Jeep Wrangler Unlimited owners are most interested in these products
change vehicle
Hollywood Racks SR2 Spare Tire Mount Bike Rack Review - 2013 Jeep Wrangler Unlimited
Today on our 2013 Jeep Wrangler Unlimited, well be test fitting the Hollywood Racks Spare Tire Mount SR2 2 Bike Carrier, part number HRSR2. Now with our spare tire removed from the vehicle and our center cap taken out of the spare tire, well place the black backplate of the carrier onto the lug studs. Well then pick up our spare tire and slide the spare tire onto our Wranglers lug studs. Well then replace the lug nuts and tighten it down using a wrench. This will secure the backplate of the carrier to the vehicle. Well now place the carrier onto the vehicle by sliding the open tube onto the square tube of the backplate then using one of the included bolts; well thread through the carrier and tighten it down with the included wrench. This will secure the carrier to the vehicle.
Yakima SpareTime Spare Tire Mount Bike Rack Review - 2013 Jeep Wrangler Unlimited
Today on our 2013 Jeep Wrangler Limited well be test fitting the Yakima Spare Time spare tire mount two bike carrier part #: Y02598. Before we begin our test fit we will first need to remove the spare tire of the vehicle. With a wrench well first loosen up the lug nuts. Well then remove the lug nuts to remove the spare tire. After removing the spare tire well need to knock out the center cap. Well then place the black plate of the spare tire mount onto the lug studs.
Trailer Wiring Harness Installation - 2013 Jeep Wrangler Unlimited
Today on our 2013 Jeep Wrangler Unlimited well be installing Tow Ready T-1 connector, part number 118416. To begin our install well need to remove the drivers side taillight assembly. Well remove the two inside screws and then pop the taillight assembly out of its position. Here we can gain access to the manufacturers wiring and well disconnect the taillight assembly from the wiring by pressing on the locking tab and pulling the connectors apart. Next, well set the taillight assembly aside and take our Tow Ready Harness and feed it down through the opening and then underneath the foam cover at the bottom of the drivers side quarter panel. This will feed our four pole underneath the vehicle.
Convert-A-Ball Ball Mount with 4 Inch Drop Review - 2012 Jeep Wrangler Unlimited
Today, on our 2012 Jeep Wrangler Unlimited, we'll be test fitting the convertible cushion ball mount for two-inch hitches with a two and 3/4 inch rise or a four-inch drop rated at 10,000 pounds. Part number AMSC4. Now, before we install our draw bar, we'll first need to get our hitch hike measurement. To do this,we'll measure from the top of the receiver tube to the ground. Now, on this vehicle, that measurement is 23-1/2 inches. Now keep in mind, this measurement can change dut to tire size, hitch style or any other accessory that may affect vehicle right height.
Convert-A-Ball Ball Mount with 2 Inch Drop Review - 2012 Jeep Wrangler Unlimited
Today on our 2012 Jeep Wrangler Unlimited, well be test fitting the Convert-A-Ball Cushion Ball Mount for 2-inch hitches with a 3/4 inch rise or 2-inch drop rated at 10,000 pounds, part number AMSC2.Before we install our drawbar, well first need to get our hitch height measurement. To do this well measure from the top of the receiver tube to the ground. On this vehicle that measurement is 23-1/2 inches. Keep in mind this measurement can change due to tire size, hitch style, or any other accessory that may affect vehicle ride height. Its a good idea to go ahead and measure yours.Well now take our drawbar, slide it into the hitch, line up the hitch pin hole, and install our hitch pin. We can then put the clip on the other side of the pin, which will secure our ball mount to the vehicle in the drop position.In the drop position the measurement from the ball mount platform to the ground is 21-1/2 inches.
Hidden Hitch Ball Mount with 4 Inch Drop Review - 2012 Jeep Wrangler Unlimited
Today on our 2012 Jeep Wrangler Unlimited, well be test fitting the hidden hitch ball mount with 4-3/4 inch rise or 6 -inch drop rated at 6,000 pounds, part number 80240.Before we install our drawbar, well first need to get our hitch height measurement. To do this well measure from the top of the receiver tube to the ground. On this vehicle that measurement is 23-1/2 inches. Keep in mind this measurement can change due to tire size, hitch style or any other accessory that may affect vehicle ride height. Its a good idea to go ahead and measure yours.Well now slide the shank of the ball mount into the hitch, line up the hitch pin hole, and install our hitch pin. We can then put the clip on the other side securing our ball mount to the vehicle in the drop position.
Draw-Tite Ball Mount Review - 2012 Jeep Wrangler Unlimited
Today on our 2012 Jeep Wrangler Unlimited, well be test fitting the draw type ball mount with 3/4 inch rise or 2-inch drop rated as 6,000-pound, part number 2923.Before we install our drawbar, well first need to get our hitch height measurement. To do this well measure from the top of the receiver tube to the ground. On this vehicle that measurement is 23-1/2 inches. Keep in mind, this measurement can change due to tire size, hitch style or any other accessory that may affect vehicle ride height. Its a good idea to go ahead and measure yours.Well now go ahead and fit our drawbar into the hitch, line up the hitch pin hole and install our hitch pin with the pin and well put the clip on the other side which will secure our drawbar in the drop position. This drawbar does have a 2-inch strap, so the measurement from the ball mount platform to the ground will be 21-1/2 inches.
Thule Hitching Post Pro Hitch Bike Rack Review - 2012 Jeep Wrangler Unlimited
Today were working with a 2012 Jeep Wrangler Unlimited and were going to be test fitting the Thule hitching post pro hitch mounted bike carrier, part number TH934XTR. To mount our carrier to the vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up the hitch pin holes then thread in our anti-rattle bolt and tighten it down using a wrench. Next well go over a couple of clearance measurements. Weve got about 22 inches of ground clearance from the bottom of the bike rack to the ground, however keep in mind that our Jeep today does have aftermarket suspension and tires. Weve got about a of an inch of clearance between our aftermarket spare tire and the bike rack and overall weve added about nine inches of length.
Hollywood Racks SR2 Spare Tire Mount Bike Rack Review - 2012 Jeep Wrangler Unlimited
Today on this 2012 Jeep Wrangler Unlimited, we'll be test fitting the Hollywood Racks Spare Tire Rack, part number HRSR2. The first thing we need to do is remove the spare tire from the spare tire mount at the back of our Jeep, then well take our backing plate, fit it over the studs of our spare tire carrier, and reinstall the spare tire. With our spare tire installed, we'll select the proper adapter for the bike rack to accommodate the vehicle's spare tire, then we'll slide it in place over the mount then we'll take the appropriate length of the bolt to secure the carrier to the mount. Then we'll install our locking cover over that bolt. With our bike rack securely mounted, we can prepare to load a bike. We'll swing out the two bike rack arms and we'll also make sure that the rubber straps over the cradles closest to the vehicle are undone.
Husky Rear Floor Liner Review - 2012 Jeep Wrangler Unlimited
Today on our 2012 Jeep Wrangler Unlimited, well be test fitting the Husky Floor Liner in the second row, part number HL60551, black in color. First, well go ahead and remove the old or manufacturers floor mats. Now, were ready to install the Husky floor liners. Husky liners are custom molded to precisely fit the vehicle and stay in place. The shape, channels and moldings all work to keep dirt and debris contained in the liner and off of the carpeting. As you can see, its a one-piece liner that extends all the way from the driver to the passengers side.
Bestop HighRock Bumper Installation - 2012 Jeep Wrangler Unlimited
Today on our 2012 Jeep Wrangler Unlimited, were going to be installing the Bestop HighRock Narrow Front Bumper, part number B4293301. This will be in conjunction with the Bestop Tubular Grill Guard, part number B4291501. Our first step is going to be removing the lower rock guard. As you removed the lower rock guard, there will be a total of six fasteners. These are screw-in pushpin fasteners. Well need to screw out the center of the fastener and then remove the pushpin part.
WeatherTech Rear Floor Liner Review - 2012 Jeep Wrangler Unlimited
All right, today in this 2012 Jeep Wrangler Unlimited, we're going to do a test fit of WeatherTech floor liner and the second row. This will be part number WT441052. The WeatherTech liners are custom mold to precisely fit the vehicle and stay in place. The shape, the channels and the moldings all work to keep dirt and debris contained in the liner and not in your carpet. Now you see there's about a half inch edge all the way around the liner and also covers up part of the rails for the front seats and that over the center of the vehicle and back down to the other side of the Jeep. And these liners can be easily removed from vehicle and clean with just soap and water.
Trailer Hitch Installation - 2012 Jeep Wrangler Unlimited - Hidden Hitch
Today on our 2012 Jeep Wrangler Unlimited we'll be installing the Hidden Hitch, part number 87424. Alright, here are a couple of measurements that will assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the spare tire is 5-1/4 inches. From the top of the receiver tube to the ground gives us 19-1/2 inches of ground clearance. Now, lets go ahead and install the hitch. Alright, my first step is going to be lower the exhaust.
Trailer Hitch Installation - 2012 Jeep Wrangler Unlimited - Draw-Tite
Today on our 2012 Jeep Wrangler Unlimited we'll going to be installing the Draw-Tite Hitch, part number 75515. Alright, here are a couple of measurements that will assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the spare tire is 5-1/4 inches. From the top of the receiver tube to the ground gives us 19-1/2 inches of ground clearance. Now, lets go ahead and install the hitch. Alright, my first step is going to be lower the exhaust.
Thule Spare Me Spare Tire Mount Bike Rack Review - 2012 Jeep Wrangler Unlimited
Today in our 2012 Jeep Wrangler Unlimited we're going to test-fit the Thule Spare Me bike carrier. Part number TH963XTR. Our first step will be removing the spare tire . Next well take the mounting bracket for our carrier and fit it to the spare tire carrier bracket on the vehicle. Then we'll go ahead and reinstall the spare tire . As you're reinstalling the spare tire the center cap of the wheel will be pushed out by the carrier bracket.
Thule Apex 4 Swing Hitch Bike Rack Review - 2012 Jeep Wrangler Unlimited
Today on our 2012 Jeep Wrangler Unlimited were going to be test fitting the Thule Apex Swing 4 Bike Carrier for 2-inch Hitches, part number TH9027. Our vehicle is equipped with a 2-inch hitch and our bike rack is already preassembled. We can go ahead and slide the bike rack shank directly into the receiver tube lining up the integrated hitch pin lock with the hitch pin holes and the receiver tube. Then well use the hand knob to secure bike rack to the hitch. This is what our bike rack will look like when its in stored position. Next well go ahead and take a few measurements.
Thule Apex 4 Hitch Bike Rack Review - 2012 Jeep Wrangler Unlimited
Today on our 2012 Jeep Wrangler Unlimited were going to be test fitting the Thule Apex four bike carrier for inch and a quarter and two inch hitches, part number TH9025. With our vehicle already equipped with a two inch hitch and our bike rack already preassembled were ready to go ahead and slide the bike rack shank directly into the receiver tube of the hitch. Well line up the holes in the hitch with the integrated locking hitch pin on the bike rack shank. Then well use the hand knob to secure the bike rack to the vehicle. As you can see once the hand knob is tightened down it really secures the bike rack to the vehicle. This is what our bike rack will look like when its in its stored position.
Jeep Wrangler Unlimited Questions and Answers
- Spare Tire Lock for 2013 Jeep Wrangler
- If your spare tire has at least 3/4 inches of clearance behind it, and you have an available lug opening that passes through the carrier on the vehicle, the Deadbolt # 4324 would work very well for you.
The Master Lock spare tire lock, part # 262DAT would also be an option. The lock prevents access to the head of the nut or bolt that retains the spare tire to the carrier attached to the rear of the vehicle.
view full answer...
- Whispbar Roof Rack Recommendation for a 2013 Jeep Wrangler Unlimited
- The Whispbar installation kit, # WB-K324, is listed as a fit for a 2013 Jeep Wrangler Unlimited with a hard top. You will also need the feet and bars. For a streamlined OEM appearance I recommend the Whispbar Flush Bar Roof Rack # WB-S11. And for bars that stick out at the end instead of being integrated into the foot, go with # WB-S18.
view full answer...
- Roof Rack Weight Capacity for 2012 Jeep Wrangler Unlimited Sport Hardtop for Use with Cargo Carrier
- We offer a number of roof rack systems for use with your 2012 Jeep Wrangler Unlimited Sport Hardtop. These can be seen using the link provided.
The weight carrying capacity of these roof racks will vary, and may be limited by your Jeep roof weight load rating. I reviewed an online copy of the manual but it did not indicate the load capacity for the hard top. You will want to consult your owners manual to confirm that safe weight load rating, keeping in mind that the weight of the roof rack i
view full answer...
- What Soft Top Will Fit at 2012 Jeep Wrangler Unlimited Is Additional Overhead Storage Available
- If your 2012 Jeep Wrangler Unlimited has a removable hard top and an aftermarket soft top is an option then, I would recommend the Bestop Trektop NX # B5682335. This is one of our more popular products, and it features Bestop premium sailcloth, which compared to vinyl or denim is more durable. It reduces road noise, and is mildew and UV resistant. This system also offers a built-in fold-back sunroof, and the side and rear curtains are removable to allow for additional air flow. It is available i
view full answer...
- Will the Carr Hoop II Steps fit a 2013 Wrangler Unlimited
- Yes, I spoke with my contact at CARR and she confirmed that the Carr Custom-Fit Side Steps # CARR101241 that you referenced will work on your 2013 Jeep Wrangler Unlimited.
view full answer...
- Adding a 7-Way Trailer Connector to a 2012 Jeep Wrangler Unlimited
- If your 2012 Jeep Wrangler Unlimited came with a 4-Way you will need to use 4 and 7 way installation kit # ETBC7. This is a hardwire installation but it does come with everything you will need for the installation. I have included some links that will explain the ETBC7 installation for you.
If the trailer also has electric brakes you will need a brake controller to operate them. The ETBC7 comes with the wiring needed to install a brake controller but the controller itself is sold separately.
view full answer...
- Will a Thule Helium Aero Bike Rack Will Clear the Spare of a 2013 Jeep Wrangler Unlimited
- You will need to take one simple measurement to determine if you will have enough clearance to install a Thule Helium Aero 2 Bike Rack # TH9042 on your 2013 Jeep Wrangler Unlimited.
You will need to measure from the center of the hitch pin on the hitch of your vehicle out to the furthest point out on your spare tire to determine how much clearance you will need. The # TH9042 that you referenced has a distance of 10-3/4 inches from the center of the hitch pin hole to the nearest upright portio
view full answer...
- Pasts Needed to Flat Tow a 2013 Jeep Wrangler Unlimited with a Falcon 2 Tow Bar
- What is basically comes down to is how the winch is mounted. A lot of the winches for Jeeps require a different bumper or front guard that gets in the way and/or uses the same mounting locations as the base plates would. If you do not have an aftermarket bumper or guard and the winch is not using any of the same mounting locations as the base plates then it will most likely not be an issue.
Be sure to consult the Jeep owners manual for more information on flat towing it. In addition to the ba
view full answer...
- Will Hollywood Bike Carrier part # HR 1400 Clear the Spare Tire on a 2010 Jeep Wrangler Unlimited
- In order to conclude whether or not the Hollywood Bike Carrier part # HR1400 will clear your spare tire on your 2010 Jeep Wrangler some measurements need to be taken.
You will need a straight edge such as a yardstick or a dowel rod and a measuring tape.
Hold the dowel rod or yardstick vertically against the back of your spare tire, making sure that the end of the straight edge extends lower than your hitch pin hole. Use the tape measure to find the distance from the center of the hitch pi
view full answer...
- Step Bars for 2012 Jeep Wrangler Unlimited that are Lower than OEM Step Bars
- According to the folks at Carr, the OEM step bars you currently have would most likely interfere with the Carr steps. I am unaware of any longer brackets that would lower your bars, I would recommend you check with your Jeep dealer.
Your best bet would be to remove your existing steps and install the a set of # CARR101241 hoops. According to Carr, the step portion of the hoops would sit about 5-1/2 inches below the rocker panels. The steps are sold in sets of 2, for all four doors you would n
view full answer...
- Can TrailerMate Tow Bar Wiring # TM781124 and Trailer Wiring Harness #118416 be Used Together
- The TrailerMate # TM781124 and the Tow Ready # 118416 can indeed be used together.
However, if you are using a supplemental braking system in your Wrangler Unlimited, you will need to install diodes inline with the TrailerMate harness to prevent backfeeding into the RV wiring. In most cases, you will need two diodes like part # RM-690, one on the right turn/brake and one on the left turn/brake circuit, unless you are using a supplemental braking system that requires the RV running lights to b
view full answer...
- What Roof Racks Fit 2013 Jeep Wrangler Unlimited with Hard Top Roof
- Roof racks for your 2013 Jeep Wrangler Unlimited Hardtop are available from Yakima and Thule. I have included a link to our product page that shows all four available rack systems for your Jeep.
The main differences between the available racks are their crossbar spread (the distance between front and rear crossbars once mounted to your Wrangler) and the shapes of the crossbars themselves. A wider crossbar spread makes it easier to transport longer items. The wing-like aero shape crossbar offe
view full answer...
- Tow Bar Recommendation for a 2012 Jeep Wrangler JK
- The price difference between the Blue Ox Aladdin Tow Bar, # BX4325, and the Roadmaster Blackhawk 2 All Terrain Tow Bar, # RM-422, is basically due to the fact that the Blackhawk 2 is a heavy-duty steel tow bar designed to flat tow full-size trucks and SUVs. The Aladdin is a lightweight aluminum tow bar designed to tow mid-size vehicles like your 2012 Jeep Wrangler.
For your situation, I recommend using the Blue Ox Aladdin tow bar for a few reasons. First, to use a tow bar, you will need a se
view full answer...
- Parts Needed to Flat Tow a 2013 Jeep Wrangler Unlimited Behind a Motor Home
- From what I have found the 2013 Jeep Wrangler Unlimited does NOT need to have fuses pulled to flat tow it. This means you will not need a fuse bypass. Consult the owners manual to confirm this and for other specific information on flat towing your Jeep. If it does indicate you need to pull a fuse then you would need # TD705.
There are other items needed to flat tow your Jeep: base plates, tow bar, safety cables, lighting, and supplemental braking.
For base plates I recommend the Roadmaster
view full answer...
- Will the Rhode Gear Highway 4 Bike Rack Fit on 2012 Jeep Wrangler Unlimited With Factory Spare Tire
- The Rhode Gear Highway 4 Bike Rack, # RG8015221, measures 11 inches from the center of the hitch pin hole to the back of the upright bar. This bike rack should have enough clearance to clear the factory spare tire on your 2012 Jeep Wrangler Unlimited, but I recommend measuring just to be sure.
You will want to measure from the center of the hitch pin hole on your trailer hitch to the rear-most point of your spare tire (see photo). If that measurement is less than 11 inches, then this bike rac
view full answer...
- Spare Tire Cover for a 2013 Jeep Wrangler Sahara Unlimited with 225/70R18 Tires
- A 225/70-18 tire size will have a diameter of about 30-1/2 inches and a width of about 8.8 inches. Cover # 052963753875 will fit a tire with an outer diameter of 30 to 33 inches. It will be a little large on your tire but the elastic band will take up some of the slack and it should fit fine.
Another cover option is from Bestop, manufacturer of Jeep tops and other accessories. You could use # B6103035. This cover also has an elastic band for a snug fit. There is also black cover # B6103015 an
view full answer...
- Will the Yakima SwingDaddy Trailer Hitch Mount Bike Rack Clear Spare Tire on a 2010 Jeep Wrangler
- The Yakima SwingDaddy, # Y02422 measures 11 inches from the center of the hitch pin hole to the back of its upright bar. It will just clear your spare tire with 1 inch to spare. This rack would be a great choice for your Jeep if you are looking for total access to the rear of the vehicle. It will allow you to swing the rack off to the side while keeping the bikes loaded. I have included a video review for you.
If you want to go with a little more clearance then I recommend the Thule Vertex, #
view full answer...
- Tow Bar Recommendations for a Currie Towing Kit on a 2012 Jeep Wrangler Unlimited
- I spoke with my contact at Currie and he said an adapter should not be necessary when using their mounting kit # CE-9033JK with a Blue Ox tow bar. They do not, however, have any information regarding using their mounting kit with a Roadmaster tow bar, so we cannot recommend using your Falcon 2 tow bar with the Currie kit.
As such, I would recommend the Blue Ox Alpha tow Bar # BX7365. It has a weight capacity of 6500 lbs and comes with a 3-year warranty. Safety cables are included with this pr
view full answer...
- Will a Thule Evolution Cargo Box Fit on Rhino-Rack Elliptical Roof Rack Crossbars
- The mounting hardware for the Evolution cargo boxes is designed to fit around crossbars up to 3-1/4 inches wide. This will limit you to Thule square bars, AeroBlade bars, or Yakima round bars. The Rhino-Rack bars would be too wide for the box mounting hardware to fit. I have included a link to the roof rack options we have for the 2013 Jeep Wrangler Unlimited for you to view.
view full answer...
- Hitch Mounted bike Rack Recommendation for a 2013 Jeep Wrangler Unlimited with Access to Trunk
- For a bike rack that will give you full access to the rear cargo area of your 2013 Jeep Wrangler I would recommend the Thule Apex Swing 4 Bike Carrier # TH9027. This rack will have plenty of clearance between the spare tire of your vehicle and the upright bar of the rack and will give you complete access to the rear of your vehicle even with bikes loaded because the upright portion of the rack can swing away.
I attached a review video for this rack on a Wrangler very similar to yours for you
view full answer...
- Transporting 13.5-foot Kayak in High Winds Using Sportrack J-Stacker Kayak Carrier, Part # ABR511
- I spoke to my contact at Thule for any information to address your concern about the stability of your 13.5-foot kayak in the J-style carrier when driven in high winds. Although Thule does not specifically apply wind ratings to their kayak carriers, it was suggested that the J-style that you are using would likely be a best option.
After discussing your safety concerns with one of their technical staff we agreed that the simplest solution is the addition of supplementary tie-down straps. This
view full answer...
- Westin Tube Steps for a 2008 Jeep Wrangler Unlimited 4-Door
- Yes, the Westin tube steps, # 23-3295, will fit your 2008 Jeep Wrangler Unlimited, 4-door model. I have included a link to all of the steps that will fit your Jeep.
view full answer...
- Do Equal-i-zer Pins with Attached Thumb Clips Fit In Place of the Stock Pin and Clip
- You can use the Pins and Thumb Clips, # EQ95-01-9415, in place of the regular pins, # EQ95-01-9400, on your Equal-i-zer weight distribution system. Either style of pin will fit. The pins with the clips come in a 2-pack while the traditional pin with clip is sold in quantities of 1.
view full answer...
- Will Yakima DoubleDown 2 Bike Hitch Mount Rack, Part # Y02423, Clear Wrangler Oversize Spare Tire
- The Yakima DoubleDown 2 Bike Hitch Mounted Folding Rack, Part # Y02423, allows clearance of 11-1/2 inches from the center of the hitch pin hole to the back of the upright bar. If this will not allow enough clearance for your oversize spare tire you will need to choose an alternate rack, as this one cannot be used with a hitch extender.
The Swagman Titan 2 Bike Tilting Carrier for 1-1/4" and 2" Hitches, part # S63400, is a hanging-style carrier that provides 14-1/2 inches clearance between the
view full answer...
- Rooftop Cargo Carrier Recommendation for a 2012 Jeep Wrangler Unlimited Hardtop
- We offer many rooftop cargo carriers ranging from baskets to boxes and even bags. Before you load a cargo carrier on the roof of your 2012 Jeep Wrangler Unlimited, I would recommend installing a roof rack if you do not already have one.
If you do not already have a roof rack on your Jeep, then I would recommend the Thule roof rack, which consists of the 58 inch square load bars, # THLB58, and the Gutter Feet, # TH300. The feet of this roof rack will mount on the rain gutters on your vehicle
view full answer...
- Will North Carolina Tar Heels Hitch Cover # CTH9S Fit a 2011 Jeep Wrangler Unlimited
- The North Carolina hitch cover # CTH9S is designed to fit in 2 inch hitch openings. This will fit the hitch on your 2011 Jeep Wrangler Unlimited which has a 2 inch hitch. The cover also comes with some foam pads that will eliminate rattle between the cover and the hitch. The cover can be held in with a regular hitch pin and clip but to deter theft I recommend a locking hitch pin, # 7683.
view full answer...
- Are Carr Custom-Fit Side Steps Difficult to Install on a 2011 Jeep Rubicon
- The Carr Custom-Fit Side Steps, part # CARR121241, will fit your 2011 Jeep Rubicon. Installation requires a drill, a center punch, 5/16 inch and 1/8 inch drill bits, a pair of both 1/2 inch and 7/16 inch wrenches, a Phillips screwdriver and a pencil.
The assembly process consists of first attaching the mounting brackets to the cast aluminum steps using the supplied hardware (please note that not all hardware supplied will necessarily be needed for any given installation).
After you have de
view full answer...
- Is There Drilling Required to Install a Bestop Trektop NX on a 2013 Jeep Wrangler Unlimited
- You will not need to do any drilling to install the Bestop Trektop NX Soft Top # B5682335. I checked out the installation instructions and there is not any drilling required. I am going to send you a separate email that has the instructions for you to download and check out.
view full answer...
- Dimensions of Clear Film on Thule Replacement Clear Film for Thule Hullavator # 853-5481
- The Thule Replacement Clear Film for Thule Hullavator, part # 853-5481, is a sheet that has four pieces of clear film that is designed to peel off the sheet and be applied to the flanges on the Thule Hullavator bar mount. The Thule Hullavator is a rooftop kayak carrier. The size of each individual piece of clear film is 1-3/8 inch x 1-1/16 inch and is paper thin.
These pieces are applied to the bar mount to protect the cross bar of your vehicles roof rack when the Hullavator bar mount is atta
view full answer...
- Does the Trektop Soft Top Completely Roll Up on a 2012 Jeep Wrangler Unlimited Altitude Edition
- I spoke with my contact at Bestop and he informed me that the top that you will want is the Supertop NX, # B5472335. The Supertop NX allows you to fold back the top for a sunroof appearance and allows you to roll the entire soft top back to the spare tire for a topless look. As you mentioned, the rear windows will need to be unzipped to roll the rear portion back.
The Trektop Soft Top, # B5680535, that you referenced will not fold all the way back to the spare tire like you are looking for b
view full answer...
all Jeep Wrangler Unlimited questions
