Mazda 6 owners are most interested in these products
change vehicle
Putco PURE Headlight Light Installation - 2007 Mazda 6
Today, in 2007 Mazda 6, we're going to install product number P230100SW from Putco. This is a pure H1 halogen headlight bulb. This is what it looked like before we install the bulbs. Now, we'll go ahead and remove the factory bulbs and install new Putco bulbs. Our headlight bulb is located on the outside of the headlight assembly towards the outside of the body. Behind this cap is the bulb and then there's a little wire latch inside it.
Trailer Hitch Installation - 2007 Mazda 6
Today on this 2007 Mazda 6 we are going to be installing Draw-Tite hitch part number 24775. This installation will also apply for Hidden Hitch part number 60846. The first thing we want to do is to go inside the trunk and remove the spare tire to get it out of our way. Moving underneath the vehicle you can see we have got dual exhaust. We want to lower down the exhaust system next to give us more room to work. There are three hangers that we are going to need to lower the exhaust off of. One here at the rear on the driver and passenger sides. If you follow forward to where the two exhausts meet there is a third hanger right there. 00:37
Trailer Hitch Installation - 2009 Mazda 6
Today we are going to be installing Draw-Tite hitch part number 24832 on a 2009 Mazda 6. OK, we are underneath the vehicle now and we want to go ahead and point out the mounting locations for the trailer hitch. Before we can do that, we actually need to lower the exhaust out of the way. To do that, we need to remove it off of three hangers. We have got one here on the passengers side, one on the drivers side, and then one dead center of the vehicle. To remove the exhaust off of its hangers, it is a good idea to spray the studs down with a spray lubricant like a WD-40. Before I remove the third forward hanger from the vehicle, I want to do two things.
Trailer Hitch Installation - 2006 Mazda 6
Today we are going to install part number 60846 from Hidden Hitch on our Mazda 6, 2006 model year. On some models, two holes have to be drilled out, basically in this general area here and right here. There is a bolt and plate that gets installed right there. Some models will have the hole pre-existing, but in this one we will have to drill them out. Our next step is to go ahead and lower the exhaust to a level where we can do our install. There are three rubber hangers to be removed: this one right here, one back in the center and then one on the passengers side also. We also put in this temporary strap here so when we lower the exhaust we have something to control it as it comes down and we can actually support it at a specified height.
Mazda 6 Questions and Answers
- Where Are the Grommets on Covercraft Floor Mat # CC76134090 That Fit a 2006 Mazda 6 Four Door
- In the picture attached is the factory drawing of the mats with the location of the grommet noted. The photos currently being used are typical catalog photos supplied by the manufacturer because we have not had a chance to take photos of these floor mats yet.
view full answer...
- Trailer Hitch and Bike Rack Recommendations fora 2004 Mazda 6 Sedan with Rear Spoiler
- After looking at some pictures of a 2004 Mazda 6 spoiler I do not believe that a trunk mount bike rack will fit without interference with the rear spoiler. The best option is going with a trailer hitch and hitch mount bike rack. The benefits of this are that the hitch can be used for other things besides a bike rack and with a hitch mount rack the bikes are kept off of the car.
For a trailer hitch you can use # C11308. Since you want to use the hitch for a bike rack you will need to use a sta
view full answer...
- Trailer Hitch and Bike Rack Recommendations for a 2004 Mazda 6
- Yes, the Curt trailer hitch with ball mount # C113083 will fit a 2004 Mazda 6. However if you just want a hitch for use with a bike rack you can save some money by getting the same hitch without the ball mount # C11308.
Since you want to use the hitch for a bike rack you will need to use a stabilization strap, # 18050, to be in compliance with Curts warranty requirements. You will also be limited to carrying 2 bikes at most with the Class I trailer hitch and will need a rack that is compatibl
view full answer...
- Trailer Hitch Recommendations for a 2005 Mazda 6 Sedan, Hatchback, or Sport Wagon
- The best way to avoid all of that is to get you the correct hitch the first time. For the 2005 Mazda 6 there is a sedan, a hatchback and a Sport Wagon. Trailer hitch # 60846 will fit the sedan and the hatchback. For the Sport Wagon you would use a hitch like # 60857.
If you are not sure if you have a hatchback or a wagon the hatchback will be about the same length as the sedan, the wagon will be longer. Hatchbacks generally have a more stubby rear end and limited cargo space whereas the longe
view full answer...
- Installation of WeatherTech All-Weather Floor Mats # WTW71 in 2013 Mazda 6
- The WeatherTech All-Weather Floor Mats # WTW71 you referenced for your 2013 Mazda 6 are semi-custom floor mats, meaning while they are not custom-made specifically for your vehicle, they are made to fit cars that are similarly designed. As such, in most cases there should be no need to trim these mats to fit in the front floorboards of your vehicle.
I have included a link to the instructions for the proper installation of this product.
If you would like floor mats that are custom made spec
view full answer...
- Can a Trunk Mount Bike Rack be Used on a 2004 Mazda 6 with Rear Spoiler
- I do have a solution for you but the spoiler on your 2004 Mazda 6 is going to interfere with the safe mounting of a trunk mount bike rack.
What you can do is install a trailer hitch, like # 24775, and use a hitch mount bike rack. For a bike rack you need one that is compatible with a Class I trailer hitch. I recommend the Swagman Titan, # S63400. This bike rack comes with anti-sway cradles, the ability to tilt down, and an integrated cable lock. It also has a rise in the shank for better grou
view full answer...
- Availability Of Bike Rack To Fit a 2005 Mazda 6 Hatchback
- I do have a way to carry bikes on your 2005 Mazda 6 Hatchback, but it is not with a trunk mounted bike rack. A trunk bike rack will not be able to be used on a 2005 Mazda 6 Hatchback model because the hatchback will not be able to carry the weight of a trunk bike rack.
I would recommend to use a hitch like the Draw-Tite Class I 1-1/4 Inch Hitch, part # 24775, along with the Thule Vertex 2 Bike Carrier, part # TH9028. I am including links to the installation instructions of the hitch and a vi
view full answer...
- SportRack Roof rack for a 2009 Mazda 6
- If you have a 4-door 2009 Mazda 6 with no existing rails or crossbars, you can use SportRack Roof Rack, # A21010S, that you have referenced. I have also included a link to the roof rack main page for your vehicle for you.
view full answer...
- Will the Thule Passage 3 Trunk Mounted Bike Rack fit a 2006 Mazda 6
- Yes, the Thule Passage 3 Bike Carrier # TH911XT that you referenced will work on your 2006 Mazda 6 as long as it is not the hatch model.
As long as you keep the contact points of the rack and your car paint clean and you do remove the rack when not in use you should not have a problem with the paint of your vehicle getting scratched.
If you will be carrying womens, childrens, or alternative frame bikes, I recommend using the bike adapter bar, # TH982XT, for greater ground clearance and to
view full answer...
- Recommended Trailer Hitch and Wiring for a 2005 Mazda 5 Wagon
- The Draw-Tite hitch # 24785 would be a good choice for your 2005 Mazda 6 Wagon, but if you are planning on towing a trailer I would recommend the CURT hitch # 11308, which includes the draw bar and a pin and clip. If you prefer, you can also go with the Draw-Tite hitch and just get the recommended draw bar and pin kit, part # 3593, separately if you need it in the future. View the installation instructions for both hitches at the included links.
To wire your vehicle, you would use circuit-pr
view full answer...
- Which Thule 3 Bike Trunk Mount Bike Racks Will Fit a 2011 Mazda 6 Sedan
- Yes, according to Thule the Raceway 3, # TH9002, will fit your 2011 Mazda 6 sedan. Thule has several 3 bike trunk mount bike racks that will fit your car.
Gateway 3, # TH9007XT
Archway 3, # TH9010
Passage 3, # TH910XT
Out of all of these bike racks, I think the Raceway 3 is the best choice. It is very light weight, under 13 pounds, and the retractable cables make it quick and easy to install. Out of all of the trunk mounted bike racks I have used, the Raceway has been the easiest to inst
view full answer...
- Position of Footplate Handles and Plunger Pins on Landing Gear Trailer Jacks
- From what I have seen, there are 2 different configurations for landing gear jacks like # BD182815. First is like the jack you have referenced that has the foot release is perpendicular to the rod through the top center of the jack. The other configuration is like # BD182411, with the release parallel with the top rod.
Jack # BD182411 is a companion to the Bulldog Square Jack # BD182400. The Bulldog Square Jack, # BD182404 and can be used in tandem operations with either of the first two jack
view full answer...
- Yakima Trunk Mount Bike Rack Recommendations for 2004 Mazda 6 Wagon
- There are three different Yakima bike racks that will work on the trunk of your 2004 Mazda 6 wagon, and the Yakima QuickBack 2 Bike Rack, part # Y02621, that you referenced is one of them.
You can use one of the following:
Yakima KingJoe 2 Bike Trunk Mounted Rack, part # Y02619
Yakima QuickBack 2 Bike Trunk Mounted Rack, part # Y02621
I attached installation instructions for all of these products below, as well as a review video of the # Y02619, and # Y02616.
I have also included a
view full answer...
- Tips for Installing Hidden Hitch 1-1/4 Trailer Hitch 60857 on a 2007 Mazda 6 Sport Wagon
- You should be able to just pop out the two rubber plugs in the trunk pan of your 2007 Mazda 6 Sport Wagon, using a flat head screwdriver or trim removal tool. Hidden Hitch model # 60857 does not require you to lower your exhaust to complete the installation, as the entire hitch assembly runs along the center of the vehicle, between the exhaust.
Once you have popped out the two plugs, move straight back from these holes, staying in the center of the vehicle. Once you reach the inner bumper str
view full answer...
- How Do You Replace Low Beam Lights on 2004 Mazda 6
- I can relate to your problem, my car uses the same type of bulb and there is also very little room to get your hand in to change the headlight bulb.
I did some research and found that other Mazda 6 owners run into the same problems. I found that to provide additional room there are a few things you can unbolt or remove temporarily.
Before you begin, it is best to disconnect your negative battery terminal. Also, when replacing the bulbs, you will want to make sure to wear gloves as it is i
view full answer...
- Will the Draw-Tite Sportframe Trailer Hitch, # 24785, Fit a 2007 Mazda 6 Hatchback And Wagon
- The Draw-Tite Sportframe Trailer Hitch, item # 24785, will fit the 2007 Mazda 6 Sport Wagon models only.
For the 2007 Mazda 6 five door hatch back, and the 4 door sedan, you would need to use the Draw-Tite Sportframe Trailer Hitch, item # 24775.
Some items you may need to complete your Class I towing setup are listed below.
Wiring, item # 119176KIT, for the 2007 Mazda 6 Sport Wagon
Wiring, item # 118405, for the Mazda 6 4 Door Sedan and 5 Door Hatchback
Drawbar, item # 3593, for the
view full answer...
- Tire Chains for a 2008 Mazda 6 with 215/50-17 Size Tires
- We actually do have several snow tire chain options for your 2008 Mazda 6 and 215/50-17 tires. I have included a link to the available options below. On the product page for each of the chains, you can scroll down near the end of the page to see a list of tire sizes the chains will fit to verify whether or not your tire size is represented.
It is also a good idea to follow the specifications in the owners manual for your vehicle. If it states tire chains are not to be used, there could be a c
view full answer...
- Which Roof Rack and Carrier Would Work Well for a 2007 Mazda 6 Sedan and a 14 Foot Tandem Kayak
- I should be able to put together a list of parts for a roof rack and kayak carrier for you. Just a couple of quick questions would help narrow things down.
Do you have a preference as far as Yakima or Thule for the roof rack or carrier? And second, what is the size of the kayak? Lenght, width and weight?
view full answer...
- Will Draw-Tite Trailer Hitch, # 24832, Fit on a 2009 Mazda 6 with Single Exhaust
- Yes. The Draw-Tite Trailer Hitch, # 24832, will fit your 2009 Mazda 6 with single exhaust. I have included a link to the instructions below.
I also recommend the Tow Ready Custom Fit Vehicle Wiring, # 118483. This is a T-one style harness with circuit protected modulite. The connectors plug in line with your Mazdas wiring and provide a 4 pole connector at the rear of the vehicle. The modulite requires a direct connection to the battery in order to protect your vehicles sensitive wiring. I hav
view full answer...
- Where to Connect the Wires On a 2007 Mazda 6 Sport Wagon
- Wiring the Mazda 6 sport Wagon for a 4-Way trailer connection is pretty easy. We do not have a specific wiring diagram for the Mazda 6 Sport Wagon but the only directions that would be different is how to get to the tail light wiring behind the tail lights. All I can tell you at this time is that you will need to figure out how the tail lights are installed and remove them or access their wiring somehow. Many times this requires removing interior panels on each side of the vehicle.
Once you
view full answer...
all Mazda 6 questions
