Jeep Cherokee owners are most interested in these products
change vehicle
Blue Ox Base Plate Installation - 1997 Jeep Cherokee
1997 Jeep Cherokee. Were going to install part number BX1110. Start off the front bumper needs to be removed for access to the frame. We got to remove some coverings first. Well go ahead and remove the screws in the plastic center grille and the plastic moldings around the headlights. Well go ahead and set those aside.
Trailer Hitch Installation - 1999 Jeep Cherokee - Curt
Today on our 1999 Jeep Cherokee, we'll be installing the Curt Hitch, part number 13084. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch such as a ball mount, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/2 inches. From the top of the receiver tube opening to the ground is 15-3/4 inches. Now, let's go ahead with the installation.
Trailer Hitch Installation - 2001 Jeep Cherokee - Hidden Hitch
Today, on this 2001 Jeep Cherokee, were going to install part number 87591 from Hidden Hitch. All right, this is what the hitch will look like once its installed on the vehicle. Next, well go ahead and give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground is going to be 19 1/2 inches, from the center of the hitch pin hole to the edge of the bumper is going to be 3 3/4 inches.Now, Ill go ahead and show you how the hitch is installed. All right, our first step is to go ahead and start installing hardware on the driver side frame rail. Therell be three blocks and inaudible 00:00:35. Well start with those first.
Trailer Hitch Installation - 2001 Jeep Cherokee - Curt
Today, on this 2001 Jeep Cherokee, were going to install part number 13160 from Curt. All right, this is what the hitch will look like once its installed on the vehicle. Next, well give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 20 inches and from the center of the hitch pin hole to the edge of the bumper will about 3 inches.Now, Ill go ahead and show you how the hitch is installed. Now, well hold the block up to the frame underneath to show how it should be oriented when its inside the frame. All right, now we can go ahead and install the hardware that goes into the frame of the vehicle.
Trailer Hitch Installation - 2000 Jeep Cherokee
Today on this 2000 Jeep Cherokee we're going to installing the Hidden Hitch, part number 87591. Here are a couple of measurements that will assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost point of the bumper is 3-1/2 inches. From the top of the receiver tube to the ground is 18 inches. This will assist you with selecting accessories such as a draw bar, a bike rack, or a cargo carrier. Now, lets go ahead with the installation.
Trailer Hitch Installation - 2000 Jeep Cherokee - Draw-Tite
Today on our 2000 Jeep Cherokee, were gonna install a Draw-TIte Hitch part number 63260. Here are a couple of measurements that will assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost part of the bumper 3 inches. From the top of the receiver tube to the ground is 18 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier. Now lets go ahead with the installation.
Trailer Wiring Harness Installation - 2000 Jeep Cherokee
Today on its 2000 Jeep Cherokee Sport well be installing part number 118354 from Tow Ready. T-one Harness install inside the vehicle sort of back catch and get access to the Wire Harness. All right a wire harness is behind this panel right here. The normal is spare tire align this is the spare tire not here. So were going to remove the threshold so that way we can have room to remove panel here on the side.Our T-One connects on fit in between these two pieces. So, lets go ahead and disconnect them.
Trailer Hitch Installation - 2001 Jeep Cherokee
Today on this 2001 Jeep Cherokee we are going to be installing Curt hitch part number 13084. Before we get started with the hitch installation we are going to show you a couple of final installed dimensions that are going to help make choosing your hitch accessories a little bit easier. From the top of the receiver tube opening to the ground is going to measure 15 inches and from the center of the pin hole to clear the rear edge of the bumper is going to be about five inches. Now we will move on to our installation. 00:24
Trailer Hitch Installation - 1997 Jeep Cherokee
Today on this 1997 Jeep Cherokee, we are going to install part number 13084 from Curt. First we are going to show you what the hitch looks like on the vehicle. Next we are going to give you some measurements that will help you out in ing accessories such as a ball mount, a bicycle rack or a cargo carrier. First off, from the top of the receiver tube down to the ground is going to be 15-5/8 inches. And from the center of the hitch pin to the outside edge of the bumper is going to be 5 inches. Next we will go ahead and show you how it got installed. 0:28
Trailer Wiring Harness Installation - 1997 Jeep Cherokee
Today on this 1997 Jeep Cherokee we are going to install part number 118354 from Tow Ready. This T connector fits inside the vehicle on the driver side behind the tail light so what we need to do is get inside the vehicle to remove the spare tire and some interior panels. Now remove the fasteners for the spare tire bracket. Next we will remove the threshold panel. Now we need to remove the fasteners for this panel here. You do not have to take the whole panel loose but just for clarity we took it off. This is the connector right here that we have to disconnect and put our T connector into. It helps to pull this out a little bit to make easier working room. Push down this tab right here and it comes right apart and the T connector plugs right in between. Take everything and tuck it back into place. 01:42
Trailer Hitch Installation - 1991 Jeep Cherokee
Today on this 1991 Jeep Cherokee we will be installing Draw-Tite hitch part number 75054. This installation will also apply to Hidden Hitch part number 87591. Okay we are underneath the vehicle and the first thing we want to do is to figure out the configuration of the frame that you might have. The Cherokees have five different frame options. So you need to figure that out before we get started. The holes that we are going to be using here, this one, this one, this one, and this one. And those will be our four attaching points for the trailer hitch. And it will be the same here on the passenger side as well. You can see we have got the exhaust over here, but the hitch will go up and around that.
Trailer Hitch Installation - 2000 Jeep Cherokee
Today we are going to install part number 13084 from Curt, and we are going to install this on a 2000 Jeep Cherokee. First we will show you where the hitch installs on the vehicle. First off, it installs on four bolt holes: right here, here, here and on the very end of the frame. And there are three different configurations of this vehicle, depending on when and where it was made. On some vehicles, it is kind of rare, but they will actually have a plate inside of here with weld nuts inside there, so it would be easy just to screw bolts into it and be done. It is either going to be like this, where it is no bolt holes or no weld nuts in there or with weld nuts on the drivers side. And on the passengers side, it is going to go onto the same locations. And a lot of times, it will have that plate with all the weld nuts in it. It is more common to have it on this side than on the other side. Either way, this installation is the same you have still got these bolt holes. What you want to do is clean out these bolt holes, too, just to make sure you get rid of all the dirt and grime that get worked up in there. And also you will find this drivers side without any hardware on the inside, either. And then the last thing is that, usually, this bolt right here is notorious for being a real pain to get back out. It will make all kinds of creaking noises as you back it out. It is just the way it is made, I guess, because of the lock type that is in there, but it is a real pain to get out. But it will not break just take your time and keep working it out.
Trailer Hitch Installation - 1997 Jeep Cherokee
Jeeps are the original outdoor enthusiasts vehicle of choice. Now we have many SUVs but those Jeeps are still just fun to drive! A receiver hitch on your Jeep will allow you to tow a trailer, think boats or jet skis, use a cargo carrier for extra cargo room or use a hitch mounted bike rack. However you like to spend your down time a hitch will help make it more enjoyable. This video shows us installing a custom fit receiver on a Cherokee. The hitch was designed to make the process as easy as possible so no drilling is required. Take a minute to watch it, we are sure afterwards you will be calling to place your order
Jeep Cherokee Questions and Answers
- Thule AeroBlade Edge Roof Rack for a 2014 Jeep Grand Cherokee Limited
- We do have a Thule AeroBlade Edge roof rack that will fit your 2014 Jeep Grand Cherokee Limited, however the AeroBlade Edge Roof Rack, # TH7502-TH7502, that you referenced will fit raised OEM side rails only.
For the flush side rails on your Jeep, you will want the AeroBlade Edge Roof Rack, # TH7602-TH7602, along with the Fit Kit, # THKIT4019. You can add the Thule One-Key Locks, # TH544, to secure your roof rack to your Jeep when you are away from the vehicle.
view full answer...
- Installation Instructions for the Draw Tite Wiring Harness # 119175KIT
- Check out the link I attached that will take you to the installation instructions for the Draw Tite wiring harness # 119175KIT. I also attached a link to an install video that details this process as well. The vehicle may not be the same as your 1989 Jeep Cherokee, but the installation will be the same.
I will send you a .pdf of the instructions in a separate email also.
view full answer...
- Does the Air Dam on a 1998 Jeep Cherokee have to be Removed to Install a Front Mount Trailer Hitch
- The air dam does need to be trimmed (or removed) to install front mount trailer hitch # 65009. The skid shield, if present, would have to be removed. I have included a link to the installation instructions for this hitch so you can see the installation procedure.
view full answer...
- Recommended Trailer Hitch for 1997 Jeep Cherokee
- The Draw-Tite Class I receiver you mentioned, part # 24827 is a vehicle-specific item that will fit a 2005-2010 Scion tC only.
To see the various hitches available for a 1997 Jeep Cherokee, click the provided link. I would recommend the Curt Class III receiver, part # 13160. A Class III receiver will allow you to maximize the towing capacity of your Cherokee. The more common 2 inch receiver size will also allow you a better selection of hitch accessories like bike racks or cargo carriers, if
view full answer...
- Can a Front Mount Trailer Hitch be Used to Flat Tow a 1991 Jeep Cherokee
- A front mount trailer hitch like # 31084 can be used for a winch or for pushing around a trailer to get it in the right position but you can not use it to tow your 1991 Jeep Cherokee. You would not be able to turn properly with a single attachment point at the center of a 4 wheeled vehicle.
To flat tow a vehicle you will need a special attachment called base plates, a tow bar, safety cables, lighting, and supplemental braking. Base plates and a front mount hitch cannot both be installed at th
view full answer...
- Will the Yakima RocketBox Pro 11 Cargo Box Fit on a 1998 Jeep Cherokee Sport
- The Yakima RocketBox Pro 11 Cargo Box, # Y07193, will fit on your 1998 Jeep Cherokee Sport if you have a Yakima roof rack. According to Yakima, the RocketBox cargo boxes will not fit on the factory roof rack of the Jeep Cherokee.
There are a few different Yakima roof racks that will fit on your Jeep, but choosing the correct rack will depend on what you currently have on your roof. If you have the factory roof tracks that run front to back, you can use the Yakima Control Tower Roof Rack. This
view full answer...
- Ski and Snowboard Carrying Options for 2001 Jeep Cherokee
- Although we do not offer a ski rack solution that will install directly to the side rails of your Cherokee, you can still carry skis or snowboards if crossbars are added using the following parts:
Yakima 48 inch crossbars, part # Y00408 (includes 2)
Yakima Control Towers, part # Y00214 (includes 2)
You will also need two of the Yakima Landing Pad Kits, part # Y00222. Each Kit includes 2 pads, but you will need 4, so order two of the part numbers.
Once the crossbars are in place, Yakima o
view full answer...
- Incorrect Blinker Function With Optronics LED Trailer Light, Part # STL53RCB, on 1994 Jeep Cherokee
- I note that you have also purchased an appropriate T-connector harness, part # C55330, to adapt these LED trailer lights to your Jeep Cherokee (which has a 3-wire lighting system) along with the appropriate load resistors.
Based on your description of the problem, I suspect a bad ground connection.
Check that the white ground wire with ring terminal from your pigtail lead is tightly secured to a clean (and preferably bare) metal surface. You might try sanding off any paint if the ground
view full answer...
- Shank Measurements For MaxxTow Wheelchair Carriers # MT70260, # MT70106
- For the MaxxTow Wheelchair Carriers # MT70260 and # MT70106, the length of the shank from the center of the pinhole to the closest edge of the carrier when in the folded position is 7-1/2 inches. Just to be sure, I contacted my source at MaxxTow and he confirmed this measurement.
view full answer...
- Availability of Trailer Wiring Harness for 1992 Jeep Comanche
- My Contact at Curt Manufacturing tells me that the # C55330 should be the correct trailer harness for your Comanche given that it is based on the Cherokee, but did not have enough specific information to be 100 percent certain.
Your best bet would be to locate the connector that your existing harness plugs into, and compare it to the T portion of the # C55330 shown in the photo I have provided. If the connectors look alike, the C55330 should work fine for you. If not, using a universal conver
view full answer...
- Will the Thule Passage 2 Bike Carrier # TH982XT Fit on a Jeep Cherokee
- The Thule Passage 2 Bike Carrier, # TH910XT, will fit on your Jeep Cherokee as long as it is newer than 1991. To install this bike rack you will place the top clips in the gap at the top of the rear hatch and the bottom clips on the bottom edge of the rear door. The lower arm of the carrier will rest above the license plate well. Please note that the rear wiper cannot be used when the carrier is mounted.
If you plan on carrying any womens, childrens or alternative bike frames, then I also rec
view full answer...
- Tow Ready Trailer Wiring Harness for a 1992 Jeep Cherokee
- For the 1992 Jeep Cherokee you can use trailer wiring harness # 118330. I have included a link to the installation instructions for you to view.
The harness that you have referenced, # 118354, is deigned to fit the 1997 to 2001 Jeep Cherokee but will not fit a 1992.
view full answer...
- Will Curt Roof Mount Cargo Basket Fit a 1997 Jeep Cherokee Sport XJ
- For a roof mount basket, you will need to have crossbars that run from side to side on the roof. To determine if the Curt roof basket, # C18115, will fit your 1997 Jeep Cherokee you will need to measure the bars width and the center to center distance between them.
The Curt basket fits on crossbars that are no wider than 3 inches and a bar spread of at least 15 inches. I have included a link to the basket instructions for you.
If you need to add crossbars I have included a link to the roof
view full answer...
- Base Plate Kit Recommendation for a 1996 Jeep Cherokee Sport with Tow Hooks
- The Roadmaster XL Base Plate Kit, # 1418-1, will work on your 1996 Jeep Cherokee and it is compatible with your Falcon 2 tow bar. The only additional item that you may need to use the base plates with your Falcon 2 tow bar is the Roadmaster Quick Disconnect Tow Bar Base Assembly, # 910021-00, if you do not already have one with your tow bar.
When installing these base plates, you will need to remove the tow hooks and the front bumper. Once installation is complete, you will replace the front
view full answer...
- Size of the Bolts that Come with the Hidden Hitch for the 2001 Jeep Cherokee
- The bolts that secure the Hidden Hitch Trailer Hitch # 87601 that you referenced are M12 x 1.75 x 45 mm CL10.9.
You should note that if your vehicle is equipped with reinforcement bars you will reuse the existing M12 fasteners.
Check out the installation instructions for this product that I attached also.
view full answer...
- Roadmaster Base Plate Recommendation for a 1998 Jeep Grand Cherokee
- Yes, the Roadmaster Classic Base Plate Kit # 1411-1 that you referenced is confirmed to fit your 1998 Jeep Grand Cherokee. To safely flat tow a vehicle there are several components needed. The first is the base plate kit which we have already picked out.
Next, you will need a set of tow bars. For that I recommend you get a RoadMaster Sterling All Terrain Tow Bar # RM-585. This tow bar comes with quick-disconnects, safety cables and wiring run for lighting. I attached installation instructions
view full answer...
- Roof Mounted cargo Basket Recommendations for a 1999 Jeep Cherokee Sport
- First, if you have the factory installed crossbars that run side to side on the roof, then the Thule MOAB, # TH690, is a direct fit. You could tie down a canoe or kayak directly to the basket without additional parts. This basket has a capacity of 165 pounds. However, if the roof rack or roof is rated lower then you will have to go by the lower rating.
To determine if the Rola basket, # 59504, will fit, there are some measurement you will need to take. First, measure the thickness of the bars
view full answer...
- Thule Stacker Kayak Carrier Recommendation for a 2000 Jeep Cherokee
- Since one of your kayaks is over 10 feet long you will need to get the Thule Hull-A-Port Pro Folding J-Style Rooftop Kayak Carrier # TH835PRO.
If you have a 2000 Jeep Grand Cherokee the factory cross bars will be adequate for you to attach the # TH835PRO to, if you have a 2000 Jeep Cherokee then you will first need an aftermarket roof rack additionally. Check out the link I attached that shows all the different racks that would work for you.
view full answer...
- Adding a 7-Way Trailer Connector and Brake Controller to a 1991 Jeep Cherokee Sport
- To add a 7-Way and wiring for a brake controller you will need the 4 and 7 way installation kit, # ETBC7. This kit provides you with the 7-Way and all the parts needed to wire your 1991 Jeep Cherokee. For a brake controller, I recommend the Tekonsha P2, # 90885.
I have included some installation instructions and a video that should help you with the installation of the ETBC7 and brake controller.
Basically, you will plug in the 4-Way you have into the back of the ETBC7. The white wire wil
view full answer...
- What is the Length of the Hose In the Derale Engine Oil Cooler Kit # D15602.
- The hose that is included with the Derale Stacked-Plate Engine Oil Cooler Kit, # D15602, is 10 ft long and has a 1/2 inch inner diameter.
We sell 1/2 inch inner diameter hoses individually as well if you need additional length. I have included a link to all of the hoses we sell for you.
view full answer...
- What Size Holes Need to be Drilled to Install Curt Front Hitch # 31084 and Draw-Tite # 65009
- For the Curt front mount trailer hitch, you will need to drill two 17/32 inch holes in the bottom of the frame rails. There should not be anything inside the frame rail so you should not worry about punching through with the drill. Take a look at the instructions link I have provided for you.
The Draw-Tite hitch # 65009 requires a 1/2 inch hole. I have included a link to the instructions for it as well.
view full answer...
- What is the Difficulty Level for Installing the Curt Trailer Hitch on a 1998 Jeep Cherokee
- We do have an installation video of our Hidden Hitch Trailer Hitch being installed on a 1997 Jeep Cherokee, but at this time I do not have a video of the Curt Class III Trailer Hitch, # 13160, being installed on a 1998 Jeep Cherokee. The vehicle and hitch in our video are slightly different, but the installation process will be the exact same as your Curt hitch and 1998 Jeep Cherokee.
The estimated install time for the Curt trailer hitch, # 13160, is a time that the manufacturer feels it wil
view full answer...
- Blue Ox Tow Bar and Base Plate Kit Recommendation for a 1988 Jeep Cherokee
- The correct base plate kit for your 1988 Jeep Cherokee that would work with the Blue Ox Alpha Tow Bar # BX7365 would be the Blue Ox Base Plate Kit # BX1110. With the proper tools this install would be something that you could do yourself. I will email you a copy of the installation instructions for this product for you to check out.
The # BX1110 is also confirmed to work with the # BX7365.
I did some checking and it looks like if your vehicle is 4WD then your vehicle is tow-able as-is. If
view full answer...
- Availability of Replacement Drawbars for Roadmaster Base Plate Kit # 1418-1 on 1998 Jeep Cherokee
- The replacement draw bars are available, as part # C000098 for the passenger side and # C000097 for the drivers side.
You can order them online, or by calling our Customer Service folks at 800-298-8924. You will need to allow some extra time for fabrication and shipping.
view full answer...
- Does 1996 Jeep Cherokee with Factory Tow Package Need a Trailer Tail Light Converter # 118330
- If the trailer connector you currently have is factory installed, you should be good to go. The signals going to that connector should already be converted, so you will not need # 118330, which would be needed if the vehicle was never equipped with a trailer connector. It sounds as if you have a 7-way trailer connector, like part # PK11893 that has 6 blade-type pins with a contact in the center.
You can use a circuit tester like part # 40376 to test the connector to ensure it is functional.
view full answer...
- Wiring Tow Vehicle to Work With Tekonsha Prodigy RF # 90250
- You are pretty much on the right track. You will indeed need a 4-pole to 7-way adapter like part # 37185. In addition to the lighting functions provided by the 4-pole, you will also need to run the black 12-V power wire from the adapter to the positive battery terminal via a 40 amp circuit breaker like part # 9510. A length of 10 gauge wire like part 10-1-1 (sold by the foot) would also be needed. The power wire is needed to supply the power module mounted on the trailer. The white wire with the
view full answer...
- Are there Rubber Nibs on the Back of the Highland All Weather Floor Mats
- I went out the the warehouse and checked the Highland All Weather Floor Mats to see if there are rubber nubs on the back to help keep the mats from moving under foot and found that the rear protion of the mats do have nubs.
The front portion of the mats have a rubber cross hatch pattern to ease installation and help keep the mats from moving.
I took a photo of the mats for you to see while I was at it, see link.
view full answer...
- Installation Instructions for Curt Trailer Hitch 13084 on a 1997 Jeep Cherokee Country Edition
- If you are talking about the skid shield, it will need to be removed or loosened for hitch installation. On the 1997 Jeep Cherokee, there are 4 possible vehicle types in terms of trailer hitch installation. The instructions for the Curt trailer hitch, # 13084, covers each type. I have included a link to the installation instructions for you to review. I have also included a link to a video showing a typical installation.
If you plan on doing some towing, I recommend the etrailer ball mount ki
view full answer...
- Base Plates, Tow Bar, and Accessories to Flat Tow a 1991 Jeep Cherokee
- I am not sure what type of base plate system you have but if you can send me pictures I may be able to determine if anything we have will fit. What I recommend is to install a completely new system so you know that it is compatible with a tow bar and you will get all new parts and will not have to worry about the condition of the system. You will also want to consult the vehicle owners manual for the proper procedure for towing the vehicle.
For your 1991 jeep Cherokee you can use # 1418-1. Th
view full answer...
- Will the Browning Universal-Fit Bucket Seat Cover Fit a 1999 Jeep Grand Cherokee
- The Browning Universal-Fit Bucket Seat Cover, # SPGBSC4404, is a universal fit item designed to fit most truck, car, and SUV bucket seats. It does have some elasticity so it will stretch though it the headrest is set very high, you may have installation problems. If your seats have a seat belt that is integrated into the seats, the cover will not fit.
view full answer...
all Jeep Cherokee questions
