Select Your Vehicle
view cartView Cart
Only 13 Hours 31 Minutes Remaining

Nissan Frontier owners are most interested in these products

change vehicle






Nissan Frontier Videos

Trailer Wiring Harness Installation - 2000 Nissan Frontier

Today on this 2000 Nissan Frontier, we're going to install part number c55362 from Curt. First up we need to find our connection point for our key connector harness. We'll look underneath the passenger side. Along side the spare tire towards the back. Looks like our connection point right here. We need to push down on the small tab here to separate the connectors.



Trailer Hitch Installation - 2006 Nissan Frontier - Curt

Today on our 2006 Nissan Frontier, we'll be installing the Curt Trailer Hitch Receiver in a Class 3 with a 2" opening in the receiver, part number 13241. Here's what our hitch looks like installed on our vehicle. Now, we'll give you a couple of measurements in helping you choose some accessories for your hitch, such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is approximately 3 1/4". From the top of the opening in the receiver to the ground is approximately 18 1/2". Now, let's go ahead and install our hitch. First we'll go ahead and point out the mounting locations that we'll be using to secure our hitch to the vehicle. Before we can attach the hitch, we will need to clean out the existing weld nuts.



Trailer Wiring Harness Installation - 2011 Nissan Frontier

Today on our 2011 Nissan Frontier we'll be installing the Tow Ready Custom Fit Vehicle Wiring Harness with 4-pole flat connector, part number 118525. To begin our install we'll first need to go to the passenger side kick panel and remove the interior panel. To do this we'll need to remove the threshold first. To remove the threshold, we'll use a flat-blade screwdriver or interior trim panel tool to get underneath the threshold and pop the fasteners free. Next, we'll need to remove the kick panel. To remove the kick panel, we'll first remove the black cap nut. Then we'll release the fasteners underneath and set the kick panel aside.



Trailer Hitch Installation - 2011 Nissan Frontier - Curt

Today on our 2011 Nissan Frontier we'll be installing the Curt Class 3 2 Inch Receiver 2 Hitch, Part Number 13241. This is what our hitch will look like once installed. Next are going to be a couple of measurements to assist your selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3 1/2 inches. From the top of the receiver tube opening to the ground is 18 1/2 inches. This will assist your selecting accessories, such as a ball mount, bike rack, or cargo carrier.



Trailer Wiring Harness Installation - 2006 Nissan Frontier

Today in our 2006 Nissan Frontier, well be installing the Tow Ready T1 Vehicle Wiring Harness with 4-pole flat trailer connector Part Number 118525.Now well begin here at the rear of the vehicle. Here on the driver side at the rear of the vehicle, theres a factory plug that well be plugging our 4-flat into. Well need to first remove the blank cap thats already in the plug. To do this, well simply take a small flat-head screwdriver and push in on the locking tab and then pull the blank plug out. Once we have that done, well take our new plug that has the 4-flat connected to the other end and well simply plug it into it making sure that we hear the locking tab snap into place.Now that we have our plug in place, well go ahead and take the 4-flat end and route it up and over our hitch. Well then take the end dust cover and loop it through the safety chain hole and connect it back on to the 4-flat securing it to the hitch.







Thule XG12 Pro Tire Chains Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier Crew Cab, well be doing a test fit of the Thule Self Tensioning Snow Tire Chains, the XG12 Pro part number TH01594265. Tire sizes well be using today is 265/70/15. To begin with, we want to make sure that the tire chain is laid out flat, make sure that theres no kinks or knots in the chain. With the chain laid out, well go ahead and feed it behind the tire from the rear of the vehicle towards the front. Well want to make sure that we keep the yellow end of the blue cable towards the rear of the vehicle. With the blue cable and the chain fished behind the tire, well go ahead and bring the two ends of the blue cable up on top of the tire. With that, well go ahead and make the connection with the blue cable by slipping the end that has a yellow on it into the other end and latching the blue cable together.



Yakima DoubleDown Ace Hitch Bike Rack Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier well be test fitting the Yakima Doubledown Ace Four Bike Rack, part number Y02451. To begin our test fit well slide the shank of the bike rack into the receiver tube of the hitch, line up the pin hole and installed the attached pin. Here at the rear of the shank well tighten the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device.Now well go over some clearance measurements. We have about 14-1/2 inches of ground clearance. The closest point of the bike rack to the rear of our vehicle is about six inches. Weve added about 13 inches to the overall length of our Nissan Frontier. Well pull the pin with the red knob on the backside of our carrier and allow it to tilt away from the vehicle.



Yakima DoubleDown Ace 2 Bike Rack Review - 2013 Nissan Frontier

Today, on our 2013 Nissan Frontier, we'll be test-fitting the Yakima DoubleDown Ace 2-Bike Rack, part number Y02450. To begin our test-fit, we'll slide the shank of the bike rack into the receiver tube of the hitch, line up the pin hole, and install the attached pin. We'll tighten the hand-knob at the rear of the shank to engage our anti-rattle device, and secure our bike rack to our vehicle. Now, we'll go over a few clearance measurements. We have about fourteen and a half inches of ground clearance. The closest point of the bike rack to the rear of our Frontier is about six inches.



Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Nissan Frontier

Today, on our 2013 Nissan Frontier, we'll be test-fitting the Thule SUP Taxi Stand-Up Paddleboard Carrier, with a two-board capacity, part number TH810. With a Thule Rapid Traverse Roof Rack System assembled onto our vehicle, we'll begin our test-fit by placing the front part of the carrier onto our front bar. We'll then bring the rubber-coated steel straps around the underside of the front bar and hook them into the connection points. We'll then turn the gray knobs to bring the straps up around tightly against the bar. We'll then repeat the same process for the rear part of the carrier. With everything all tightened down and secured, we're ready to load up our board.



Thule Pulse XL Rooftop Cargo Box Review - 2013 Nissan Frontier

Today, on our 2013 Nissan Frontier, we'll be test-fitting the Thule Pulse XL Rooftop Cargo Box, with 16 cubic feet of space, matte black in color, part number TH615. With a Thule Rapid Traverse Roof Rack System assembled onto our vehicle, we'll begin our test-fit by placing the cargo box onto the vehicle's load bars. Now, since this box only opens from one side, you'll need to position it on the passenger's side of our vehicle. We can then unlock the box and open the lid, exposing the four slots in the bottom of the box. We can take the clamps, slide them down through the slots over-top of each bar, turning the knobs to tighten down the clamps. Quick tech tip.



Thule Helium Aero Hitch Bike Rack Review - 2013 Nissan Frontier

Speaker: Today, on our 2013 Nissan Frontier, well be test fitting the Thule Helium Aero two-bike carrier, part number TH9042. Well begin our test fit by sliding the shank of the bike rack into the opening of the hitch allowing the integrated hitch bin to fall into place, and then securing the bike rack to the vehicle by turning the black knob. This will engage the anti-rattle device, securing the Thule Helium to our Frontier. Well now go over a few clearance measurements to see how the two fit together. We have about 20 & inches of ground clearance. Weve added about 19 inches to the overall length of our Frontier. We can now pull the gray lever that at the top of the mast to swing the cradle arms out. With the cradle arms out, weve added about 29 inches to the overall length of our Frontier. To lower it on the tailgate and have access to the truck bed, we can pull the gray lever at the base of the bike rack and tilt the mast down.





Thule Roof Rack Fairing Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier, we'll be test screening the Thule Fairing for Thule Square Bar Roof Rack Systems, 44 inches in length, part number TH872XT. We'll place the fairing up onto the roof to establish the points in which the brackets need to go around the bar. We'll then place the black brackets around the underside of the front bar, making sure the arrow is facing towards the front of the vehicle. With all the brackets in place, we can then take the fairing and rotate it to get the clips to fit into place. Then we'll swing the clip around, snapping it onto the bracket, securing the fairing to the roof rack.We'll then repeat the same process for all three of the other brackets. Now that the clip's in place, we can then tighten down the black wing nuts to secure the fairing to the front bar.



Thule Big Mouth Roof Bike Rack Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Thule big-mouth roof-mounted bike rack, part number TH599XTR. With the Thule Rapid Traverse roof rack system already assembled onto our vehicle we'll begin our test fit by placing the bike rack up onto the vehicle's load bars. We'll then bring the front two brackets on the underside of the front bar and hook in the T-bolts into the designated slots. We'll then move to the rear, remove one wingnut to make the rear bracket go on top of the bar. We'll then move back up to the front making sure our T-bolts are still in position and turn the black wingnuts to secure the front part of the bike rack to the front bar. With everything all tightened down and secured we're ready to load up our bike. We'll undo the front and rear wheel strap and we'll undo the black lever which controls the jaws. We'll place our bike up onto the bike rack maneuvering the frame clamp up or on the sprocket and on the bottom portion of the frame. We'll then clamp down the black lever to secure the jaws to the bike frame. We'll then secure the front and rear tire with straps. And now that our bike is all loaded up that will complete today's test fit for the Thule big-mouth roof-mounted bike rack, part number TH599XTR, on our 2013 Nissan Frontier. .



Thule Apex 4 Hitch Bike Rack Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier, we'll be test fitting the Thule Apex, four bike rack, part number th9025. To being our test fit, we'll slide the shank of the carrier into the receiver tube of the hitch, line up the pin hole and install the attached pin. We'll tighten the hand knob at the rear of the shank to engage our anti-rattle device and secure our bike rack to our vehicle. Now, we'll go over a few clearance measurements. We have about 16 inches of ground clearance. The closest point of the carrier to the rear of our vehicle is about one inch. We've added about 12 1/2 inches to the overall length of our Frontier.





Diversi-Tech Adjustable Ball Mount Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier well be test fitting the Divirsi Tech self-locking adjustable aluminum ball mount part number DTALBM6600. Before I begin our test fit well first need to obtain the hitch height of our vehicle which is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after-market accessories. Well now begin our test fit by sliding the shank of the ball mount in the drop position into the opening of the hitch. We can then turn the key to allow the integrated hitch pin to fall into place securing the ball mount to the vehicles hitch. We can now remove the key and adjust the ball mount platform to its lowest position. Unlocking the ball mount platform will also allow you to switch to the other size ball.



Thule Vertex 4 Hitch Bike Rack Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier, we'll be test fitting the Thule Vertex 4 Bike Rack, part number TH9029. To being our test fit, we'll slide the shank of the bike rack into the receiver tube of the hitch. Line up the pinhole, and thread in our anti-rattle bolt,tightening it with a wrench. Now we'll go over a few clearance measurements. We have about 15 1/2" of ground clearance.The closest point of the bike rack to the rear of our Frontier is about 3". We've added about 13" to the overall length of our Nissan.We'll pull the lever at the base of the carrier and allow it to tilt away from the back of our truck.



Thule Traverse Roof Rack Installation - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier well be test fitting the Thule traverse roof rack system using part numbers THLB58, TH480, and THKIT1430. With our feet, load bars, and fit kit already assembled according to the included instructions, well place our front load bar onto the front of our roof. Well then measure 10 inches from the front part of the glass to the first part of the foot here on the passenger side. Once weve established this measurement we can then pull out the weather stripping to fit the clip into the groove on the underside of the door seal. Well then replace the weather seal back up in place and move to the drivers side. Well then repeat the same process by measuring from the glass to the foot and by removing the weather stripping to place in our clip. With this done we can use the included tensioning tool to turn the silver bolt inside of the foot to bring the clips up around tightly against the roof.



Thule AeroBlade Traverse Roof Rack Installation - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier, well be test fitting the Thule Rapid Traverse roof rack system using part numbers THARB53, TH480R, THKIT1430. With our fit kit feet and arrow blades, inaudible 00:00:16 coordinates that include instructions. Well begin our test fit by placing the front bar onto the front of our roof. Well then need to measure 10 and one-quarter inches from the front part of the glass to the first part of the foot on both the passenger and drivers side of the vehicle. This will make sure that the front load bar is perpendicular to the roof of our Frontier. With the front part in place, we can pull out the leather stripping here at the door seam to make sure the clip gets into position. Well fit the clip in place and reinstall our door seal.



Swagman Upright Roof Mounted Bike Rack Review - 2013 Nissan Frontier

Today, on our 2013 Nissan Frontier, we'll be test-fitting the Swagman Upright Roof Mounted Bike Rack, part number S64720. With a Thule Rapid Traverse Roof Rack System assembled onto our vehicle, we'll begin our test-fit by placing the bike rack up onto the bars. We'll then take the silver brackets to go on the underside of the front bar, and bring them up through the pre-drilled holes in the front of the bike rack. We'll then take the black wing nuts to thread onto the brackets to secure the front part of the bike rack to the front bar. We'll then move to the rear of the bike rack, where this time, we will slide the silver bracket down through the pre-drilled holes of the bike rack and bring the black plate on the underside of the rear bar, threading on the black wing nuts to secure the rear part of the bike rack to the rear bar. With everything all tightened down and secured, we're ready to load up our bike. We'll undo the straps at the front and rear of the bike rack, and double check to make sure our jaws are loose.



RockyMounts TieRod Roof Bike Rack Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier, we'll be test fitting the Rocky Mounts TieRod Roof Mounted Bike Rack,part number RKY1014. With the Thule RapitureVerse00:00:10Roof Rack System assembledonto our vehicle, we'll being our test fit by placing the bike rack up onto the vehicle's load bars. We'llremove the black plastic cover at the front, to bring the rubber coated steel straps around the underside of the front bar. If necessary, we can use the included Allen wrench to loosen up the straps,to be able to fit it around the bar.With the front straps in place, we can then move to the rear, remove one of the Allen bolts from the rear bracket, toslide the rear bracket around the underside of the rear bar. We'll then re-install the Allen bolts, and using the Allen wrench, tighten the rear bracket. We'll then move back up to the front and again usethe included Allen wrench to tighten the silver bolts to bring the rubber coated steel straps up around tightly against the front bar.



Rhino-Rack 4 Hitch Bike Rack Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier, we will be test fitting the Rhino Rack, four bike rack for two inch hitches, part number RBC038.We will begin our test fit by slotting the shank of the bike rack into the opening of the hitch while threading the anti rental 00:00:16 device and lock and tighten it down with a wrench. We can then secure with the lock to secure the bike rack to the vehicle.Now with the bike rack secured, we will go over a few clearance measurements to see how the two fit together. We have about 20 and inches of ground clearance. Closes part of the bike rack to the closes part of the vehicle is about 3 inches away. With the cradle arms folded down, we have added about 11 inches to the overall length of our vehicle.We can now pull a black pin at the top of the mast to swing the cradle arms out. With the cradle arms out, we have added about 28 inches to the overall length of our Frontier.





Curt Tri-Ball Mount Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier, we'll be test fitting the Curt Tri-Ball Mount for 2" hitches, part number C45001. Before I begin our test fit, we'll first inaudible00:00:11obtain the hitch height of the vehicle, which is the measurement from the ground to the inside top of the receiver tube 00:00:15.The hitch height for this vehicle is 17 and 1/4".Keep in mind that this measurement may vary due to tire size, hitch style, or after market accessories. We'll being our test fit by sliding the shank of the ball mount into the opening of the hitch and securing it with the pin and clip.Now since this ball mount has no drop or rise, if your trailer's ride height matches your vehicle's hitch height, this ball mount would be appropriate for you.The Curt Tri-Ball Mount is equipped with 3 different size balls. A 2 and 5/16" ball, a 2" ball and an inch and 7/8ths ball.This ball mount will allow you to carry different sizes and styles of trailers, without having the need to purchase additional ball mounts. With that, that'll complete today's test fit forthe Curt Tri-Ball Mount for 2" hitches, part number C45001, on our 2013 Nissan Frontier. .



Convert-A-Ball 6-Way Multi-Hitch Ball Mount Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Convert-a-Ball cushioned six-way multi-hitch ball mount for 2-inch hitches rated at 10,000 pounds, part number CAV-6W. We'll begin our test fit by sliding the shank of the ball mount into the opening of the hitch and securing it with the pin and clip. You can rotate the ball mount to access three different size balls, an 1-7/8 inch ball, a 2-inch ball, and a 2-5/16 inch ball. You can also use this ball mount with a clevis, a lunette ring or a spade. You can pull the clip at the center of the shank and lift the pin up allowing you to hook up your trailer. And that will complete today's test fit for the Convert-a-Ball cushioned six-way multi-hitch ball mount for 2-inch hitches, part number CAV-6W on our 2013 Nissan Frontier. .



Thule Sonic XXL Rooftop Cargo Box Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Thule Sonic XXL rooftop cargo box with 22 cubic feet of space, metallic silver in color, part number TH636S. With the Thule Rapid Traverse roof rack system already assembled onto our vehicle we'll begin our test fit by placing the cargo box onto the vehicle's bars. We'll then unlock the box and open the lid exposing the two closest knobs. We can then turn the knobs to bring the clamps up around tightly against each bar. You'll know when the clamps have been fully tightened when the knobs make a clicking sound. We will then close the box and move to the other side of the vehicle and repeat the same process. Now this double-sided opening lid also enables you to easily load and unload our cargo from either side of the vehicle. Once everything is all tightened down and secured that will complete today's test fit for the Thule Sonic XXL rooftop cargo box, part number TH636S, on our 2013 Nissan Frontier.



Thule Sonic Large Rooftop Cargo Box Review - 2013 Nissan Frontier

Today, on our 2013 Nissan Frontier, we'll be test-fitting the Thule Sonic Large Rooftop Cargo Box, with 13 cubic feet of space, in glossy black, part number TH634B. With the Thule Rapid Traverse Roof Rack System already assembled onto our vehicle, we'll begin our test-fit by placing the cargo box onto the vehicle's load bars. We'll unlock the box and open the lid, exposing the two closest knobs. We can then turn the knobs to bring the clamps up around tightly against each bar. You'll know the clamps have been fully tightened down when the clamps start to make a clicking sound. We can then move to the other side of the vehicle and repeat the same process. Now, this double-sided opening lid also enables you to easily load and unload your cargo from either side of the vehicle.



Thule Pulse Large Rooftop Cargo Box Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be testing fitting a Thule Pulse large roof top cargo box with 14 cubic feet of space, matte black in color, part number TH614. With the Thule Rapid Traverse roof rack system assembled onto our vehicle we'll begin our test fit by placing the cargo box onto the vehicle's bars. With this box only opening from one side we'll position the box on the passenger's side of the vehicle. We can then unlock the box and open the lid exposing the four slots in the bottom of the box. We can take the clamps, slide them down through the slots over top of each bar turning the knobs to tighten on the clamps. With everything all tightened down and secured, that will complete today's test fit for the Thule Pulse large roof top cargo box, part number TH614 on our 2013 Nissan Frontier. .



Thule Pulse Alpine Rooftop Cargo Box Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Thule Pulse Alpine rooftop cargo box with 11 cubic feet of space, matte black in color, part number TH613. With the Thule Rapid Traverse roof rack system assembled onto our vehicle we'll begin our test fit by placing the cargo box up onto the vehicle's bars. Now since this box only opens from one side you'll need to position it on the passenger's side of your vehicle. We'll then take the clamps and slide them down through the slots over top of each bar, turning the knobs to bring the clamps up around tight against the load bars. With everything all tightened down and secured that will complete today's test fit for the Thule Pulse Alpine rooftop cargo box, part number TH613 on our 2013 Nissan Frontier. .



Thule Hitching Post Pro Hitch Bike Rack Review - 2013 Nissan Frontier

Today, on our 2013 Nissan Frontier, we'll be test-fitting the Thule Hitching Post Pro 4 Bike Rack, part number TH934XTR. To begin our test-fit, we'll slide the shank of the bike rack into the receiver tube of the hitch, line up the pin hole, and thread in our anti-rattle bolt, tightening with a wrench. Now, we'll go over some clearance measurements. We have aboutfourteen and ahalfinches of ground clearance. The closest point of the bike rack to the rear of our Frontier is about seven inches. We've added about sixteen inches to the overall length of our vehicle.



Thule Force XXL Rooftop Cargo Box Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Thule Force XXL rooftop cargo box with 21 cubic feet of space, aeroskin black in color, part number TH626. With the Thule Rapid Traverse roof rack system already assembled onto our vehicle we'll begin our test fit by placing the cargo box onto the vehicle's load bars. We'll unlock the box and open the lid exposing the two closest knobs. We can then turn the knobs to bring the clamps up around tightly against each bar. We can then move to the other side of the vehicle and repeat the same process. Now this double-sided opening lid also enables us to easily load and unload our cargo from either side of the vehicle. With everything all tightened down and secured that will complete today's test fit for the Thule Force XXL roof top cargo box with 21 cubic feet of space, aeroskin black in color, part number TH626 on our 2013 Nissan Frontier. .



Thule Force Large Rooftop Cargo Box Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Thule Force large rooftop cargo box with 13 cubic feet of space, aeroskin black in color, part number TH624. With the Thule Rapid Traverse roof rack system already assembled onto our vehicle we'll begin our test fit by placing the cargo box onto the vehicle's load bars. We'll unlock the box and open the lid exposing the two closest knobs. We can then turn the knobs to bring the clamps up around tightly against each bar. We can then move to the other side of the vehicle and repeat the same process. Now this double-sided opening lid also enables you to easily load and unload our cargo from either side of the vehicle. With everything all tightened down and secured that will complete today's test fit for the Thule Force large roof top cargo box, part number TH624 on our 2013 Nissan Frontier. .



Thule Apex 4 Swing Hitch Bike Rack Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Thule Apex Swing 4 Bike Rack, part number Th9027. To begin our test fit we'll slide the shank of the bike rack into the receiver tube of the hitch, line up the pin hole and install the attached pin. Here at the rear of the shank, we'll tighten the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now we'll go over a few clearance measurements. We have about 15" of ground clearance. The closest point of the carrier to the rear of the vehicle is about an inch. We've added about 13" to the overall length of our Nissan Frontier. We'll pull the level at the top of the mast to swing out our dual arms.





Swagman Fork Down Roof Bike Rack Review - 2013 Nissan Frontier

Speaker: Today, on our 2013 Nissan Frontier, well be test fitting the Swagman Fork Down roof mounted bike rack, part number S64710 with a Thule Rapid Traverse roof rack system already assembled onto our vehicle. Well begin our test fit by placing the bike rack up onto the vehicles load bars. Well pull out our hardware. Starting at the front of the bike rack, well bring the silver brackets up around the underside of the front bar and into the pre-drilled holes at the front of the bike rack. Well then take our black wing-nuts and thread them down onto the silver bracket, securing the front part of the bike rack to the front bar. Well then repeat this process for the other side. Now, moving to the rear, this time, well take the silver bracket, slide it down through the pre-drilled holes and the wheel tray, and then, take the black plate to go on the underside of the rear bar. Well then use the included wing-nuts to tighten it down.



RockyMounts TieRod Stretch Roof Bike Rack Review - 2013 Nissan Frontier

Today, on our 2013 Nissan Frontier, we'll be test-fitting the RockyMounts TieRod Stretch Roof Mounted Bike Rack, part number RKY1011. With a Thule Rapid Traverse Roof Rack System assembled onto our vehicle, we'll begin our test-fit by placing the bike rack up onto the vehicle's bars. We'll remove the black plastic cover at the front to bring the rubber-coated steel straps around the underside of the front bar, and hook them into the connection points. We'll then move to the rear, and remove one of the Allen bolts from the rear bracket to go on the underside of the rear bar. We'll then use the included Allen key to tighten down the Allen bolts to secure the rear bracket to the rear bar. We'll then move back up to the front, and again use the included Allen key to tighten down the silver bolt to bring the straps up around tightly against the front bar. With everything all tightened down and secured, we're ready to load up our bike.







MaxxTow Adjustable-Height Ball Mount Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Maxxtow adjustable height ball mount for 2-inch hitches with a 10-inch drop or 8-inch rise rated at 5,000 pounds, part number MT70067. Before we begin our test fit we'll firstly obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17-1/4 inches. Keep in mind that this measurement may vary due to tire size, hitch style or after market accessories. We'll being our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch and securing it with the pin and clip. We can then remove the two pins here at the downward portion of the ball mount to adjust the ball mount platform to its lowest position. With the ball mount platform in its lowest position we can measure from the ground to the top of the ball platform getting a measurement of about 7-1/4 inches. We can now flip the ball mount over to the rise position and with the ball mount platform in its highest position we can again measure from the ground to the top of the ball platform getting a measurement of about 25-1/4 inches. Now, if your vehicle's hitch height matches our's, and your trailer's ride height is on or in between these two measurement in 1-inch increments, this should be an appropriate ball mount for you. That will complete today's test fit for the Maxxtow adjustable height ball mount for 2-inch hitches, part number MT70067, on our 2013 Nissan Frontier.



MaxxTow Ball Mount Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier well be test fitting the MaxxTow ball mount with two inch accessory receiver for two inch hitches rated at 5,000lbs part #: MT70066. Before we begin our test fit well first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17 and a quarter inches. Keep in mind that this measurement may vary due to the tire size, hitch style or after-market accessories. Well begin our test fit by sliding the shank of the ball mount into the opening of the hitch and securing it with a pin and clip.



Kuat Sherpa Hitch Bike Rack Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier, well be test-fitting the Kuat Sherpa Platform Style Aluminum 2-Bike Rack, part number S102. Well begin our test fit by sliding the shank of the bike rack into the opening of the hitch. Well insert our pin and secure the lock on the other side. To secure the bike rack to our Frontier, we can turn the black T-handle to engage the anti-rattle device.Now that the bike racks secured, well go over a few clearance measurements to see how the 2 fit together. We have about 18 inches of ground clearance of the rear of the bike rack. Closest part of the bike rack to the closest part of our vehicle is about 3 inches away, and weve added about 14 inches to the overall length of our truck. To lower the platform, we can pull the gold handle on the right-hand side of the base of the bike rack, and fold it down.



Kuat NV Hitch Bike Rack Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Kuat NV Platform-Style Aluminum Two Bike Rack, part number n101. We'll begin our test fit by sliding the shank of the bike rack into the opening of the hitch. Well line up the pin holes, insert our pin through the pin holes and secure with the lock on the other side. We'll then secure the Kuat NV to our vehicle by turning the black knob at the back of the shank to engage the anti-rattle device. With the bike rack secured we'll go over a few clearance measurements to see how the two fit together. We have about 15 inches of ground clearance at the rear of the bike rack.



Kuat Beta Hitch Bike Rack Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Kuat Beta Hitch Mounted Aluminum Two Bike Rack, part number b202-2. We'll begin our test fit by sliding the shank of the bike rack into the opening of the hitch. We'll line up the holes, insert our pin and lock through the holes and then turn the black knob at the back of the shank to engage the anti-rattle device. Now that the Kuat Beta is secured to our Frontier we'll go over a few clearance measurements to see how the two fit together. We have about 15 inches of ground clearance at the rear. Closest part of the bike rack to the closest part of our Frontier is about four inches away.



Hollywood Racks Traveler Tow n Go Bike Rack Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Hollywood Racks Traveler Tow and Go Three Bike Rack for Two Inch Ball Mounts, part number hr135. We'll begin our test fit by sliding the shank of our ball mount into the opening of our hitch and securing it with a pin and clip. You can also prevent rattle by using an anti-rattle device or securing to your vehicle by using a hitch lock. See our website for more details. Now for today's test fit we'll be using Hidden Hitch's Super Extra Long Shank Ball Mount rated at 6,000 pounds, part number 80232. You can use any ball mount with an extra-long shank as long as the ball mount platform exceeds more than three inches outside of your bumper.



Hidden Hitch Ball Mount with 6 Inch Drop Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Hidden Hitch Ball Mount with a 4-3/4 Inch Rise or 6 Inch Drop Rated at 6,000 pounds, part number 80240. Before I begin our test fit we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17-1/4 inches. Keep in mind that this measurement may vary due to tire size, hitch style or after-market accessories. We'll now begin our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch and securing it with the pin and clip.





Convert-A-Ball Pintle Mounting Bar Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier we'll be test fitting the Convert-A-Ball Cushion Adjustable Pintle Mounting Bar for Two Inch Hitches Rated at 10,000 Pounds, part number ampc2. Before I began our test fit we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17-1/4 inches. Keep in mind that this measurement may vary due to tire size, hitch style or after-market accessories. We'll now begin our test fit in the drop position by sliding the shank of the pintle mounting bar into the opening of the hitch and securing it with the pin and clip.



Convert-A-Ball Cushioned Weight Distribution Shank Review - 2013 Nissan Frontier

Today, on our 2013 Nissa Frontier, we'll be test-fitting the Ball Mount Adapter for a Convert-A-Ball Cushion Weight Distribution Shank, part number BA-1. We'll be using Convert-A-Ball's Weight Distribution Shank, part number AM-AC-1 for our test-fit. We'll take the ball mount adapter up to the weight distribution shank and using two pins and clip, we'll secure the ball mount adapter to the weight distribution shank. The ball mount adapter can be positioned anywhere along the weight distribution shank to accommodate different trailer's ride heights. It can also be flipped over in the rise position to allow you to accommodate different trailer ride heights. That'll complete today's test-fit for the Convert-A-Ball Ball Mount Adapter for a Convert-A-Ball Weight Distribution Shank, part number BA-1 on our 2013 Nissan Frontier. .





Convert-A-Ball Ball Mount with 8 Inch Drop Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier, we'll be test fitting the Convert-A-Ball cushioned ball mount for 2 inch hitches, with a 6 3/4 inch rise, or 8 inch drop, rated at 10,000 pounds, part number AMSC8. Before we begin our test fit, we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17 1/4 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after market accessories. We'll now begin our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch, and securing it with a pin and clip. With the ball mount secured, we can then measure from the ground to the top of the ball platform, getting a measurement of about 9 inches. If your vehicle's hitch height matches ours, and your trailer's ride height matches this measurement, this would be an appropriate ball mount for you. We can now flip the ball mount into the rise position, and again, measure from the ground to the top of the ball platform, getting a measurement of about 23 1/4 inches. Once again, if you trailer's ride height matches this measurement, this would be an appropriate ball mount for you. That will complete today's test fit for the Convert-A-Ball cushioned ball mount fro 2 inch hitches, part number AMSC8, on our 2013 Nissan Frontier.



Convert-A-Ball Heavy Duty Ball Mount with 2 Inch Drop Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier, we'll be test fitting the Convert-A-Ball cushioned ball mount for 2 inch hitches, with a 1 inch rise, or a 2 inch drop, rated at 14,000 pounds, part number AMSC2HD. Before beginning our test fit, we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17 1/4 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after market accessories. We'll now begin our test fit by sliding the shank of the ball mount, in the drop position, into the opening of the hitch, and securing it with the pin and clip. We can then measure from the ground to the top of the ball platform, getting a measurement of about 15 1/4 inches. If your vehicle's hitch height matches ours, and your trailer's ride height, which is the measurement from the ground to the bottom of your trailer's coupler, while your trailer is level, matches this measurement, this should be an appropriate ball mount for you. We can now flip the ball mount over into the rise position, and again, measure from the ground to the top of the ball platform.



Convert-A-Ball Ball Mount with 2 Inch Drop Review - 2013 Nissan Frontier

Today on our 2013 Nissan Frontier, we'll be test fitting the Convert-A-Ball cushioned ball mount for 2 inch hitches, with a 3/4 inch rise, or a2 inch drop, rated at 10,000 pounds, part numberAMSC2. Before we begin our test fit, we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is 17 1/4 inches. Keep in mind that this measurement may vary due to tire size, hitch style, or after market accessories. We'll begin our test fit by sliding the shank of the ball mount, in the drop position, into the opening of the hitch, and securing it with the pin and clip. We can then measure from the ground to the top of the ball platform, getting a measurement of about 15 inches. If your vehicle's hitch height matches ours, and you trailer's ride height matches this measurement, this would be an appropriate ball mount for you. We can now flip the ball mount over, into the rise position, and again, measure from the ground to the top of the ball platform. We'll get a measurement of about 17 1/2 inches.



Trailer Hitch Installation - 2012 Nissan Frontier - Curt

Today on this 2012 Nissan Frontier, were going to install part number 13241 from Curt. All right this is what the hitch looks once its installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories such as a ball mount, bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground will be about 18-3/4 and from the center of the hitch pin hole to the edge of the bumper will be around 3-1/4. Now well go ahead and show you how the hitch is installed.All right the first thing were going to do is go ahead and show you where the hitch will mount up to the frame. On each side of the frame close to the bumper will be three sets of threaded holes, well go ahead and point those out.



Thule XD16 Snow Tire Chains Review - 2012 Nissan Frontier

Today on this 2012 Nissan Frontier, were going to do a test fit of part number th04805265 from Thule; this is XD16 snow tire chains. A couple notes about our test fit, is that well be working with a tire size of 265/75/R16. Now were going to do a test fit on the ramp to give a better view of whats going on and how to install the chains. Well start off with our test fit by taking the yellow end of the cable on our snow chain and working form the back to the front wrapping around the backside of the tire. Then well bring both ends up to the top of the tire and connect the two. Well let it sit on top of the tire for now and then well go ahead and pull the chain over the top into the front of the tire.



Convert-A-Ball Ball Mount with 4 Inch Drop Review - 2008 Nissan Frontier

Today, on our 2008 Nissan Frontier, we're going to be test-fitting the Convert-A-Ball Cushion Ball Mount, part number AMSC4. Now, the first thing we want to do is measure our hitch height. That's from the ground to the inside top of our receiver tube. Our Frontier has a hitch height measurement of 17 inches. Now, keep in mind that this measurement will vary some even within 2008 Frontiers. Variances in tires, exact model type, and aftermarket parts, even the hitch itself, will determine the hitch height, so make sure you measure your particular vehicle.



Draw-Tite Ball Mount Review - 2008 Nissan Frontier

Today, on our 2008 Nissan Frontier, we'll be test-fitting the Draw Tite Ball Mount, part number 2923. Now, the first thing we want to do is measure our hitch height. That's from the ground to the inside top of our receiver tube. Our Frontier has a hitch height measurement of 17 inches. Now, keep in mind that this measurement will vary some even within 2008 Frontiers. Variances in tires, exact model type, and aftermarket parts, even the hitch itself, will determine the hitch height, so make sure you measure your particular vehicle.



Curt Tri-Ball Mount Review - 2008 Nissan Frontier

Today, on our 2008 Nissan Frontier, we'll be test-fitting the Curt Triball Mount Hollow Shank, part number C45001. Now, the first thing we want to do is measure our hitch height. That's from the ground to the inside top of our receiver tube. Our Frontier has a hitch height measurement of 17 inches. Now, keep in mind that this measurement will vary some even within 2008 Frontiers. Variances in tires, exact model type, and aftermarket parts, even the hitch itself, will determine the hitch height, so make sure you measure your particular vehicle.



Convert-A-Ball 6-Way Multi-Hitch Ball Mount Review - 2008 Nissan Frontier

Today, on our 2008 Nissan Frontier, we'll be test-fitting the Convertible Six-Way Multi Hitch Ball Mount, part number CAB-6W. This ball mount features six different towing methods. There are three ball sizes of 1 7/8, two-inch, and 2 5/16, and there is also the ability to use a Clevis lunette ring or spade hitch as well. Now, the first thing that we want to do is measure out hitch height. That's from the ground to the inside top of our receiver tube. Our Frontier has a hitch height measurement of 17 inches.



Convert-A-Ball Ball Mount with 2 Inch Drop Review - 2008 Nissan Frontier

Today, on our 2008 Nissan Frontier, we'll be test fitting the Convert-A-Ball Cushion Ball Mount, part number AMSC2. Now, the first thing we want to do is measure our hitch height. That's from the ground to the inside tab of our receiver tube. Our Frontier has a hitch height measurement of 17 inches. Now, keep in mind that this measurement will vary some even within 2008 Frontiers. Variances in tires, exact model type, and aftermarket parts, even the hitch itself, will determine the hitch height, so make sure you measure your particular vehicle.



Trailer Hitch Installation - 2008 Nissan Frontier - Hidden Hitch

Today on our 2008 Nissan Frontier, we'll be installing Hidden Hitch, part number 87539. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3-1/2 inches. From the top of the receiver tube to the ground is 15-1/2 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier.



Trailer Hitch Installation - 2008 Nissan Frontier - Draw-Tite

Today on our 2008 Nissan Frontier, we'll be installing the Draw-Tight Hitch, part number 75282. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 3-1/2 inches. From the top of the receiver tube to the ground is 15-1/2 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier.



Trailer Hitch Installation - 2008 Nissan Frontier - Curt

Today on our 2008 Nissan Frontier well be installing the Curt Hitch part number 13241. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 3-1/2 inches. From the top of the receiver tube to the ground is 16-1/4 inches. This will assist you with selecting accessories such as a drawbar, a bike rack or a cargo carrier.



Trailer Wiring Harness Installation - 2008 Nissan Frontier

Today on our 2008 Nissan Frontier well install the Tow Ready T1 connector, part number 118525. To begin our installation well need to access the wiring underneath the kick panel on the passengers side. Well go ahead and open up the passenger side door and remove the threshold or seal plate. Making it easier access to removing the kick panel well go ahead and remove the passenger side floor mat. Then using our trim tool or a flat bladed screwdriver well pop free the two fasteners securing the kick panel. Now well go ahead and remove the kick panel and sit it aside.



Trailer Wiring Harness Installation - 2012 Nissan Frontier

Today on 2012 Nissan Frontier we are going to install the tow ready T1 connector part number 118525. This is a two-part harness. The first piece we'll be adding to the passengers side kick panel. First, we'll remove the passenger's side threshold trim then the kick panel. To remove the trim, we'll simply take a flat blade screwdriver or a trim inaudible tool and get it underneath and pry it free from the plastic fasteners. To remove the kick panel we'll need to remove plastic screw cap and then use our trim panel tool or our flat blade screw driver to pop free the kick panel.



Trailer Wiring Harness Installation - 2012 Nissan Frontier

Today in our 2012 Nissan Frontier, we'll be installing the tow ready T1 connector part number 118263. First, we'll need to locate the manufacturer's plug located on the inside of the drivers side frame rail. As you can see here, there are two plugs. We are going to remove the cap off the gray plug. Now with the cap removed we can go ahead and take our new inaudible harness and plug it directly into the manufacturer's wiring. As we install our plug we'll make sure, we have it firmly pressed into the connector and locked in place.



Trailer Hitch Installation - 2012 Nissan Frontier - Hidden Hitch

Today in our 2012 Nissan Frontier, we'll be installing the Hidden Hitch part number 87539. This is what our hitch will look like once it's installed. Now we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch, pin hole to the out most edge of the bumper is 3-1/2 inches. From the top of the receiver, tube to the ground is 17-1/2 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier.



Trailer Hitch Installation - 2012 Nissan Frontier - Draw-Tite

Today in our 2012 Nissan Frontier, we'll be installing the draw tight hitch part number 75282. This is what our hitch will look like once it's installed. Now we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch, pin hole to the out most edge of the bumper is 3-1/2 inches. From the top of the receiver, tube to the ground is 17-1/2 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier.



Trailer Hitch Installation - 2007 Nissan Frontier

Today we will be working on a 2007 Nissan Frontier. We will be installing Draw-Tite part number 75282, which is also comparable to Hidden Hitch part number 87539. Here are a couple of measurements that will assist you with ing accessories for your new hitch such as a draw bar, a bike rack or a cargo carrier. From the center of the hitch pin hole to your outermost point of your bumper is 3-1/2 inches. And from the top of your receiver tube to the ground is 16 inches. Now let us go ahead with the installation. 0:31



Trailer Wiring Harness Installation - 2007 Nissan Frontier

Today we will be working on a 2007 Nissan Frontier. We are going to install Tow Ready T-One connector, part number 118263. The reason we have chosen this connector is because this particular model has the manufacturers tow package. :18



Trailer Hitch Installation - 2003 Nissan Frontier

Today we are going to be installing part number 13831 on a 2003 Nissan Frontier. All right, we are under the vehicle here, and we are going to go ahead and point out the mounting holes. You can see right here on the drivers side frame rail there are three holes, one large and two smaller holes. Set that over the top, where it will align through the holes. Go ahead and put our bolts down through, like that. And then we want to go ahead and do the same thing for the passenger side. as well. And now we have got the plate in place along with the bolts, we can go ahead and put the hitch up into position. We just want to attach it with the nuts that are provided.





Nissan Frontier Questions and Answers


all Nissan Frontier questions      



Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email



Only 13 Hours 31 Minutes Remaining

etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com