Select Your Vehicle
view cartView Cart
Only 23 Hours 55 Minutes Remaining

Kia Sedona owners are most interested in these products

change vehicle



Kia Sedona Videos

Rola Sport Series Roof Rack Installation - 2006 Kia Sedona

Today on our 2006 Kia Sedona we'll be test fitting the Rola Sport Series Roof Rack with RBU Mounting System for Raised Factory Side rails, part number 59899. To being our test fit we'll slide our front crossbar onto the front of our roof. We'll then measure from a fixed point on our raised side rails to get the front crossbar perpendicular to the roof.We'll measure this on the both the passenger and driver's side of the vehicle. Once we've established this position we can turn the black T-handles that tighten down the claws to secure the front crossbar to the raised side rails of our vehicle. We'll then push in the T-bolts and using the key lock them inside of the claw.We'll then place our rear crossbar onto the rear of our roof and measure the crossbar spread. The crossbar spread is the measurement from the center of the front crossbar to the center of the rear crossbar.



Rola Sport Series Roof Rack Review - 2006 Kia Sedona

Today on our 2006 Kia Sedona we'll be test fitting the Rola Sport Series Roof Rack with RBU Mounting System for Raised Factory Side Rails, part number 59898. To begin our test fit we'll place the front crossbar onto the roof of our vehicle. We'll slide the jaws onto the raised side rails and measure from a fixed point on the side rail to make sure that the crossbar is equal from that side point on both sides ensuring the crossbar is perpendicular to the roof of our Sedona.We'll measure this on both the passenger and driver's side of the vehicle. Once we've established this position we can turn the black T-handles to tighten down the jaws to our factory raised side rails. Once we got them all tight we can push them in and use the key to lock them in place.We'll now load our rear crossbar onto the rear of our roof, slide the brackets onto the raised side rails and measure the crossbar spread. The crossbar spread is the measurement from the center of the front crossbar to the center of the rear crossbar.



Trailer Wiring Harness Installation - 2006 Kia Sedona

Today, on this 2006 Kia Sedona, we're going to install Part Number 118410 from Tow Ready. This is our T-One Wiring Harness. To start off our install, we're going to open up the back hatch and then we're going to remove the tail lights. There's three screws in each side and then we can go ahead and remove the tail light by pulling it off to the side. We'll hold the tail lights, so we can see the mounting points on the side, but you can see how the tail lights attach to the vehicle. To disconnect the wire harness, there's a small tab on the wire harness that we push down to release it then we can go ahead and pull it apart.



Rain-X Fusion Wiper Blades Installation - 2012 Kia Sedona

Today on our 2012 Kia Sedona, well be installing the Rain-X Fusion Windshield Wiper Blades using part number RX880009 and part number RX880003. Now well begin the installation by removing the old wiper blade here on the driver side. Well simply lift it up away from the windshield; push on the tab here releasing it from the J-Hook where well remove it from the J-Hook on the wiper arm. With it removed, well take our new Rain-X Fusion wiper blade, slide it onto the J-Hook and clip down the clip holding it in place. Well then allow it to lie back down on the windshield, which will complete the installation of the driver side. We can then move over to the passenger side where well repeat the same process using the 18 inch blade.



Trailer Brake Controller Installation - 2003 Kia Sedona

Today on our 2003 Kia Sedona well be installing the ETBC7 brake controller install kit and our Tekonsha Prodigy P3 brake controller, part number 90195. Well first need to disassemble the interior of the vehicle to gain access to the wiring. Our first step will be removing the rear threshold. To do this well remove the fastener caps. Once we have the fastener caps out of the way we can then go ahead and remove the Phillips screws fastening the rear threshold. Once we have those out of the way well go ahead and set the threshold aside for reinstallation later.



Trailer Hitch Installation - 2006 Kia Sedona - Curt

Today, on our 2006 Kia Sedona were going to install part number C13345 from Curt. This is what the hitch looks like when its installed on the vehicle. Next, well give you some measurements to help you out in selecting some accessories such as a ball mount, bicycle rack, or a cargo carrier. From top of receiver opening down to the ground will be 12-1/4 inches, and from center of the hitch pin hole to the edge of the bumper is going to be about 5-1/2 inches. Now Ill go ahead and show you how the hitch is installed.First thing we want to do is go ahead and point out the mounting locations from the hitch. Looking at the drivers side frame rail, therere three threaded holes.



Trailer Hitch Installation - 2006 Kia Sedona - Hidden Hitch

Today on this 2006 Kia Sedona were going to install part number 70761 from Hidden Hitch. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements to help you out in selecting some accessories, such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the edge of the bumper is going to be about four and a half inches, and from the top of the receiver opening down to the ground will be about 12 inches. Now well go ahead and show you how the hitch is installed. The first thing well do, well go ahead and show you where the mounting points are on the frame.



Trailer Hitch Installation - 2012 Kia Sedona - Curt

Today on this 2012 Kia Sedona were going to install part number c13345 from Curt. This is what the hitch looks like when its installed on the vehicle. Next well go ahead and give you some measurements that will help out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground will be 12-1/4 inches and from the hitch pin hole to the edge of the bumper will be 5-1/2 inches. Now well go ahead and show you how the hitch is installed. First thing we are going to do is go ahead and lower the exhaust and get it out of the way.



Rain-X Latitude Wiper Blades Installation - 2012 Kia Sedona

Today on this 2012 Kia Sedona were going to do a test fit of part number rx5079281 from Rain-X. This is a latitude windshield wiper blade; this is designed to be all weather replacement blade for use of rain, snow, and sleet. It has a bean style design that gives even pressure across the windshield and the rubber squeegee also has UV inhibitors to help protect it from the sunlight. The first step is go ahead and remove your original windshield wiper blades, well go ahead and push on the small tab here and well slide them off, once its removed you can see we have a J-arm style connection. Now well take our new latitude windshield wiper blade, well line up the arm with the attachment point and well slide it in place. Well go ahead and lower your windshield and see how it contours to the shape.





Glacier Cable Snow Tire Chains Review - 2012 Kia Sedona

Today on our 2012 Kid Sedona well be test fitting the Glacier cable snow tire chains, part number PW1038, with tire size P225/70/R16s. Now to begin our test fit well need to lay the chains out on the ground and make sure we get any kinks or knots out of the chains. With that done well identify the correct way to mount the chains to the tire. Youll notice that on the side cable here where the cross chain attaches, in other words tire side. Well make sure that these face the tire when we mount our cable chains. Well now drape them over the tire and make sure that our cross chains are centered with our tire tread.



Thule Apex 4 Hitch Bike Rack Review - 2012 Kia Sedona

Today on our 2012 Kia Sedona, we'll be test fitting the Thule Apex 4 Bike Carrier, part number TH9025. To begin our test fit, we'll slide the shank of the carrier into the opening of the hitch, line up our pin holes, and insert the spring loaded pin into the pin hole. We'll then turn the black knob located at the base of the carrier to engage our anti-rattle device. Now, let's go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 11 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 2 inches.



Trailer Wiring Harness Installation - 2012 Kia Sedona

Today, on this 2012 Kia Sedona, we're going to install part number 118410 from Tow Ready. First thing we need to do is go ahead and open the tail gate and get access to the tail lights to remove both of them. They'll be three screws in each light, so to remove the tail light you will pry the light away from the vehicle. We'll disconnect the wire harness from the tail light. There will be a small tab that you have to push down and then we can go ahead and release the light from the wire harness. Next, we will go ahead and take the four pole wire and run it down between the bumper cover and the body of the vehicle.



Rain-X Weatherbeater Wiper Blades Installation - 2012 Kia Sedona

Today on this 2012 Kia Sedona were going to do a test fit of part number RX30226 from Rain-X. This is a weather beater windshield wiper. A few things to know about this windshield wiper blade that its designed to be OEM replacement. This also has a frame style design with multiple pressure points that helps give it even pressure across the windshield. It has all natural rubber edge with built in UV inhibitors to help protect the squeegee from damaging effects of the sun. To start off our test fit well go ahead and remove the original windshield wiper blades.



Pro Series Q-Slot Hitch Bike Rack Review - 2012 Kia Sedona

Today on this 2012 Kia Sedona were going to do a test fit of part number PS63134. A few things to know about this bicycle rack is that it will work with inch and a quarter receiver hitches, both Class I and Class II. This will also work with two inch receiver hitches with the included spacer. Thats what well be working with today. Well start off our test fit by installing the bike rack into the hitch, then installing the pin and clip. Then well go ahead and get some clearance measurements.



Thule Hitching Post Pro Hitch Bike Rack Review - 2012 Kia Sedona

Today on this 2012 Kia Sedona were going to do a test fit of part number TH934XTR from Thule. One thing to know about this bicycle rack is that when you use it with a class one receiver hitch remember to carry just two bicycles. Now to start off our test fit well go ahead and put the bicycle rack into the hitch and then well go ahead and tighten down the anti-rattle bolt. Then well go ahead and get some clearance measurements. From the bumper to the security cable loop on the bike rack the minimum clearance is going to be 5 inches. Ground clearance is going to be about 9 inches.



Swagman Titan Hitch Bike Rack Review - 2012 Kia Sedona

Alright, today on a 2012 Kia Sedona were going to do a test fit of part number S63410 from Swagman. This is their titan bicycle rack. A few things to know about this bicycle rack that it will work off an 1-1/4 receiver hitches, both class 1 and class 2 and this will also work with 2 inch receiver hitches with the included spacer and thats what were working with today. Well start off our test fit by installing the bike rack into the hitch and then well tighten down the anti-rattle bolt and put the safety pin on the other side. Then well get some clearance measurements. From the bike rack to the bumper will be about 6 inches as closest point.



SportRack Escape 3 Hitch Bike Rack Review - 2012 Kia Sedona

Today on this 2012 Kia Sedona were going to do a test fit of part number A30403 from Sportrack. All right a couple things to know about this bike rack is it will work with an inch and quarter receiver hitches, class two only. This will also work with two inch receiver hitches with the included spacer and thats what well be working with today. Now install for test fit by taking the bicycle rack installing it into the hitch then tighten down the anti-rattle bolt and installing the clip on the other side. Now well go ahead and get some clearance measurements. From the bike rack to the bumper at its closest point will be about two inches.



Hidden Hitch Ball Mount with 6 Inch Drop Review - 2012 Kia Sedona

Today on this 2012 Kia Sedona were going to do a test fit of part number 80240 from Hidden Hitch. To start off well get a reference point. Well measure from the top of the receiver opening down to the ground. This will be 11-3/4 inches. Alright, now well take our ball mount and hold it in place to the hitch pin and well get some measurements. From where the ball mounts on to the ball mount down to ground is going to be about 6 inches.



Draw-Tite Ball Mount Review - 2012 Kia Sedona

Today on this 2012 Kia Sedona were going to do a test fit of part number 2923 from Draw-Tite. Before we begin our test fit were going to get a measurement of our hitch on our vehicle right now. That measurement will be 11 3/4. Now well take our ball mount and well go ahead and install it in the hitch. Well secure it with a hitch pin and well get some clearance measurements. First well measure the ball mount in the rise position.



Curt Tri-Ball Mount Review - 2012 Kia Sedona

Today on this 2012 Kia Sedona were going to do a test fit of part number C45001 from Curt. Were going to start off our test fit by getting a measurement from the top of the receiver tube down to the ground for reference point. Our measurement is going to be 11 inches. Well take our ball mount and go ahead and install it in the hitch and secure it with a hitch pin. Since our ball mount is going to have the same height as the hitch measurement because its straight. Well get a measurement on top of the hitch ball and also ground clearance measurement as well.



Trailer Brake Controller Installation - 2008 Kia Sedona

Today, on our 2008 Kia Sedona, well be installing the Draw-Tite Brake Controller, part number 5100. Well be connecting with our ETBC-7 install kit. Well also be using the Tow-Ready Universal Mounting Bracket, part number 18136. Our first step will be assembling the 7-pole mounting bracket to the 7-pole connector. Well be using the hardware provided with our install kit. With that completed, we can now go ahead and connect the 7-pole bracket to the tow ready universal mounting bracket.



Trailer Wiring Harness Installation - 2010 Kia Sedona

Today on our 2012 Kia Sedona well be installing part #: 118410 from Tow Ready, the T1 vehicle wiring harness. Well start by removing our taillights. We have three fasteners to remove. To remove our taillight wiring harness well push down this tab right here, we can pull it apart. Were going to take our purple wire and put it between the bumper and the body and run it all the way out towards the bottom. Now there are some supports in there that you have to work it around so it may take some practice.



Trailer Hitch Installation - 2010 Kia Sedona - Curt

Today in this 2010 Kia Sedona were going to install part number c13345 from Curt. Alright this is what the hitch looks like once installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories. From the center of the hitch pin opening to the edge of bumper were looking at five and three quarter inches and from the top to the receiver opening down to the ground is 11 inches. No well go ahead on how the hitches installed and the hitches install some frame here, here and here. Let me just thread a holes on the frame but we need some time up to clean.



Trailer Hitch Installation - 2012 Kia Sedona - Draw-Tite

Today on this 2012 Kia Sedona we're gonna install part number 75421 from Draw-Tite. Alright! This is what the hitch looks like when it's installed on the vehicle. Next we'll give you some measurements that will help you out in selecting some accessories such as a bike rack or a cargo carrier. From the center of our hitch pin hole to the outside edge of the bumper is going to be 4-1/2 inches and from the top of the receiver opening down to the ground will be 12 inches. Now we'll go ahead and show you how the hitch is installed. The first step in our install is to go ahead and get the exhaust out of the way so we can see the one, two, three attachment points for the hitch.



Trailer Hitch Installation - 2012 Kia Sedona - Hidden Hitch

Today on this 2012 Kia Sedona, were going to install part number 70761 from Hidden Hitch. Alright, this is what the hitch looks like when its installed on the vehicle. Next, well give you some measurements to help you out in selecting some accessories such as a bike rack or a cargo carrier. From the center of the hitch pinhole to the outside edge of the bumper is going to be 4-1/2 inches and from the top of the receiver opening down to the ground will be 12 inches. Now, well go ahead and show you how the hitch is installed. The first step in our install is to go ahead and get the exhaust out of the way.



Pro Series Eclipse 4 Hitch Bike Rack Review - 2012 Kia Sedona

Alright, today on this 2012 Kia Sedona, we're going to test fit part number 63124 from Tow Ready. This is the 4 Bike Hitch Mounted Folding Carrier. A couple of things to know about this bicycle rack, that it's designed to work with 2-inch receiver hitches only and we'll start off our install by installing the bike rack into the hitch, then we'll go ahead and tighten down the anti-rattle bolt. Then we'll go ahead and install the clip on the other side. Alright, now we can go ahead and get some clearance measurements. From the bumper to the bike rack, we're looking at 3-3/4 inches.



Thule Apex 4 Swing Hitch Bike Rack Review - 2012 Kia Sedona

Alright, today on this 2012 Kia Sedona, we're going to do a test fit of part number TH9027 from Thule. This is their Apex Swing 4 Bike Carrier. One thing to know about this bicycle rack is it's designed for 2-inch receiver hitches only. We'll go ahead and start our test fit by installing the bike rack into the hitch. We'll make sure that the integrated hitch pin snaps into the hitch pin hole. We'll put it back a little bit, put some tension on it, and then tighten down the anti-rattle knob.



Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2012 Kia Sedona

Alright, today on this 2012 Kia Sedona, we're going to do a test fit of part number S64670 from Swagman. This is their XTC2 Bicycle Carrier. Two things to know about this bicycle carrier is that it will work with 1-1/4-inch receiver hitches both Class 1 and Class 2 and this will also work with 2-inch receiver hitches with the provided spacer, and our vehicle today has a 2-inch receiver hitch. We'll start off our test fit by installing the bike rack into the hitch. We'll tighten down the anti-rattle bolt and then install the clip on the other side. Let's go ahead and fold the bike rack and get some clearance measurements.



Rhode Gear Highway Hitch Bike Rack Review - 2012 Kia Sedona

Alright, today on this 2012 Kia Sedona, we're going to do a test fit of part number RG8015220 from Rhode Gear. This is our Highway 2 Bike Carrier. A few things to know about this bike carrier, is that it will work with 1-1/4-inch receiver hitches both class 1 and class 2. This will also work with 2-inch receiver hitches with the included spacer, and our vehicle does use a 2-inch receiver hitch. We'll start off our test fit by installing the bike rack into the hitch. We'll tighten down the anti-rattle bolt and install the clip on the other side.



Curt 20x60 Folding Aluminum Cargo Carrier Review- 2012 Kia Sedona

Alright, today on this 2012 Kia Sedona, we're going to do a test fit of part number C18100 from Curt. This is the hitch cargo carrier. A couple of notes about this cargo carrier, that it is designed to fit 2-inch receiver hitches only and has a weight capacity of up to 500 pounds. Now, check the ratings on your hitch because some 2-inch receiver hitches are rated for a little bit lower. We'll start off out test fit by installing the cargo carrier into the hitch and we'll go ahead and install the pin and clip. Now, the pin and clip is not provided with the cargo carrier.



Yakima RailGrab Roof Rack Installation - 2012 Kia Sedona

Today we're going to be test fitting the Yakima RailGrab Roof Rack for models with factory installed roof rails on our 2012 Kia Sedona. With our bars already preassembled we'll go ahead and fit them to the vehicle. We'll begin by placing the front bar towards the front of the vehicle on the side bars. We'll want to find a fixed point on the side rails to measure from. We'll measure from that fixed point to the leading edge of the foot. With both feet in the same position we can go ahead and make sure that the crossbar is centered with the vehicle from left to right.



Yakima LoadWarrior Roof Cargo Basket Review - 2012 Kia Sedona

Today on our 2012 Kia Sedona, we'll be test fitting the Akima Roof Cargo Carrier, part number Y07070. Our vehicle is already equipped with the Akima Rail Grab Roof Rack System and our cargo basket is already pre-assembled, so we're ready to go ahead and fit it to the vehicle. We'll begin by setting the basket on top of the crossbars. We'll then center it from the left and right, at which point we'll secure it to the vehicle using the provided hardware. With all eight wind nuts tied on the hardware, our basket is secured and we're ready to go ahead and load it. And that completes our test fit of the Akima Roof Cargo Carrier, part number Y07070, on our 2012 Kia Sedona..



Thule MOAB Roof Top Cargo Basket Review - 2012 Kia Sedona

Today on our 2012 Kia Sedona, well be test fitting the Thule Moab, part number TH690. With our Thule AeroBlade Crossbars set at 28-inch spread and our cargo basket already pre-assembled, were ready to go ahead and fit it to the vehicle. Well begin by setting the basket on top of the crossbars. Well center it from left to right. At that point, we can tighten it down using the included hardware. With the hardware tight, well now go ahead and install the hardware covers.



Thule MOAB Roof Top Cargo Basket Review - 2012 Kia Sedona

Today on our 2012 Kia Sedona, well be test fitting the Thule Moab, part number TH690. With our vehicle already equipped with the Thule Crossroad Roof Rack and our Basket already pre-assembled, were ready to go ahead and fit it to the vehicle. Well begin by setting the basket on top of the crossbars. Well center it with the vehicle from left to right. Well then tighten it down using the provided hardware. With the basket clamps tightened down, our basket is secure.



Thule Flat Top Ski and Snowboard Carrier Review - 2012 Kia Sedona

Today on our 2012 Kia Sedona, well be test fitting the Thule Universal Flat Top Rooftop Snow Sport Carrier, part number TH92725. With our vehicle equipped with the Thule AeroBlade Roof Rack and our Ski Carrier already pre-assembled, were ready to go ahead and mount it to the vehicle. Well begin by placing the front carrier on the front crossbar. Well line it up and tighten it down using the rubber-coated metal straps. Now that the front carrier is installed, well go ahead and move to the rear. Again well set it on top of the rear bar, line it up with the front bar, and tighten it down using the rubber-coated straps.



Rola Roof Cargo Basket with RailGrab Bars Installation - 2012 Kia Sedona

Today on our 2012 Kia Sedona, well be test fitting the Rola Roof Mounted Cargo Basket, part number 59504. Our vehicle is already equipped with the Yakima Railgrab Roof Rack System and our Cargo Basket is already pre-assemble, so well go ahead and fit it to the vehicle. Well begin by setting the basket on top of the crossbars. Well then center it from the left to right of the vehicle. After that, well go ahead and tighten it down using the provided hardware. With our hardware tight, our roof basket is installed and ready to be loaded.



Rola Roof Cargo Basket with AeroBlade Bars Installation - 2012 Kia Sedona

Today on our 2012 Kia Sedona, well be test fitting the Rola Roof Mounted Cargo Basket, part number 59504. With our vehicle already equipped with the Thule 47-inch AeroBlade Crossbars and our Roof Basket already pre-assembled, were ready to go ahead and fit it to the vehicle. Well begin by placing the basket on top of the crossbars, centering it from left to right on the vehicle. Well then tighten it down using the included hardware. With the hardware tight, the cargo basket is secure and were ready to go ahead and load it up. And that completes our test fit of the Rola Roof Mounted Cargo Basket, part number 59504 on our 2012 Kia Sedona..



Rola Roof Cargo Basket Installation - 2012 Kia Sedona

Today on our 2012 Kia Sedona, well be test fitting the Rola Roof Mounted Cargo Basket, part number 59504. With our vehicle already equipped with the Thule Crossroads Roof Rack System, and our crossbar space set at 30 inches, with our cargo basket pre-assemble, were ready to go ahead and fit it to the vehicle. Well begin by setting the basket on top of the crossbars. Well center it from left to right. Well then tighten it down using the included hardware. With the 8-wing nuts tightened down, our cargo basket is secured and were ready to load it up.



Thule Crossroad Roof Rack Installation - 2012 Kia Sedona

Today on our 2012 Kia Sedona, well be test fitting the Thule Crossroad Roof Rack using the 50 inch square bars, part number THLB50 and the Thule Crossroad Roof Mounted Rail Foot Pack, part number TH450. With our vehicle already equipped with the factory side rails and our roof rack already pre-assembled, were ready to go ahead and mount it to the vehicle. We begin by placing the front crossbar on top of the vehicle. Well need to center the crossbar from left to right. Well also need to make sure that the triangles on each to the feet are centered over the side rails. We also need to locate a fixed point on each of the side rails to do a measurement.



Thule AeroBlade Crossroad Roof Rack Installation - 2012 Kia Sedona

Today on our 2012 Kia Sedona, well be test fitting the Thule AeroBlade Crossroad Roof Rack part number TH450R and part number THARB47 with our vehicle already equipped with the factory roof rails and our crossbars already pre-assembled, were ready to go ahead and fit them to the vehicle. Well begin by setting the front crossbar on top of the vehicle. Well need to center it from left to right and ensure that the triangles on each foot are over the side rails. At that point, we can go ahead and tighten it down using the included Allen tool in each foot. With the each foot snuggling in place, you do need to make sure that your crossbar is square. To do this, find a fixed point on the side rails and measure to the foot with the tape measure.



Rhino Rack Roof Rack Installation - 2006 Kia Sedona

Today on this 2006 Kia Sedona with factory raised side rails we are going to be installing a Rhino roof rack part number SXB3. We already have our crossbar assemblies put together so now we are ready to mount them on our vehicle. First we will set our front crossbar assembly up on the side rails. Before we start tightening down we are going to check to make sure the crossbar is overhanging evenly on both sides. We also need to ensure that the crossbar is running perpendicular to our factory raised side rails. To check this we are going to measure from the front end of our side rail to the leading edge of our feet on our Rhino Rack roof rack. We will make sure it is the same on both sides so that we know the crossbar is perpendicular to the side rails. Once we have checked all of our measurements and ensured the crossbar is into position we can go ahead and tighten it down. We will take the included allen key and move back and forth from the passenger side to the driver side tightening down the roof rack systen evenly. This will help ensure that we do not lose our positioning and that we do not have too much tension on one side or the other. As we tighten the allen head bolt our rack base will clamp onto the side rails and it will also lock onto our crossbars. Once we have the front crossbar tightened down we are ready to move to the rear of the vehicle.



Trailer Hitch Installation - 2010 Kia Sedona

Today on this 2010 Kia Sedona, we are going to install part number 70761 from Hidden Hitch. This will also apply to part number 75421 from Draw-Tite. This is what the hitch looks like installed on the vehicle. Next we will give you some measurements that will help you our when ing a ball mount, bike rack, or cargo carrier. From the top of the receiver opening to the ground is 12 inches. From the center of the hitch pin to the outside edge of the bumper is 4-3/4 inches. Now we will show you how the hitch is installed on the vehicle. :31



Trailer Hitch Installation - 2006 Kia Sedona

Today on this 2006 Kia Sedona we will be installing Valley hitch part number V81572. Before we get started with the hitch installation we are going to give you a couple of final installed dimensions that will help make choosing your hitch accessories a little bit easier. From the top of the receiver tube opening to the ground is going to measure 11 inches. From the center of the pin hole to clear the rear edge of the bumper is going to measure approximately 7 inches. Now we will move on to the installation. 00:24



Trailer Hitch Installation - 2008 Kia Sedona

Today on this 2008 Kia Sedona we are going to install part number 70761 from Hidden Hitch. This will also apply to part number 75421 from Draw-Tite. The first thing we need to do is lower the exhaust and get it out of the way. To lower the exhaust we are going to remove these two bolts on this hanger. Next we will move up towards the front of the vehicle and remove the two rubber hangers for the muffler. :34



Trailer Wiring Harness Installation - 2008 Kia Sedona

Today on this 2008 Kia Sedona we are going to install part number 118410 from Tow Ready. The first steps involved is get into the back of the vehicle, pull up the hatch, and then get to the fasteners that hold the tail lights in place. We have got three fasteners to remove and then pop the light off. Now we will disconnect the tail lights from the wire harness. Push down this little tab and this connector will come apart. Now we will go over to the passenger side of the vehicle and do the same thing one more time. 00:36



Trailer Wiring Harness Installation - 2006 Kia Sedona

Today were going to show you a popular upgrade. We have here a four pole flat that has been installed on a vehicle. The owner has a boat trailer now and it has a five wire flat. So were going to convert that four wire to a five wire flat. We will show you how to deal with part number 20036 which is the adapter itself, and the bracket which is part number 20046. Our first step we need to do is take off the four pole and then well uninstall the bracket and put in the new bracket. It may take some force, but you have to pull to get this out of here. We actually used a rubber mallet to tap it a little bit, now this bracket can come off which we have previously loosened up. Now well install our new bracket and it will go in the same spot as before. What were going to do next is get our four pole ready which we have cleaned out with WD-40 and then were going to put in some dielectric grease. Well put that inside here and then were going to attach our four pole from our adapter inside there.





Kia Sedona Questions and Answers


all Kia Sedona questions      



Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email



Only 23 Hours 55 Minutes Remaining

etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com