Nissan Rogue owners are most interested in these products
change vehicle
Trailer Wiring Harness Installation - 2010 Nissan Rogue
Today on this 2010 Nissan Rouge, were going to install part number 118480 from Tow Ready.First thing we need to do is go ahead and open up the hatch and remove the floor panels. The trays that surround the spare tire well have to unbolt from the floor too. Well also remove the threshold. Well also pull back the weather strip around the door to make things a little easier to get to pry apart the pieces. Well also remove the anchor points that are in the side panels.Once weve got all the pieces away from the vehicle, well go ahead and start installing our wiring. Well begin with the drivers side and point out where the connection point is.
Trailer Hitch Installation - 2010 Nissan Rogue - Curt
Today on this 2010 Nissan Rouge, were going to install part number C12247 from Curt.This is what the hitch looks like when its installed on a vehicle. Next well give you some measurements to help you out in selecting some accessories such as a bicycle rack or a cargo carrier. From top of receiver opening down to the ground is going to be 14 and a quarter inches. From center of the hitch pin hole to outer edge of the bumper is going to be about 7 and a quarter inches. Now well go ahead and show you how the hitch is installed.First thing were going to do is go over to the passenger side frame rail and remove the tie down bracket. The two bolts in the bottom and two bolts on the side.
Trailer Hitch Installation - 2010 Nissan Rogue - Hidden Hitch
Today on this 2010 Nissan Rogue were going to install part number 87457 from Hidden Hitch. This is what the hitch looks like when its installed on the vehicle. Next, well give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 14 inches. And, from the center of the hitch pin hole to the edge of the bumper will be about 7 inches. Now, well go ahead and show you how the hitch is installed.
Trailer Hitch Installation - 2010 Nissan Rogue - Draw-Tite
Today on this 2010 Nissan Rogue were going to install part number 75606 from Draw-tite. This is what the hitch looks like when its installed on the vehicle. Next, well give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 14 inches. And, from the center of the hitch pin hole to the edge of the bumper will be about 7 inches. Now, well go ahead and show you how the hitch is installed.
Trailer Hitch Installation - 2010 Nissan Rogue - Curt
Today on this 2010 Nissan Rogue were going to install part number 13185 from Curt. This is what the hitch looks like when its installed on the vehicle. Next, well give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 14 inches. And, from the center of the hitch pin hole to the edge of the bumper will be about 7 inches. Now, well go ahead and show you how the hitch is installed.
Husky Cargo Floor Liner Review - 2011 Nissan Rogue
Today, we'll be test fitting the Husky Floor Liner in the rear cargo area, part number HL26701, black in color for your 2011 Nissan Rogue. This application is also available in gray, part number HL26702. First, we'll go ahead and remove the older manufacturer's floor mat, and now we're ready to install the Husky Cargo Liner. Husky Liner is custom mold to precisely the vehicle and stay in place. The shape, channels and moldings all work to keep dirt and debris contained in the liner and off of the carpeting. As you can see, the raised outer edge is perfect for protecting the carpeting.
Trailer Hitch Installation - 2011 Nissan Rogue - Curt
Today on our 2011 Nissan Rogue, we'll be installing the Curt Hitch, part number 12247. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch such as a bike rack or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 7 inches. From the top of the receiver tube to the ground is 10-1/4 inches. Now, let's go ahead with the installation.
Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2011 Nissan Rogue
Today on our 2011 Nissan Rogue, well be test fitting part number S64670 This is a Swagman XTC-2, two-bike carrier for both 1-1/4 and 2 inch hitches. Now to begin our test fit, weve already gone ahead and remove the 2 inch adapter. Well go ahead and slide the bike rack shank into the hitch, line up the hitch pinhole and install and tighten down our anti-rattle bolt. With the bolt tight, our bike rack is secured to the vehicle. Well now go ahead and give you a few measurements. Our ground clearance at the bike rack is 16 inches and from the closest point of the bike rack to the back of the vehicle is 1 inch.
Pro Series Q-Slot Hitch Bike Rack Review - 2011 Nissan Rogue
Today on our 2011 Nissan Rogue, well be test fitting the Pro Series Q-Slot Platform-Style Bike Carrier, part number PS63134. Now to begin our test fit, well slide our bike rack shank into the hitch, line up the hitch pinhole, and install our hitch pin. Well then put the safety clip on the other side which will secure our bike rack to the vehicle. Now, well go ahead and give you a few measurements. Our ground clearance at the bike rack is 17 inches and from the closest point of the bike rack to the back of the vehicle is 4 inches. We can now go ahead and unfold the bike rack platform and open our cargo door.
Trailer Hitch Installation - 2011 Nissan Rogue
Today we are working on a 2011 Nissan Rogue. We are going to be installing a DrawTite hitch part number 75606. This will also be comparable to Hidden Hitch part number 87457. Here are a couple of measurements that will assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost point of the bumper is 4-1/2 and from the top of the receiver tube to the ground is 13-1/4. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier.
Rhino Rack Roof Rack Installation - 2011 Nissan Rogue
Today on this 2011 Nissan Rogue we are going to be installing a Rhino Rack SXB roof rack system with Aero crossbars. After we have assembled the crossbars, we can begin mounting them on our vehicle. First, we will take the front crossbar and loosely place it into position. First we will make sure that the crossbar is overhanging the same amount on both the driver side and passenger side. And then we will position it so that it is running perfectly perpendicular to the vehicle. Once we have the first crossbar in position, we can begin tightening it down. As we tighten this Allen head bolt, not only will the clamp begin to grab on to our side rails but it will also tighten the crossbars to the clamps. We will move back and forth from the driver side to the passenger side to tighten down the rack evenly. Once we have our front crossbar installed, we can go ahead and install our locking end caps. The locking end caps not only help us seal the end of our crossbars. But because they are locking, they also protect our rack from being stolen. 1:03
Thule Crossroad Roof Rack Installation - 2011 Nissan Rogue
Today on this 2011 Nissan Rogue we are going to show you how to install a Thule Crossroad roof rack system. The Thule Crossroad system is designed to attach to vehicles with factory raised side rails like we have on our Rogue. Once we have the crossbars assembled, we can place them on top of our side rails. Make sure that they are spaced evenly on both sides with the side rails so that the crossbars run perpendicular to your vehicle. Once you have the front crossbar in place, you can use the integrated tool on the end cap to tighten them down. The Crossroad feet attach to the factory side rails using a rubber coated steel band. This band will strongly and securely grip your side rails but the rubber coating will help protect them as well. As we tighten down the clamp on the Crossroad foot, it also tightens the crossbar into the foot. We will move back and forth from the driver side to the passenger side to make sure the rack tightens down evenly and we do not lose our positioning. 0:57
Trailer Wiring Harness Installation - 2009 Nissan Rogue
Today we are going to be installing wiring harness part number 118480 on a 2009 Nissan Rogue. We have opened up the rear hatch of the vehicle and we are going to go ahead and point out where we need to locate the connection points for our wiring harness. The connection points are actually located behind the tail light assemblies, on the inside of the vehicle, behind these panels, on both sides of the vehicle. To gain access to those, we are going to need to remove quite a few items here from the rear end of the vehicle. To release these screws here, you actually want to align the arrows. There is an arrow here on the inboard side, along with the arrow on the knob. If you align those two, it will allow these two clips to release. There are also three screws here that are holding this compartment in that we are going to need to remove as well.
Trailer Hitch Installation - 2009 Nissan Rogue
Today on this 2009 Nissan Rogue, we will be installing Hidden Hitch part number 87457. This installation will also apply to the Draw-Tite part number 75606. Looking underneath the vehicle at the driver side frame rail, you can see here that there are three existing weld nuts in the bottom of the frame. Into these weld nuts we will be using the 12 mm bolts along with the conical tooth washers. That setup will be the same over here on the passenger side. But you will note that we have, not only an existing tow hook that is taking up the first two holes at the rear of the frame, but we also have an existing bolt here at the forward side as well. So the tow hook which consists of two bolts here at the bottom of the frame and two bolts on the side of the frame will need to be removed before we can get started. And then we will also want to remove the bolt at the more forward side as well.
Nissan Rogue Questions and Answers
- Will the Thule T2 Platform Bike Rack # TH916XTR Fit on a 2012 Nissan Rogue
- You can use the Thule T2 Platform Bike Rack, # TH916XTR, on your 2012 Nissan Rogue as long as you have a 2 inch trailer hitch. There are a few things to consider when choosing a platform style bike rack for your vehicle. First, you will want to make sure that you can mount your bikes on the bike rack without the bikes hitting your bumper. The T2 rack measures 19 inches from the center of the hitch pin hole to the closest bike carrier rail, so this should not be an issue.
The other factor to
view full answer...
- Bumper Clearance for the Kuat NV Bike Rack # N101-103 on a 2011 Nissan Rogue
- I do have some information that will give you an idea of how much clearance you will have between the Kuat NV Bike Rack, # N101-103, and your 2011 Nissan Rogue, however, I do not currently have a Rogue on my lot to make a test fit video. As soon as we have a Rogue available for test fits, we will post a video.
What I can tell you is that the NV bike rack measures 7-3/8 inches from the center of the hitch pin hole to the closest part of the bike rack. When we installed a trailer hitch on a 20
view full answer...
- Trailer Hitch & 4 Bike Hitch Mounted Tilting Rack for 2008 Nissan Rogue
- Since you will be using a bike carrier to transport 4 adult bikes, I recommend that you opt for a Class III hitch receiver as this will offer a higher tongue weight (TW) rating of 350 pounds and best handle the vertical load from your 4-bike carrier.
The product page link provided will show you all three options for 2-inch Class III hitch receivers. A good cost-effective choice is the Hidden Hitch # 87457 which installs without welding or drilling and includes all required installation hardwa
view full answer...
- Trailer Hitch Option for a 2010 Nissan Rogue and the Kuat NV Bike Rack # NV101-103
- It is possible to carry the Kuat NV Bike Rack, # N101-103, with the Curt Trailer Hitch, # 13185, on your 2010 Nissan Rogue, but it is going to be a close fit. We have installed the Curt Trailer Hitch, # 13185, on a 2010 Nissan Rogue and found that the distance from the center of the hitch pin hole to the edge of the rear bumper is 7-1/2 inches.
In the folded up position, with the hook arms folded out, the distance from the center of the hitch pin hole to the closes part of the NV bike rack i
view full answer...
- Attaching the Power Wire for a Trailer Wiring Harness on a 2013 Nissan Rogue
- On trailer wiring harness # 118480 for your 2013 Nissan Rogue, you will have to connect the power wire from the converter directly to the vehicle battery. No other 12 volt source should be used.
It is not recommended to attach the power wire from the converter to any other 12 volt power source other than directly to the
battery. The reasons for this are: connecting to a circuit like that 12VDC outlet defeats the purpose of isolating the trailer wiring from the vehicle wiring so short circui
view full answer...
- Recommended 2 Bike Hitch Mounted Bike Rack for 2013 Nissan Rouge
- To see the various 2 bike racks that are compatible with the 2 inch receiver on your Rouge, click the provided link.
The Swagman Trailhead, part # S63360 is a good lower-cost rack that has what I consider to be essential features like anti-sway cradles that prevent the bikes from swinging back and forth during transport and sturdy rubber straps that hold the bikes to the rack. An optional locking anti-rattle hitch pin and cable lock, part # S64031 is also available.
The Thule Helium, part
view full answer...
- Troubleshooting Exhaust Hanger Interference for Installing Curt Hitch on a 2010 Nissan Rogue
- There should not be any interference with the exhaust brackets to install the Curt Hitch # 13185 on your 2010 Nissan Rogue. If you check out the picture I attached you will see how it should bolt up in relation to the exhaust hanger brackets.
Since there are several possible holes on your vehicle that you could be trying to install the mounting hardware of the hitch onto, my first thought is that maybe you are not using the correct holes.
I attached installation instructions and an install
view full answer...
- Will the Thule Ascent 1600 Cargo Box Clear the Antenna on a 2012 Nissan Rogue
- I checked with Thule and the Ascent 1600, # TH604, will fit your 2012 Nissan Rogue with factory roof rack and not cause any interference with the rear hatch. I did some research on the antenna and based on what I found the box should not interfere with the antenna either. The crossbars that run side to side are high enough that when the box is mounted on them it will be about the antenna.
view full answer...
- Will the Thule Raceway 2 Bike Rack Fit on a 2012 Nisan Rogue SL AWD
- The Thule Raceway 2 Bike Rack, # TH9001, is listed as a fit for your vehicle as long as it does not have a rear spoiler. If your vehicle has a rear spoiler, then I would strongly recommend looking into a roof mounted or hitch mounted bike rack. The spoiler that comes with the Nissan Rogue was not designed to support a load and could deform or even break under the weight of a bike rack and bikes.
To carry your Specialized Hard Tail 29er, I would recommend picking up the Thule Bike Adapter Bar
view full answer...
- What Roof Rack for 2013 Nissan Rogue With Naked Roof
- Roof rails on your 2013 Rogue are a factory-only option. We cannot offer these rails themselves on an aftermarket basis.
However, we can offer you several options for roof racks that can be fitted to a 2013 Nissan Rogue with a naked roof (meaning a roof with no factory-installed side rails or crossbars).
Differences between products suitable for your Rogue will include shape, length and color of the crossbars, weight capacity of the rack system, and how quiet the rack is during highway dri
view full answer...
- Will Sport Rack Frontier Semi-Custom Roof Rack, Part # A21010S, fit a 2009 Nissan Rogue S
- After speaking with my contacts at SportRack, the # A21010S is not recommended for the Nissan Rogue.
We suggest one of the following combination of items for your vehicle with a naked roof:
The most economical option is the Rhino-Rack 2500 Series Roof Rack, parts # DS126B and # DK146.
The quietest option is the Thule AeroBlade, parts # THARB53, # TH480R, # THKIT1587. Please see attached video for this option.
The above recommendations are for the 2009 Nissan Rogue with naked roof (no
view full answer...
- Availability of Wiring Harness For 2013 Nissan Murano
- The Tow Daddy Universal Wiring Kit, part # TD10000S, you have referenced is a universal design wiring harness for vehicles being flat towed. It is not a custom fit application.
The Nissan Rogue is a vehicle that uses a Continuously Variable Transmission (CVT) and will not be able to be flat towed. The front wheel drive vehicle would have to be towed with a tow dolly and the all wheel drive version would need to use a trailer.
If you are going to be towing a trailer with your 2013 Nissan R
view full answer...
- Recommendation For Bike Rack on 2012 Nissan Rogue With a Rear Spoiler
- To carry bikes on your 2012 Nissan Rogue you will need to use a hitch bike rack. A hitch bike rack will install on a hitch on your vehicle and allow you to carry your bikes without any interference with the rear spoiler. I do not have a trunk bike rack that will fit on your vehicle if it has a rear spoiler. The bike rack and/or the cables that attach a trunk bike rack to the vehicle would contact the spoiler which cannot withstand the stress.
The hitch I would recommend is the Hidden Hitch Cl
view full answer...
- Will the Thule Passage 2 Trunk mount Bike Rack Fit a 2010 Nissan Rogue
- Yes, the Thule Passage 2 bike rack, # TH910XT, will fit your 2010 Nissan Rogue. The rack comes with everything needed for installation. I have included a link to the instructions and a link to a video review of this rack for you.
Some bikes like womens, childrens, or any alternative frame bike, may need the adapter bar, # TH982XT, in order to load them on the rack and for greater ground clearance because the adapter allows those bikes to set level on the rack. I have included a link to a vide
view full answer...
- Will the Thule Passage 2 Trunk Mount Bike Rack Fit a 2012 Nissan Rogue
- Thule does list the Passage 2 bike rack, # TH901XT as a fit for the 2012 Nissan Rogue. However, if the vehicle has a rear spoiler then it is considered a no-fit. I have included some links on the Passage bike rack for you to view.
If you do have a rear spoiler you can still carry bikes using a trailer hitch, like # 87457, and a trailer hitch mount bike rack. For a 2 bike rack, one of our most popular options is the Swagman XTC-2, # S64670. This is a platform style rack that holds 2 bikes. I h
view full answer...
- Trailer Hitch and Bike Compatibility with a 2012 Nissan Rogue
- Hidden Hitch and Draw-Tite are sister companies. The Hidden Hitch # 87457 and Draw-Tite # 75606 are essentially identical. The design, appearance, build quality, finish, install method and weight capacities are identical. Both hitch crossbars are constructed of square-tube steel.
The installation instructions and video that I have attached will apply to both hitches on your 2012 Nissan Rogue. I would recommend going with the Hidden Hitch Trailer Hitch, # 87457, because it will be more cost ef
view full answer...
- Will a Trunk Mounted Bike Rack Fit a 2011 Nissan Rogue or Mazda 6 Both with Rear Spoilers
- The Thule Raceway, # TH9001, will not fit on a 2011 Nissan Rogue with a rear spoiler. The bike rack and/or the cables that attach it to the vehicle would contact the spoiler which cannot withstand the stress. For the Rogue, I recommend going with a trailer hitch and a hitch mounted bike rack.
For a trailer hitch, you can use # 87457. And for a bike rack, the most popular 2 bike model is the Swagman XTC-2, # S64670. I have included informational links on the hitch and bike rack for you.
For
view full answer...
- Will the Swagman Roof Mount Bike Rack Fit a 2009 Nissan Rogue with factory Crossbars
- You will have to measure the width of your factory crossbars to determine if the Swagman roof bike rack, # S64710, will fit. The rack will fit on bars that are no wider than 3-3/8 inches but a 3 inch width is ideal. And they can be installed on cross bars that are up to 52 inches apart measured from the center of one bar to the other bar center. I have included a link to the installation instructions and a link to a video review of the bike rack for you.
I also checked with Thule and Yakima a
view full answer...
- Thule Raceway Trunk Mount 3 Bike Rack Fit on a 2011 Nissan Rogue
- The Thule Raceway 3 Bike Rack, # TH9002, will fit on your 2011 Nissan Rogue as long as you do not have a rear spoiler. Thule says the clips must be placed in the gap at the front edge of the top of the hatch door and the lower clips should be placed at the bottom edge of the door. The rear wiper should not be used when the carrier is mounted.
If you do have a rear spoiler, then there are no trunk mounted bike racks available for your vehicle because the rear spoiler cannot support the weight
view full answer...
- Trunk Mounted Bike Rack Compatibility for a 2008 Nissan Rogue
- The Thule Raceway 2 Bike Carrier, # TH9001, will fit on your 2008 Nissan Rogue as long as you do not have a rear spoiler. The clips will need to be placed in the gap at the top edge and at the bottom of the rear hatch. The lower arm of the carrier should be positioned on the upper tier of the bumper.
A spoiler will not be able to support the weight of the bike carrier and could be damaged. In this case I would recommend a hitch like the Hidden Hitch Class III hitch, # 87457, and a hitch mount
view full answer...
- Will the Yakima QuickBack Trunk Mount Bike Rack Fit a Nissan Rogue
- The Yakima Quickback bike rack, # Y02621, will fit a 2008 to 2010 Nissan Rogue but not 2011 and newer models. I have included a link to the installation instructions and a link to a video review of this bike rack. If you will be carrying womens, childrens, or alternative frame bikes, I recommend using the Tube Top, # Y02531 to carry the bikes more level. I have included a link to a video that shows how the adapter works.
view full answer...
- Bike Rack Options For a 2008 Nissan Rogue With a Factory Rear Spoiler
- All of the truck mounted bike racks for your 2008 Nissan Rogue require straps to be secured to the top and bottom of the tail gate. It is not recommended to mount the straps over the spoiler on your vehicle because the tension can damage the spoiler.
The best option will be a hitch like the Hidden Hitch, # 87457, and a hitch mounted bike rack. One of our most popular hitch mounted bike racks is the Rola TX-103, # 59403.
Adding a hitch to your vehicle will also give you the option to tow
view full answer...
- Can the KarPak Rooftop Cargo Bag be Installed on a 2011 Nissan Rouge Without Cross Bars
- Yes, you can attach the Highland KarPak Rooftop Cargo Carrier Bag, # 1039800, to the roof of your 2011 Nissan Rogue, with factory raised rails that run front to back on the roof. The bag has 6 compression straps and plastic clips designed for securing the bag.
You will need to make sure that the bag can be installed and secured in such a way that bag has minimal movement when accelerating and stopping, to avoid damage to the roof of your vehicle. I normally recommend the use of cross bars whe
view full answer...
- Trailer Hitch and Bike Rack Recommendations for a 2008 Nissan Rogue
- For a trailer hitch, the most popular option for the 2012 Nissan Rogue is Hidden Hitch trailer hitch # 87457. This is a Class III trailer hitch with a 2 inch receiver. I have included a link to the installation details and a link to a video that shows a typical installation for you.
In the video, it is a 2011 model, but installation will be very similar on your 2012 model. We measured the clearance from hitch pin hole center to the edge of he rear bumper at 4-1/2 inches. This is an important
view full answer...
- Will the Thule Snowcat Ski and Snowboard Carrier Fit a 2011 Nissan Rogue with Factory Side Rails
- I checked with Thule and the Snowcat, # TH5401, is listed as a fit for a 2011 Nissan Rogue with factory side rails that run front to back. I have included a link to the installation details and a link to a video review for you.
view full answer...
- Availability of Glacier Tire Cable Chains For 2009 Nissan Rogue
- You will need the Glacier Tire Cable Chains, part # PW1038, to fit either the 215/70R16 tire size or the 225/60R17 tire size on your 2009 Nissan Rogue. These cable chains are a SAE Class S tire chains which are designed for vehicles with limited wheel-well clearance. I would also recommend to use the Glacier Rubber Adjusters, part # PW100, to keep tension on the snow cable chains.
You will need to check your owners manual or with the car dealer to determine if you can use snow tire chains on
view full answer...
- Will the Thule Raceway 2 Bike Rack Fit on a 2009 Nissan Murano and a 2011 Nissan Rogue
- The Thule Raceway bike rack, # TH9001, would make a great choice for both of your vehicles as long as neither vehicle has a rear mounted spoiler.
I recently had the chance to install this rack on a vehicle and it is the easiest trunk mount bike rack I have installed and removed. For this reason, this is the rack I personally would choose for a trunk mount rack.
view full answer...
- Yakima Bighorn and Adapter Bar Recommendations for Carrying Womens Beach Cruiser Bikes
- In order to determine if a bike rack will have enough clearance to work on your 2010 Nissan Rogue you will need to take one important measurement. You will need to measure from the center of the hitch pin on the hitch of your vehicle out to the furthest point out on your bumper.
The Yakima BigHorn Bike Rack # Y02405 would be a good choice for you if you have a hitch on your vehicle that has a 1-1/4 inch opening. This hitch measures 11-5/8 inches from the center of the hitch pin out to the nea
view full answer...
- Will the SportRack Aero Cargo Box Fit a 2010 Nissan Rogue with Factory Roof Rack
- What you will have to do to determine fit is measure the width of the crossbars on your 2010 Nissan Rogue. if they are less than 4 inches wide and they have a spread of 24 to 34 inches apart on center, then the SportRack Aero Cargo Box, # A90275, will fit.
There are other cargo boxes listed as a direct fit to the Nissan factory crossbars. For 18 cubic feet, you can use the Thule Atlantis, # TH687BXT, or the Thule Boxter, # TH611.
view full answer...
- How to Replace Thule Locking Cylinders on a Roof Rack
- When you go to change the lock cylinders on your roof rack to the cylinders of the Thule Locking Cylinders 4 Pack # TH544 you will insert the included universal change key into an unlocked cylinder that is currently in your roof rack and then remove the cylinder. It may take a little bit of wiggling for the cylinder to work itself loose, but when the change key is inserted into the lock cylinder the cylinder will be free to slide out.
Next, you will insert the change key into a cylinder from
view full answer...
all Nissan Rogue questions
