wing off-road light mounting system, part number: CARR167301.Now, the first step to installing the light mount is to find the center of the bumper. On our Nissan, were going to go to the center section of the bumper, measure across to find the center and then well mark it. Just use our tape measure and run it across the center section of the bumper.Next, well take a marker and mark the center point. With our center point marked we now want to take our light mount, line it up with the center of the car and determine the height that we want to put our light mount at. Well just use the center mounting hole, find our center mark and work straight down. Until were at the height that we want.Once there well mark our center again, double check our measurement and get ready to drill.



Trailer Connector Socket Installation - 2010 Nissan Titan

Today in this 2010 Nissan Titan, we're going to install part number Hm40975 from Hopkins. This is a replacement multi-tool 7-way and 4-way trailer connector. To stat off our install we're going to go ahead and remove the original, simple connector bits on our truck. We take a small screwdriver and push in one of the tabs located off to the side, then we'll go ahead and rotate the connector. That'll release it from the bracket. Now we need to disconnect the electrical. There's a small tab behind the connector that we have to push down and it comes apart. At this point we can go ahead and start working on our new 7 pull connector.



Trailer Hitch Installation - 2014 Nissan Titan - Draw-Tite

Today, on our 2014 Nissan Titan, we'll be installing the Draw-Tite Hitch, part number 41551. This is what our hitch should look like once it's installed. Next, we'll go ahead and give you a couple measurements to assist your selecting accessories for your new hitch. From the center of hitch pin hole to the outermost edge of the bumper is 3 inches. From the top of the receiver tube to the ground is 21 and a 1/2 inches. This will assist your selecting accessories; such as a ball mount, bike rack, or cargo carrier. Now, we'll go ahead with the installation. To begin our install, we'll first go ahead and point out the attachment points.



Softride Dura Hitch Bike Rack Review - 2014 Nissan Titan

Today on our 2014 Nissan Titan, we're going to be test fitting the Softride Dura Parallelogram, a tilting 4-bike rack for inch-and-a-quarter and 2-inch hitches, part number Sr26247. To begin our test fit, we'll slide the shank of the bike rack into the receiver tube of our hitch, line up our pin holes, thread in our anti-rattle bolt, and tighten it down with a wrench. We can then secure it, using the provided lock. In this position, we'll have about 19 inches worth of ground clearance. The closest point of the rack to the back of our vehicle is about 6 inches away, and overall, we've added about 35-1/2 inches to the length of the truck. The Dura Parallelogram has removable arms that allow for more storage options.



Saris Freedom Hitch Bike Racks Review - 2014 Nissan Titan

Today on our 2014 Nissan Titan, we're going to be test fitting the Saris Freedom. A platform style four bike rack for two inch hitches. Part number SA4414B. To begin our test fit, we'll slide the shank of the bike rack into the receiver tube of our hitch, line up our pinholes, thread in our anti-rattle bolt and tighten it down with a wrench. We'll then secure it using the provided clip. In this position we'll have about 19 inches worth of ground clearance. The closest point of the rack to the back of our vehicle's about four and a quarter inches away.



Saris Axis 3 Bike Rack Review - 2014 Nissan Titan

Today on our 2014 Nissan Titan, we're going to be test fitting the Saris Axis, a tilting 3-bike rack for inch-and-a-quarter and 2-inch hitches, part number SA843B. To begin our test fit, we'll slide the shank of the bike rack into the receiver tube of our hitch, line up our pin holes, thread in our anti-rattle bolt, and tighten it down with a wrench. We'll then secure it using the provided lock. In this position, we'll have about 19-1/2 inches worth of ground clearance. The closest point of our rack to the back of our vehicle is about 6 inches away, and overall, we've added about 13-1/2 inches to the length of the truck. Pulling the yellow T-handle at the base of the center mast, will allow us to tilt it away from our vehicle.



Saris Axis Tilting 2 Bike Rack Review - 2014 Nissan Titan

Today on our 2014 Nissan Titan, we're going to be test fitting the Saris Axis, a tilting 2-bike rack for inch-and-a-quarter and 2-inch hitches, part number SA832. To begin our test fit, we'll slide the shank of the bike rack into the receiver tube of our hitch, line up our pin holes, thread in our anti-rattle bolt from the left to the right, and tighten it down with a wrench. We can then secure it with the provided clip. In this position, we'll have about 19-1/2 inches worth of ground clearance. The closest point of the rack to the back of our vehicle is about 6-1/4 inches away, and overall, we've added about 12 inches to the length of our Titan. Pulling the yellow T-handle at the base of the center mast, will allow us to tilt the rack away from our vehicle.



Thule Helium Aero Hitch Bike Rack Review - 2014 Nissan Titan

Today on our 2014 Nisan Titan, were going to be test fitting the Thule Helium Aero, a tilting two bike rack for 1-1/4 and 2 inch hitches, part number TH9042. To begin our test fit, well slide the shank of the bike rack into the receiver tube of our hitch. As we do this, well want to hold out on the attached pin. Well line up our pin holes. Allow the attached pin to fall into the pin hole. Well then turn the black knob.



SportRack 3 Bike Rack Review - 2014 Nissan Titan

Today on our 2014 Nissan Titan, we're going to be test fitting the Sportrack Tilting 3 Bike Rack for 1 1/14 and 2 inch hitches, part # SR2403. To begin our test fit, we'll slide the shank of the bike rack into the receiver tube of our hitch, line up our pinholes, thread in our anti-rattle bolt and tighten it down with a wrench. We can then secure it with the provided clip. In this position, we'll have about 19 1/4 inches worth of ground clearance. The closes point of the rack to the back of our vehicle is about 3 3/4 of an inch away, and overall we've added about 11 1/2 inches to the length of our truck. Pulling the black pin and clip at the base of the rack will allow us to tilt it away from our vehicle. As you can see, this allows us to fully open our tailgate. With our mast back in its upright position, we'll now pull the pin and the clip at the top of the rack.



Softride Hang2 Tilting Bike Rack Review - 2014 Nissan Titan

Speaker: Today on our 2014 Nissan Titan, we're going to be test-fitting the Softride Hang 2, a tilting two bike rack for 1 1/4" and 2" hitches, Part#SR27041. To begin our test fit we'll side the shank of the bike rack into the receiver tube of our hitch. Line up the pinholes. inaudible 00:00:20 our anti-rattle bolt and tighten it down with a wrench. In this position we have about 19 1/4" worth of ground clearance. The closest point of the rack to the back of our vehicle is about 4 1/2" away. And over-all we've added about 20 1/2" to the length of the Titan. Pulling the two pins at the top of the mass will allow us to swing our handle bar cradles up into position.



Softride Element Hitch Mounted Bike Rack Review - 2014 Nissan Titan

Today on our 2014 Nissan titan were going to be test fitting the Softride Element Parallelogram. A tilting 4 bike rack with 1 1/4 inch 2 inch 00:00:08 hitches part number SR26248. To begin our test fit, were going to side the shank of the bike rack into the receiver tube of our hitch, line up our pin holes, tread in our anti-rattle bolt and tighten it down with a wrench. In this position we have about 19 inches worth of ground clearance. Closest point of the rack to the back of our vehicles is about 4 inches away and overall weve added about 12 inches to the length of the truck.Pulling the silver pins at the top of the mast will allow us to swing out our cradle arms. Well rotate them into position and reinsert the pins into the new holes to secure them.



Saris Thelma 3 Bike Rack Review - 2014 Nissan Titan

Today on our 2014, Nissan Titan. We're going to be test fitting the Saris Thelma. A platform style 3-Bike rack for inch of a quarter and two inch hitches, part number SA4239B. To begin our test fit, we'll slide the shake of the bike rack into the receiver tube of our hitch. Lineup our pin holes, throw out in our anti rattle bolt and tighten it down with our wrench. We can then secure it using the provided clip. This position, we'll have about 19 in a quarter inch worth of ground clearance.



Pro Series Eclipse 4 Hitch Bike Rack Review - 2014 Nissan Titan

Today on our 2014 Nissan Titan, we're going to be test fitting the Pro Series Eclipse, a tilting forward bike rack for 2 inch hitches, part number 63124. To begin our test fit, we'll slide the shank of the bike rack into the receiver tube of our hitch, line up our pin holes, drive in our anti-rattle bolt, and tighten it down with a wrench. We can then secure it using the provided clip. In this position we'll have about 19 and a quarter inches worth of ground clearance. The closest point of the rack to the back of our vehicle is about 5 and a quarter inches away. Overall we've added about 29 inches to the length of our Titan. Pulling the silver pin at the base of the mast will allow us to tilt it away from our vehicle. As you can see we cannot fully open our tailgate. With our mast back in its upright position, it's now time to load our bike.



Hollywood Racks Traveler Tow n Go Bike Rack Review - 2014 Nissan Titan

Today on our 2014 Nissan Titan we're going to be test fitting the Hollywood Racks Traveler Tow-n-go 3 bike rack for 2 inch ball mounts, part number HR135. For today's test fit, we'll be using the Hidden Hitch ball mount with an extra long shank, part number 80232. We'll begin our test fit by sliding the shank of the ball mount into the receiver tube of our hitch, lining up our pin holes, sliding through a pin, and securing it with a clip. Now please keep in mind the ball mount, the pin and clip, and the hitch ball are all sold separately. As you can see, using the standard pin and clip does leave some play in our bike rack. If you'd like to secure it further, we do have anti-rattle devices. Just check our website for some more details. Now it's time to swing out our dual cradle arms.



Trailer Hitch Installation - 2014 Nissan Titan - Hidden Hitch

Today on our 2014 Nissan Titan, we'll be installing Hidden Hitch, 2-inch-receiver 2-hitch, part number 70530. This is what our hitch will look like, once its installed. Next, we'll go ahead and give you a couple measurements, to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3 inches. From the top of the receiver tube to the ground is 21-1/2 inches. This will assist your selecting accessories such as a ball mount, bike rack, or cargo carrier.



Curt Relay Kit Installation - 2014 Nissan Titan

Today on a 2014 Nissan Titan, we'll be installing the Pollak 7-pole vehicle end connector, part number PK11893 in conjunction with our Curt Relay Kit, part number C57000. Now to begin our install, we'll first locate the vehicle's 7-pole connector. This will be above the bumper on the driver's side. We'll go ahead and cut the tape that goes around it, holding the 7-pole connector end to the wiring harness. We'll pull it out to where we can gain access to it. Then we'll remove the 7-pole connector end weather cap. To remove the cap, we'll press on the connector lock and then pull the cap out. We'll need to install our 7-pole mounting bracket. We'll be using our Pollak 7-pole mounting bracket for vehicle ends, part number PK12711U using the Pollak install hardware kit, part number PK11926. We'll take the 7-pole bracket and secure it correctly to the hitch mounter bracket with the bolt down through the hitch mounter bracket into the 7-pole bracket and then secure it with a nut underneath. We'll have two fasteners that secure it to the hitch mounter bracket. Next, we'll take our 7-pole connector and secure it to the 7-pole bracket. Now we can take our wiring harness that we prepared and plug it into the back of the 7-pole connector.



Hopkins Smart Hitch Backup Camera Installation - 2010 Nissan Titan

Today on our 2010 Nissan Titan we'll be installing the Hopkins Smart Hitch Backup Camera and Hitch Aligner System, part number HM50002. This backup camera makes driving in reverse and hooking up a trailer simple by giving you a full crystal-clear image of what's behind you. The color monitor gives you visual cues and audible alerts to help you back up safely. The camera also switches from hitch mode to everyday mode with the push of a button. Now we'll show you how the camera works. We'll go ahead and shift the vehicle into reverse while our foot's on the brake. As soon as the vehicle is put in reverse the monitor comes on and you get a view behind the vehicle.





Nissan Titan Questions

  • The first thing I would check is the trailer wiring running light fuse located in the power distribution box under the hood. Once the fuse box is located check the legend on the lid to determine the correct fuse to check. Blown running light fuses are a common problem with the Nissan Titan trucks. If the running light fuse is not blown or missing, you should also check fuses in the cab of the truck. Again use the legend on the cover, you will have a fuse box on the passengers...
    view full answer...

  • First, lets start with master cylinder replacement. The recommendation you got for replacing the complete actuator, is most likely a good idea because there is a reason for the crud and such that you are finding in the master cylinder and replacing the master cylinder itself is a pretty involved undertaking. We have a video showing a master cylinder replacement that should be helpful, if you decide to go this route. Other reasons for replacing the whole actuator would be that...
    view full answer...

  • Boat Trailer Roller Bunks, like the item you selected, part # DL21741, are not designed to line-up or center the boat, but for the boat to rest and roll on the bunks. Typically, if you are loading a boat the boat is not loading squarely it is because the trailer is too deep in the water. You would want to use part of the trailer as a reference to determine how far to back the trailer into the water. You would want to install the bunks in place of your existing bunks or rollers....
    view full answer...

  • The first thing I would check is the trailer wiring running light fuses located in the power distribution box under the hood, they should be fuse number 32 and 36. Once the fuse box is located check the legend on the lid to verify the correct fuses to check. Blown running light fuses are a common problem with the Nissan Titan trucks, and if the fuse is blown you need to make sure your trailer wiring is not shorted before plugging it in again or you will continue to blow fuses. Next,...
    view full answer...

  • The # N40975 Trailer Wiring Kit will include detailed instructions on how to install this part and the associated relays. There is a relay panel under the hood, in the engine bay, by the battery on the passenger side. If you remove the cover you will see some open ports. Trailer Tow 1 is where the blue relay goes and Trailer Tow 2 is where the brown relay goes. I have included a video showing the installation of this harness below. Most likely, your current harness is missing...
    view full answer...

  • I have attached a brake controller installation video on a Nissan Titan for you to check out. It shows exactly where the brake controller harness will be located under the dash. The truck in the video is a 2008 model, but it will be the same for your 2012 model. I have also attached a photo of the under side of the dash that shows where the harness will be located. The harness will be located underneath and left of the steering column, taped to another harness near the emergency...
    view full answer...

  • In my opinion the Swagman Platform-Style 2 Bike Carrier for RV Bumpers, # S64663, is the best rack for use on a 4 inch continuously welded steel RV bumper. This rack folds compactly for storage, will also work in a standard 2 inch hitch on a vehicle, and comes with the bolt on receiver for the RV bumper. This style of rack is super easy to load the bikes on and secures the bikes very well, keeping them from contacting each other or the back of the trailer causing damage. If...
    view full answer...

  • The first thing I would check is the trailer wiring running light fuse located in the power distribution box under the hood. Once the fuse box is located check the legend on the lid to determine the correct fuse to check. Blown running light fuses are a common problem with the Nissan Titan trucks. If the running light fuse is not blown or missing, you should also check fuses in the cab of the truck. Again use the legend on the cover, you will have a fuse box on the passengers...
    view full answer...

  • If the second wire is white it most likely is a ground wire and would just need to be run to a clean, metal surface. However, in some situations the light will ground through the mounting bolts of the light assembly. So if the light assembly is a stop/turn and tail assembly and there are only two wires the assembly grounds through the mounting hardware and the two wires are for the stop/turn and tail light circuits. If the light assembly only has a single intensity bulb...
    view full answer...

  • I do not recommend using air bags and weight distribution at the same time. If you are experiencing rear end sag on the tow vehicle caused by towing a trailer then the best solution is weight distribution. But not just any weight distribution system. It has to be the proper capacity. To choose a weight distribution system you will need to go by the total tongue weight of the set up. This is calculated by taking the tongue weight of the trailer, when loaded and ready to tow,...
    view full answer...

  • We carry a broad range of Ventline products, complete vent assemblies as well as individual replacement parts, for both of the part numbers you referenced. For Ventline item V2092 we offer complete vent assemblies, # V2092SP-29 in smoke color and # V2092SP-28 in white. Replacement domes are also available, # BVD0449-A03 in smoke and # BVD0449-A01 in white. For powered vent V2094 we offer a complete vent assembly # V2094SP-34 in smoke and # V2094SP-30 in white. Replacement...
    view full answer...

  • If you have a 2007 Nissan Titan or Frontier and the truck has a factory installed 7-Way trailer connector all you will need is the brake controller and vehicle specific wiring harness. I recommend going with a proportional brake controller that engages the trailer brakes in proportion to how much the truck is breaking. This will reduce wear and tear on the truck and trailer and make for safer braking situations. For a proportional controller with wiring harness, I recommend...
    view full answer...

  • The relays in the Hopkins 7-Way and 4-Way Connector, part # N40975, are the relays you will need to activate the towing circuits on your 2008 Nissan Titan. Hopkins doesn't sell the relays separately, but luckily enough Curt Manufacturing does. You can get the relays minus the trailer connector by ordering part # C57000.
    view full answer...

  • It sounds like you are looking for are the tow package relays for your 2013 Nissan Titan. If that is the case, then you will want the Curt Relay Kit, # C57000. These relays are required if your truck does not have 12v power or turn signals at the 7-way trailer connector. These relays fit into the under-hood fuse box and are for the turn signals and 12v power. I have attached a video showing how to install these relays. Some trucks will require a third relay, part # 38666-1,...
    view full answer...

  • As you probably know there are only certain bike racks that are rated for use at the back of an RV or trailer. I have included a link to the ones that carry 4 bikes for you. If the bumper is 4 inches square you can use the Swagman rack # S80600 which you can position around the spare tire if you want. I have linked a video review of this rack for you. If your Jayco trailer has a 2 inch trailer hitch at the back then I recommend the Swagman Trailhead # S63381. This is a...
    view full answer...

  • This does sound like a bad or missing relay. You can test the 7-Way connector without the trailer attached to see if you get any signal at all on the turn signal/brake light circuit. If you do get a signal but the lights are not working on the trailer, it could be that the extra load from the trailer lights is not allowing them to function properly. No signal would indicate a problem further up, most likely a blown fuse or relay. The 2004 Nissan Titan should only need 2 relays...
    view full answer...

  • I spoke with my contact at Redline and he informed that the threads on all 1/2 inch wheel studs should be the exact same, and that there is not a course or fine thread axle stud. When I described to him that problem you are having he said that you might have metric sized threads on your pop-up camper and that is why the lugs you bought did not thread on. I would take one of the lugs that you know will thread onto your studs and go to a hardware store and try threading the...
    view full answer...

  • The Derale Series 8000 Plate-Fin Transmission Cooler Kit, item # D13503, will provide extra cooling to help keep your transmission at normal temperatures when towing. Whether or not any cooler will provide enough cooling depends on many factors specifically related to your vehicle and trailer setup. I did a bit of checking on the 2006 Nissan Titan towing capacities and found that the 2006 Titan is rated for somewhere between 9,200 lbs and 9,500 lbs Gross trailer weight, properly...
    view full answer...

  • It sounds like the trailer wiring running light fuse may be blown. This fuse is located in a power distribution box under the hood at the rear of the drivers side of the 2010 Nissan Titan. Once the fuse box is located check the legend on the lid to determine the correct fuse to check. If this does not solve the issue, let me know, I will be glad to look into the issue further.
    view full answer...

  • We do separately offer only the relays for Nissan vehicles that come as part of the kit you referenced, part # N40975. The three relays by themselves are available as part # C57000. I have linked a video showing installation of these relays in a 2011 Titan. These install in the relay box behind the battery; the underside of the box cover should have labels for each relay socket. If these relays are missing or damaged then this kit should take care of the issue. You might also...
    view full answer...




Articles you may be interested in








Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email






etrailer.com reviews etrailer.com reviews

All images, layout and content copyright etrailer.com