Select Your Vehicle
view cartView Cart

CALL NOW - 800-298-8924

Product Experts Available Now!

Free Shipping on Orders Over $99

Only 16 Hours 54 Minutes Remaining



Nissan Murano owners are most interested in these products

change vehicle






Nissan Murano Videos

Trailer Wiring Harness Installation - 2014 Nissan Murano

Today on our 2014 Nissan Murano, we'll be installing the Tow Ready T-One vehicle wiring harness with 4-pole flat trailer 00:00:06 connector. Part number 118481. To begin our install, we'll first open up the hatch as we'll need to remove some of the interior paneling to gain access to the manufacturer's wiring behind the tail light. We'll first need to remove the center spare tire cover as lifting it up and out of the way is just not adequate enough to get the rear storage compartment out. To remove it, we'll need to remove the cover over the rear cargo hooks. Using a small flat-blade screwdriver, we can pop the cap up and then remove the fastener.



Rain-X Weatherbeater Wiper Blades Installation - 2013 Nissan Murano

Today on our 2013 Nissan Murano we'll be installing the Rain-X wiper blades, part number RX30226 for the driver side and part number RX30216 for the passenger side. We'll remove our old blades by lifting up on the tab that secure them to the J hook and then pulling down. With our old blades removed, the new rain-X wiper blades slide right into place. We'll go and repeat this process on the passenger side. Thats all there is in installing the Rain-X wiper blades, part number RX30226 for the driver side and RX30216 for the passenger side on our 2013 Nissan Murano. .



Thule Helium Aero Hitch Bike Racks Review - 2007 nissan murano

Today on our 2007 Nissan Murano we're going to be test fitting the Thule Helium Aero 2-bike rack for 1 1/4 and 2 inch hitches, part number TH9042. We'll begin our test fit by inserting the shank into the hitch on our vehicle. This does have a self-locking hitch pin and we'll pull that out, insert that shank and that pin will go right into place. You'll then want to tighten down the anti-rattle device. Tightening this down is going to help remove any extra play in the shank of the rack, which is going to help to eliminate movement overall as you're going down the road. With that tightened down we'll get a couple of measurements. The closest part of the rack to the vehicle is going to be here at the back. That measures just 6 1/2 inches.



Trailer Wiring Harness Installation - 2012 Nissan Murano

Today on our 2012 Nissan Murano, we'll be installing the Tow ready T-One Connector, part number 118481. Next we'll go ahead and show you how to use your new 4-pole connector. We'll take our 4-pole and run it out and down to the center of the hitch or accessory. Be careful, stay away from the latch as pinching the wire off in the latch can harm it. However, the weather seal is thick enough that it won't when we simply close the rear cargo door on the wire. Then once we're finished using our new 4-pole wire we'll go ahead and open up the rear cargo door, roll it up and store it in the rear storage tray. To begin our installation, we'll first open up the rear cargo door.



Thule Hitching Post Pro Hitch Bike Racks Review - 2007 Nissan Murano

Today on our 2007 Nissan Murano, we are going to be test fitting the Thule Hitching Post Pro 4 bike rack for inch and a quarter and two inch hitches part number TH934XTR. We'll begin our test fit by inserting the shank into the hitch of the Murano. You want to watch for the hitch pin holes to line up. With those in line, we can take the included threaded anti rattle hitch bolt and thread that into place. Sometimes you might have to set the rack around a little bit to get it in the spot we're it doesn't line the bolt up. We'll get that hand tight and then we'll finish it off with our wrench.



Trailer Hitch Installation - 2014 Nissan Murano - Hidden Hitch

Today on our 2014 Nissan Murano, we're going to be installing the Hidden Hitch Trailer Hitch Receiver, part number 87486. Now, here's what our hitch looks like installed on our vehicle. Now, we'll go ahead and give you a couple measurements in helping you choose some accessories for your hitch such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper, we have about 5-1/2 inches. From the top of the opening in the receiver to the ground, we have about 15-1/2 inches. Now let's go ahead and install our hitch. Now, we're going to begin our installation by going underneath the vehicle and installing a safety strap underneath the rear exhaust here. Now with our safety strap in place, we're going to need to remove a total of four rubber exhaust hangers to allow our exhaust to be lowered down a little bit to give us some working room. Let's go ahead and point out the four rubber exhaust hangers.





Trailer Hitch Installation - 2014 Nissan Murano - Curt

Today on our 2014 Nissan Murano, we're going to be installing the Curt Trailer Hitch Receiver, part number 13577. Now here's what our hitch looks like on our vehicle. Now we'll go ahead and give you a couple of measurements in helping you choose some accessories for your hitch, such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the opening in the receiver to the ground we have approximately fifteen and a quarter inches. From the center of the hitch pinhole to the outermost edge of the bumper, we have approximately four and a half inches. Now let's go ahead and install our hitch. Now before we begin our installation, we're going to need install a safety strap up underneath the exhaust.



Trailer Hitch Installation - 2009 Nissan Murano - Hidden Hitch

Today on our 2009, Nissan Murano, we will be installing the Hidden Hitch, trailer hitch, part number 87486. I'll give you a couple of measurements to help you pick out accessories, like ball mounts, cargo carriers and bike racks. From the top of the receiver tube to the ground, there's about 12-3/4" and from the center of the hitch pinhole to the outer edge of the bumper, there's about 5-1/2". Now, let's go see how it's installed. To begin the installation, we'll start by removing the three exhaust hangars at the rear of the vehicle. Now, to remove the hangars, the first thing we need to do is spray them down with some spray lubricant. With those sprayed down, we can take a pry bar and pop the exhaust hangar out of place. Now, when the exhaust is loose, we have to remove this rear co-hook and to remove that, we have four bolts that we'll need to remove. Those two and these two bolts up here. Now that are things are out of the way, I'll go and inaudible 00:01:42 the attachment points for the hitch. This hole here, closer to the exhaust, there, the one in the back by the exhaust hangar. The mounting points from the passenger side are just a little bit different. We will have two on this vehicle. Well, this one in the front, nearest to the exhaust and this other well, not back 00:02:06 here by the exhaust hangar. Now, before mounting our hitch, we're going to go back to those mounting holes, spray some spray lubricant in there and clean the mount.





Thule XB16 Snow Tire Chains Review - 2013 Nissan Murano

Rate your transcript OrderClientKevin BrossRef #20624Order #TC0965042436 Today on our 2013 Nissan Murano, we'll be test fitting the Thule Standard Snow Tire Chains for SUV's, commercial vehicles and motor homes, part number TH01571255. Today we'll be fitting these chains on tire size 235/65-18. We're going to begin our test fit today by placing the chains flat on the floor, so that way we can un-kink and untangle our chains. We'll want to grab here on the yellow end, take it around back of our tire, bring it up on the inside, and latch the cable in place. Once we have the cable connected, we can then scoot it back a little, so that we can bring the rest of the chains over the top of the tire. We also want to make sure that these hooks are facing out, so that when we're in motion, we do not damage our tire. Now we'll move to the 6:00 position, where we'll bring the chain from the rear of the tire, feed it through our fastener, and then we need to pull it as tight as we can get it with our hands.



U-Ace 3D Classic Custom 2nd Row Floor Liner Review - 2009 Nissan Murano

Today on our 2009 Nissan Murano, we will be installing the U-Ace 3D Classic Custom Auto Floor Liner with MAXpider grip. Our liner is in beige and part number L1NS01822202. Also available in black, part number L1NS01822209, and available in gray, part number L1NS01822201. The first step is going to be to get our old floor liner out of place. We'll go ahead and set our new floor liners in place. As you can see, with the second row floor liner installed, it is specific to our vehicle. It comes up here, it does contour around our seat tracking.



U-Ace 3D Kagu Front Floor Liners Review - 2009 Nissan Murano

Today in our 2009 Nissan Murano we're going to be installing the U-Ace floor mats in beige, Part Number L1NS01811502. They're also available in black, Part Number L1NS01811509, and in gray, Part Number L1NS01811501. We'll start our install by removing the factory floor mat. With the factory mat out of the way, we can place our new U-Ace Kagu floor mat in. We'll do that for both the driver side and passenger side. Now, with the new mat in the car, you can see this is a vehicle-specific application. It lines up with our factory mounting points that is contour door vehicle, and it gives us additional coverage up under the pedals. Now we also have this textured material up on top of the mat to help keep you from sliding around. We also have the textured area where your foot will rest up by the pedals for a little additional grip.



U-Ace 3D Classic Front and Rear Floor Liners Review - 2009 Nissan Murano

Today on our 2009 Nissan Murano, we will be test fitting the U-Ace 3D Custom Auto Floor Liners with MAXpider Grip, part number L1NS01802202. Also available in black, part number L1NS01802209, and in gray, part number L1NS01802201. The first step is going to be to get our old floor liner out of place. Well go ahead and set our new floor liners in place. With the new floor liner in place, you can see its customized to fit this vehicle. It attaches to the factory mounting points and its custom contoured to our interior.



Husky Liners Classic Front Floor Liners Review - 2009 Nissan Murano

Today on our 2009 Nissan Murano, we will be installing the Husky Liners Classic Custom Auto Floor Liners, part number HL36571. To start off, we need to remove the factory floor liner, then we'll put our new Husky Liner in place. With the new mat in place, you can see we now have this raised containment walls that will help keep all the water, dirt and debris bring into the car in place and off your carpet and it is also contour to match the interior of your vehicle. This one is specific to this Nissan. If you look up under the dash, we also get a lot of added extra protection we didn't get with the floor mat. It goes up underneath our pedals especially over here on the left side. On the bottom of our Husky Liner mat, we have their patented stay put nibs which will help really dig into the carpet and keep our floor liner from moving around. Now over here on the passenger side of the vehicle, we got the floor mat in and just like on the driver side, we got a lot of added protection up towards the front and under the dash.



































Nissan Murano Questions and Answers


all Nissan Murano questions      








Stay Connected


Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email





Free Shipping on Orders Over $99

Only 16 Hours 54 Minutes Remaining


etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com