Select Your Vehicle
view cartView Cart
Only 18 Hours 55 Minutes Remaining

Hyundai Santa Fe owners are most interested in these products

change vehicle






Hyundai Santa Fe Videos

Trailer Hitch Installation - 2014 Hyundai Santa Fe - Curt

Today, in this 2014 Hyundai Santa Fe Limited, we're going to install part number C13153 from Curt. This is what the hitch looks like when it's installed on the Santa Fe. Next, we'll use the measurements to help you out in selecting some accessories, such as a ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about 16". From the center of the hitch pin hole to the edge of the bumper will be about 4". Now we'll go ahead and show you how the hitch is installed. First thing we need to do is go ahead and get underneath the vehicle. We'll go ahead and remove the panel that's at the bottom of the bumper and in the center.



Trailer Wiring Harness Installation - 2014 Hyundai Santa Fe

All right, today on 2014 Hyundai Santa Fe Limited, we're going to install part number 118269 from Tow Ready. First thing we need to do is find a tow prep package. It's located behind the rear wheel on the driver's side. These two parts here. To get things ready all we got to do is go ahead remove the caps. There's a small tab right here to push in.



Trailer Brake Controller Installation - 2014 Hyundai Santa Fe

All right, today, on this 2014 Hyundai Santa Fe Limited, we are going to install part number 90195. This is Tekonsha Prodigy p3 trailer brake controller. Now to help us with our install, we will also be using part number ETZC7. We are going to start off by making access from the inside to the outside. We will go ahead and drill a pilot hole first on the fire wall from the inside. We will drill a 1/4" pilot hole, now go ahead and use our hole saw, it doesn't really matter what size, just enough to get us some working room so we don't tear up the carpet as much. Now we will be using a step bit to enlarge our hole. We've got our hole drilled out, we will go ahead and mount our circuit breakers.





Thule Vertex 4 Hitch Bike Rack Review - 2005 Hyundai Santa Fe

Today on our 2005 Hyundai Santa Fe, we'll be test fitting the Thule Vertex 4-Bike Carrier part number TH9029. We'll begin our test fit by sliding the shank of the carrier into the opening of the hitch lining up our pin holes and install and tighten down our anti-rattle bolt. Now with our Thule Vertex secured to our Santa Fe, we'll go over a few clearance measures to see how the 2 fit together. We have about 15 inches of ground clearance. The closest part of the carrier to the closest part of our Santa Fe is here at the rear bumper is about 3-1/2 inches away. With the cradle arms down, we've added about 12-1/2 inches to the overall length of our Santa Fe.



Thule Hitching Post Pro Hitch Bike Rack Review - 2005 Hyundai Santa Fe

Today, on our 2005 Hyundai Santa Fe, we'll be test fitting the Thule Hitching Post Pro, part number TH934XTR. We'll begin our test fit by sliding the shank of the carrier into the opening of the hitch and install and tighten down the anti-rattle bolt. Now, with the Hitching Post Pro secured to our Santa Fe, we'll go over a few clearance measurements to see how the 2 fit together. We have about 15 inches of ground clearance to the rear. The closest part of the carrier to the closest part of our Santa Fe is here at the rear bumper about 7 inches away, and with the cradle arms down, we've added about 17 inches to the overall length of our vehicle. We'll now pull the gold pin at the top of the mast to swing the cradle arms out, and with the cradle arms out, we've added about 38 inches to the overall length of our vehicle. To access the cargo area, we'll pull the gold pin at the base of the carrier to tilt the mast down.



Thule Apex 4 Swing Hitch Bike Rack Review - 2005 Hyundai Santa Fe

Today on our 2005 Hyundai Santa Fe, we'll be test fitting the Thule Apex Swing 4-Bike Carrier part number TH9027. We'll begin our test fit by sliding the shank of the carrier into the opening of the hitch lining up our pin holes allowing the integrated hitch pin to fall into place and we'll then turn the black knob at the base of the carrier to engage the anti-rattle device. Now with our Apex Swing secured to our Santa Fe, we'll go over a few clearance measurements to see how the 2 fit together. We have about 14 inches of ground clearance at the rear. The closest part of the carrier to the closest part of our Santa Fe is here at the rear bumper about 2 inches away. Withthe cradle arms folded down, we've added about 12 inches to the overall length of our vehicle.



Thule Apex 4 Hitch Bike Rack Review - 2005 Hyundai Santa Fe

Speaker: Today on our 2005 Hyundai Santa Fe we'll be test fitting a Thule Apex 4-Bike Carrier Part No. TH9025. We'll begin our test fit by sliding the shank over the carrier into the opening of the hitch lining up our pinholes allowing the integrated hitch pin to fall into place and we'll then turn the black knob at the base of the carrier to engage the anti-roll device. With our Thule Apex secured with our Santa Fe we'll go over a few clearance measurements to see how the two fit together. We have about 16 inches of ground clearance. Closest part of the carrier to the closest part of our Santa Fe is here at the rear bumper about 2 inches away and we've added about 13 inches to the overall length of the vehicle. We'll now lift the gray lever at the top of the mast to swing the cradle arms out and with the cradle arms out we've added about 36 inches to the overall length of our vehicle. To access the cargo area we'll lift up the gray lever at the base of the carrier to tilt the mast down. Now as you can see we can easily gain access to the rear hatch of our Santa Fe. To load the bike we'll make sure the mast is in its upright position. We'll undo the cradle straps, place our bike into the frame cradles and secure with the straps. That complete today's test fit for the Thule Apex 4-Bike Carrier Part No.



Firestone Coil-Rite Air Helper Springs Installation - 2005 Hyundai Santa Fe

Today on this 2005 Hyundai Santa Fe were going to install part number f4170 from Firestone. First step is to go ahead and remove the original jounce bumpers. Theyre located inside the spring. Well go ahead and pry those out of our way. Now in the cup where the jounce stop was were going to have to drill an access hole for an air line. Well drill out a 1/8inch pilot hole first, and then well go ahead and drill it out to 5/16.



Yakima HighLite 2 Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Yakima Highlite aluminum two bike carrier, part number Y02438. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up our pin holes, insert the attached pin into the pin hole and turn the black knob to engage our anti-rattle bolt. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 11 1/2 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier at the bottom of the bumper is about 4 inches. With the cradle arms folded down we've added about 10 inches to the overall length of the vehicle measured at the bumper.



Yakima DoubleDown Ace Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Yakima Doubledown Ace four bike carrier, part number Y02451. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up our pin holes, insert the attached pin into the pin hole and turn the black knob to engage our anti-rattle bolt. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 11 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier at the bottom of the bumper is about 5 inches. With the cradle arms folded down we've added about 12 inches to the overall length of the vehicle measured at the bumper.



Thule Vertex 4 Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Thule Vertex four bike carrier, part number TH9029. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up the pin holes, thread our anti-rattle bolt through the pin holes and tighten with a wrench. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 12 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier is about 3 inch at the bottom of the bumper. With the cradle arms folded down we've added about 12 inches to the overall length of the vehicle measured at the bumper.



Thule Apex 4 Swing Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Thule Apex swing, four bike carrier, part number TH9027. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up our pin holes, insert the spring loaded pin through the pin hole and tighten down the knob to engage our anti-rattle device. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 12 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier at the anti-rattle knob is about 1 inch. With the cradle arms folded down we've added about 10 inches to the overall length of the vehicle measured at the bumper.



Thule Apex 4 Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Thule Apex four bike carrier, part number TH9025. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up the pin holes, insert the spring loaded pin into the pin hole and turn the black knob to engage our anti-rattle device. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 12 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier at the anti-rattle knob is about 1 inch. With the cradle arms folded down we've added about 13 inches to the overall length of the vehicle measured at the bumper.



Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Swagman XTC 2 two bike carrier, part number S64670. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up the pin holes, thread our anti-rattle bolt through the pin holes and tighten with a wrench. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 12 inches of ground clearance. Closest part of the carrier to the closest part of the vehicle here at the rear bumper is about 8 inches. We've added about 24 inches to the overall length of the vehicle measured from the rear bumper.



SportRack Escape 3 Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Sportrack Escape three bike carrier, part number A30403. Now to begin our test fit we'll slide the bike rack shank into the opening of the hitch, line up our pin holes, thread our anti-rattle bolt through the pin holes and tighten it with a wrench. Now we'll go over some clearance measurements to see how the carrier and this vehicle will fit together. There is about 12 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier is about 5 inch. With the cradle arms folded down we've added about 12 inches to the overall length of the vehicle measured at the bumper.



Thule Parkway 2 Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with the 2009 Hyundai Santa Fe, and were going to be test fitting the Thule Parkway Two hitch mounted bike carrier, part number TH958. To mount the carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up the hitch pin hole, thread in our anti-rattle bolt and tighten it down with a wrench. Next we want to check for rear vehicle access. Well remove the pin at the base of the bike rack and tilt it down. We want to make sure that we can still open the cargo door completely and access the cargo area of our Santa Fe, even with the bike rack installed.



Thule Doubletrack Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with a 2009 Hyundai Santa Fe, and were going to be test fitting the Thule Doubletrack hitch mounted bike carrier, part number TH990XT. To mount the carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch, making sure we line up the hitch pin holes. Then well thread in our anti-rattle bolt and tighten it down using a wrench. Next well go over a few clearance measurements. Weve got about 10 inches of ground clearance from the bottom of the bike rack to the ground. Weve got about two inches of clearance from the closest part of the vehicle to the closest part of the bike rack.



Pro Series Eclipse 4 Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today on our 2009 Hyundai Santa Fe were going to be test fitting the Pro Series Eclipse Four hitch mounted bike carrier, part number 63124. To mount our carrier to the vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well then thread in our anti-rattle bolt and tighten it down using a wrench. Next we want to check for rear vehicle access. Well remove the pin at the base of the bike rack and tilt it down. We just want to make sure that we can fully open our cargo door and access the area, even with the bike rack installed.



Yakima StickUp 2 Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with a 2009 Hyundai Santa Fe, and were going to be test fitting a Yakima Stickup Two hitch mounted bike carrier, part number Y02420. To mount this carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up our hitch pin hole and thread in our anti-rattle bolt, tightening it down with a wrench. Next well go some clearance measurements. Weve got about 11 inches of ground clearance from the bottom of the bike rack to the ground. Weve got about a half inch of clearance between the closest part of the bike rack and the carrier.



Thule Vertex 4 Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with the 2009 Hyundai Santa Fe, and were going to be test fitting the Thule Vertex Four hitch mounted bike carrier, part number TH9029. To mount our carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up the hitch pin hole, thread in our anti-rattle bolt and then tighten it down with a wrench. Next we want to check for rear vehicle access. Well grab the switch at the base of the bike rack and tilt it down. We want to make sure that we can open the cargo door completely and still access the area, even with the bike rack installed.



Thule Hitching Post Pro Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with the 2009 Hyundai Santa Fe, and were going to be test fitting the Thule Hitching Post hitch mounted bike carrier, part number TH934XTR. To mount this bike rack to our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well feed on our anti-rattle bolt and tighten it down with a wrench. Next we want to check for rear vehicle access. Well remove the pin at the base of the bike rack and tilt it down. We want to make sure that we can open our cargo door completely and access our cargo area.



Thule Apex 4 Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with the 2009 Hyundai Santa Fe, and were going to be test fitting the Thule Apex Four hitch mounted bike carrier. To mount our carrier to the vehicle well make sure that we pull over the automatic hitch pin, slide the shank into the receiver tube and let the hitch pin secure on its own. Then well tighten down the bike using the hand knob at the base to activate the anti-rattle device. Next we want to check for rear vehicle access. Well grab the switch at the base of the bike rack and tilt it down. We want to make sure that we can open the cargo door all the way and access our cargo area, even with the rack installed.



Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today on our 2009 Hyundai Santa Fe, we're going to be test fitting the Swagman XTC 2 Hitch Mounted Bike Carrier, Part Number S64670. To mount the carrier to our vehicle, we'll insert the shank in the carrier into the receiver tube of the hitch. We'll make sure to line up the hitch pin hole and thread in our anti-rattle bolt. We'll then tighten it down using a wrench. With the bike rack secure, we want to check some clearance measurements. We've got about 11-1/2 inches of ground clearance from the bottom of our bike rack to the ground.



Surco Hitch Cargo Carrier Review - 2009 Hyundai Santa Fe

Today were working with a 2009 Hyundai Santa Fe and were going to be test fitting Surcos 24 inch by 60 inch cargo carrier, part number 52018. To mount the carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up the hitch pin holes and secure the carrier with the pin and clip. Next we want to go over some clearance measurements. Weve got about 10 inches of ground clearance from the bottom of the carrier to the ground at the rear of our carrier. Overall weve added about 25 inches of length to the rear of the vehicle.



SportRack EZ Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today, we're working with the 2009 Hyundai Santa Fe and we're going to be test fitting the SportRack 2 Hitch Mounted Bike Carrier, Part Number A30901.To mount the carrier to the vehicle, we'll insert the shank of the carrier in the receiver tube with the hitch. We'll make sure to line up the hitch pinholes then insert our anti-rattle bolt, and tighten it with a wrench. Next, we'll go over a few clearance measurements. We've got about 11-1/2 inches of ground clearance from the bottom of the bike rack to the ground. We have about 6 inches of clearance between the closest part of the bike rack and the closest part of the vehicle. Overall, we've added about 23 inches of additional length to the rear of the vehicle.



Pro Series Q-Slot Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today on our 2009 Hyundai Santa Fe, we're going to be test fitting the Pro Series Q Slot Hitch Mounted Bike Carrier, Part Number PS63134. To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of our hitch. We'll make sure to line up the hitch pinhole and then we'll secure the rack with the pin and clip. Next, we'll go over some clearance measurements. We've got about 11-1/2 inches of ground clearance from the bottom of the bike rack to the ground. We've got about 5-1/2 inches of clearance between the closest part of our bike rack and the closest part of our vehicle.



Trailer Hitch Installation - 2012 Hyundai Santa Fe - Hidden Hitch

Today on our 2012 Hyundai Santa Fe we'll be installing Hidden Hitch, part number 87574. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 4 inches. From the top of the inside of the receiver tube opening to the ground is 12 3/4 inches. This will assist you when selecting accessories such as a ball mount, a bike rack, or a cargo carrier.



Trailer Hitch Installation - 2012 Hyundai Santa Fe - Draw-Tite

Today on our 2012 Hyundai Santa Fe we'll be installing the Draw-Tite hitch, part number 75684. This is what our hitch will look like once it's installed. Next we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is 4 inches. From the top of the inside of the receiver tube opening to the ground is 12 3/4 inches. This will assist you when selecting accessories such as a ball mount, a bike rack, or a cargo carrier.



Trailer Hitch Installation - 2012 Hyundai Santa Fe - Hidden Hitch

Today on our 2012 Hyundai Santa Fe, we'll be installing Hidden Hitch part number 90212. Next we'll go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3 1/2 inches. From the top of the inside of the receiver tube opening to the ground is 13 inches. This will assist you with accessories such as a bike rack or cargo carrier. First before we install the hitch, we'll go ahead and point out the attachment points.



Trailer Hitch Installation - 2012 Hyundai Santa Fe - Draw-Tite

Today on our 2012 Hyundai Santa Fe well be installing the Draw Tite hitch, part number 36511. Next well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is three and a half inches. From the top of the inside of the receiver tube opening to the ground is 13 inches. This will assist you with selecting accessories such as a bike rack or cargo carrier. First before we install the hitch well go ahead and point out the attachment points.



Pro Series Q-Slot Hitch Bike Rack Review - 2008 Hyundai Santa Fe

Today on our 2008 Hyundai Santa Fe, well be test fitting part number PS63134. This is the Pro Series Q Slot Platform Style Two Bike Carrier for both 1-1/4 and 2-inch hitches. Now to begin our installation, using the included adaptor for the 2-inch hitch, well slide our bike rack shank into the hitch, line up the hitch pin hole and install our hitch pin. Well then put the safety pin on the other side of our hitch pin which will secure our bike rack to the vehicle. Well now go ahead and give you a few measurements. Our ground clearance at the back of the bike rack is 15 inches and from the closest point of the bike rack to the back of the vehicle is 6 inches.



Thule Hitching Post Pro Hitch Bike Rack Review - 2008 Hyundai Santa Fe

Today on our 2008 Hyundai Santa Fe, well be test fitting the Thule Hitching Post Folding and Titling 4 Bike Rack with Anti-Sway Cradles for both 1-1/4 and 2-inch hitches part number TH934XTR. Now to begin our test fit, well use the included adaptor for the 2-inch hitch. We can then slide our bike rack shank into the hitch, line up the hitch pin hole and install and tighten down our anti-rattle bolt. With our bolt tight, our bike rack is secure to the vehicle. Well now go ahead and give you a few measurements. Our ground clearance at the bike rack is 10-3/4 inches and from the closest point of the bike racks mast, to the back of the vehicle is 83/4 inches.



Rhode Gear Highway Hitch Bike Rack Review - 2008 Hyundai Santa Fe

Today on our 2008 Hyundai Santa Fe, well be test fitting the Rhode Gear Highway 2 Bike Carrier part number RG8015220. Now to begin our test fit, well slide our bike rack shank into the hitch, line up the hitch pin hole, and install and tighten down our anti-rattle bolt. With our bolt tight, our bike rack is secured to the vehicle. Well now go ahead and give you a few measurements. Our ground clearance at the bike rack is 10-1/2 inches, and from the closest point of the bike rack to the back of the vehicle is 5 inches. Well now go ahead and pull the pin at the bottle of the bike rack mast, to allow the mast to tilt down.



Rain-X Weatherbeater Wiper Blades Installation - 2013 Hyundai Santa Fe

Today in our 2013 Hyundai Santa Fe, well be installing the Rain-X Weatherbeater Windshield Wiper Blades. For the drivers side, 26-inch wiper blade part number RX300226. For the passengers side, we have 14-inch wiper blade part number RX30214. The Rain-X Weatherbeater Wiper Blades are perfect replacement wiper blades that provide ultimate visibility in wet weather. Itll meet or exceed the OEM standards. Its windshield hugging frame design with multiple pressure points can deliver a clean wipe.



Trailer Wiring Harness Installation - 2013 Hyundai Santa Fe

Today on our 2013 Hyundai Santa Fe, we'll be installing the Tow Ready, T-One Vehicle Wiring Harness, Part Number 118571. First, we'll open up the rear cargo door then we'll remove the two fasteners securing driver's side tail light housing. Next, we'll go ahead and remove the tail light housing by pulling backward towards the rear of the vehicle, popping it free from its alignment pins and fasteners underneath then we'll go ahead and press in the locking tab for the connector and remove the wiring from the tail light assembly. Next, we'll remove the rear bumper cover fastener securing here underneath the tail light assembly. We'll remove this so that we can pull out on it giving us more access to feeding our wires from underneath up into the tail light assembly area. Now, we have the driver's side tail light assembly remove, we'll go ahead and repeat the same process in the passenger side.



Thule Parkway 2 Hitch Bike Rack Review - 2008 Hyundai Santa Fe

Today on our 2008 Hyundai Santa Fe, we'll be test fitting Part Number TH958. This is the Thule Parkway 2 Bike Carrier. Now to begin our test fit, we'll slide our bike rack shank into the hitch, line up the hitch pinhole and install and tighten down the anti-rattle bolt. With the anti-rattle bolt tight, our bike rack is secured to the vehicle. We'll now go ahead and give you a few measurements. Our ground clearance at the bike rack is 11 inches and from the closest point of the bike rack mast to the back of the vehicle is 1-5/8 inches.



Trailer Hitch Installation - 2013 Hyundai Santa Fe - Curt

Today on our 2013 Hyundai Santa Fe well be installing the Curt hitch, part number C13134. Before we begin our install heres what the hitch looks like when its installed on the vehicle. Well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is five and a half inches. From the top of the inside of the receiver tube opening to the ground is 12 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier.



Trailer Hitch Installation - 2012 Hyundai Santa Fe - Curt

Today on our 2012 Hyundai Santa Fe well be installing the Curt hitch, part number C13073. This is what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is four and a half inches. From the top of the receiver tube to the ground is 15 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or a cargo carrier.



Trailer Wiring Harness Installation - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe well install the Tow Ready T1 Connector, part number 118258. First lets go ahead and identify the manufacturers plugs or towing port that well be plugging into. Here on the drivers side underneath the vehicle behind the rear axle or tire are the two ports that are built in by the manufacturer. Well be connecting into these ports, but first were going to go ahead and disconnect them from the vehicle, push the grommet back into the interior of the vehicle and feed them back into the cabin. Now with them disconnected and fed into the cabin well go ahead and get inside the vehicle. Were going to remove the two storage trays and the drivers side quarter panel.



WeatherTech Front Floor Liners Review - 2009 Hyundai Santa Fe

Today we'll be test fitting the WeatherTech Floor Liner in the front row part number WT440961 black in color for your 2009 Hyundai Santa Fe. This application is also available in tan, part number WT450961 or grey part number WT460961. First, we'll go ahead and remove the old or manufactured floor mats. Now we're ready to install the WeatherTech floor liners. With the liners installed you can see the contours and shapes that fit the vehicle's floor board. The WeatherTech floor liners are custom molded to precisely fit the vehicle and stay in place.



WeatherTech Rear Floor Liner Review - 2009 Hyundai Santa Fe

Today on our 2009 Hyundai Santa Fe we'll be test fitting the WeatherTech Floor Liner in the second row part number WT440962. This application is also available in tan, part number WT450962 or grey part number WT460962. First, we'll go ahead and remove the old or manufacturer floor mats. As you can see, this is a one piece liner. It extends all the way from driver to the passenger's side threshold. The WeatherTech floor liners are custom molded to stay in place.



WeatherTech Cargo Floor Liner Review - 2009 Hyundai Santa Fe

Today in our 2009 Hyundai Santa Fe well be test fitting the Weathertech Floor Liner in the rear cargo area part #WT40317, black in color. This application is also available in grey part #WT42317 or tan part #WT41317. Weathertech Liners are custom molded to precisely fit the vehicle and stay in place. The shape, channels, and molding all work to keep dirt and debris contained in the liner and off of the carpeting. As you can see here, this liner is custom molded to go around the wheel well cutouts and has a raised outer edge to contain the dirt and debris. One more great feature about the Weathertech Floor Liner is its easy to install.



Trailer Wiring Harness Installation - 2007 Hyundai Santa Fe

Today on our 2007 Hyundai Santa Fe, well be installing the Tow Ready T1 connector, part number 118415. To begin our installation well first remove the rear threshold and rear cargo tray. To do this well first remove the three screws securing the rear cargo tray. Then well take our trim tool or a flat bladed screw driver, get underneath the rear threshold and pop it free from its fasteners. Now we can go ahead and take the rear cargo tray out of the vehicle and set it aside for re-installation later. Next well go ahead and remove the access panel on both the driver and passenger side.



Yakima RocketBox Pro 14 Rooftop Cargo Box Review - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe well be test fitting part number Y07192. This is the Yakima RocketBox Pro 14 Rooftop Cargo Box. Now our vehicle is equipped with a factor roof rack system and weve already measured and set up our RocketBox to fit the crossbar spread so were ready to go ahead and fit it to the vehicle. Well begin by placing the box on top of the crossbars with the clamps just in front of the crossbars themselves. We can then go around to make sure all our clamps are opened up. With them opened up well simply slide the RocketBox back towards the back of the vehicle allowing the clamps to move underneath the crossbars.



SportRack Aero Roof Cargo Box Installation - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe well be test fitting the SportRack Aero XL Cargo Box part number A90275. Now to begin our test fit well simply place our box on top of our factory crossbars. Well then need to line up the holes in the floor of the SportRack Aero with the crossbars themselves. With that done we can take the included hardware and install it making sure that the clamps go around the crossbars on both the front and rear. With the wing nuts tight inside the cargo box our box is secured to the vehicle and were ready to load it up. And that completes our test fit of the SportRack Aero XL Cargo Box part number A90275 on our 2011 Hyundai Santa Fe..





Yakima ForkLift Roof Mounted Bike Rack Review - 2007 Hyundai Santa Fe

Today on our 2007 Hyundai Santa Fe, we're going to be test fitting the Yakima ForkLift Roof Mounted Bike Carrier, part number Y02098. Our Santa Fe already has a factory roof rack system on it, so well be installing the forklift directly to the factory crossbars. Well take the bike rack and place it up on top of our crossbars. We'll fit the front clamp around the front crossbar and use the wing nut and T-bolt to tighten it down. Then we'll slide our cover back into place and we'll move to the rear. We'll fit the rear clamp around the rear bar and again we'll use the T-bolt and wing nut to tighten that down.



Trailer Hitch Installation - 2011 Hyundai Santa Fe - Hidden Hitch

Today on our 2011 Hyundai Santa Fe, we're going to install Hidden Hitch, part number 90212. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3-1/4 inches. From the top of the receiver tube to the ground is 13 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier.



Trailer Hitch Installation - 2011 Hyundai Santa Fe - Draw-Tite

Today on our 2011 Hyundai Santa Fe, we're going to install the Draw-Tite Hitch, part number 36511. This is what our hitch will look once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 3-1/4 inches. From the top of the receiver tube to the ground is 13 inches. This will assist you in selecting accessories such as a drawbar, a bike rack, or a cargo carrier.



Yakima LoadWarrior Roof Cargo Basket Review - 2007 Hyundai Santa Fe

Today we have a 2007 Hyundai Santa Fe and were going to be test fitting the Yakima Loadwarrior Roof Mounted Cargo Basket part number Y07070. Our vehicles already equipped the factory installed roof rack so we setup our basket to fit the factory crossbars. Its probably a good idea to go ahead and remove the factory radio antenna from the vehicle to allow space for the cargo basket. Next, well place the cargo basket up on top of our factory crossbars. Well make sure that its centered from left to right and then well feed the clamps around the crossbars and tighten them down with the included hardware. With that, our baskets installed and were ready to load it up and hit the road.



Yakima FrontLoader Roof Bike Rack Review - 2007 Hyundai Santa Fe

Today on our 2007 Hyundai Santa Fe, we're going to be test fitting the Yakima FrontLoader Roof Mounted Bike Rack, part number Y02103. Our Santa Fe is equipped with a factory roof rack so we're going to mount our FrontLoader directly to that. To mount the FrontLoader, we'll lift it up and place it on top of our crossbars. We'll take the head of the bike and fit the front clamp around our front bar and we'll use the hand nut to tighten it down. In the rear, we'll fit the rear clamp around the bar and use the T-bolt and wing nut to tighten it down. Once we've done that, our bike rack is secured and we're ready to load up a bike.



Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2007 Hyundai Santa Fe

Today we have with us the 2007 Hyundai Santa Fe and were going to be test fitting the Thule Standup Paddleboard Taxi part number TH810. Our Santa Fe already has a full factory roof rack so well just mount the SUP Taxi directly to our factory crossbars. Well take the first half of our carrier and place it up on top of our crossbars. Well feed the Speed Link straps around our crossbar and use the hand knobs to tighten them down. Once we got the first half tightened down, well take the second half and put it over our rear bar. We just want to make sure that it lines up with the front half and again tighten down the Speed Link straps.



RockyMounts TieRod Roof Bike Rack Review - 2007 Hyundai Santa Fe

Today we have with us a 2007 Hyundai Santa Fe and were going to be test fitting the Rockymounts Tierod Roof Mounted Bike carrier part number RKY1014. Our vehicle already has a full factory roof rack so were ready to go ahead and mount our bike rack to the bars. To fit our bike rack, well place it on top of our bars and put the head of the rack on our front bar making sure its wrapped the rubber-coated steel strap on the bar. Well fit them back into the head and tighten them down with the Allen key. Once weve done that, we can reinstall the cover of the head of the bike rack. At the back of the bike rack, well take our rear clamp, fit it around the bar and use the included wing nut to tighten it down.



Trailer Hitch Installation - 2010 Hyundai Santa Fe - Hidden Hitch

Today on this 2010 Hyundai Santa Fe, were going to install part number 85754 from Hidden Hitch. This is what the hitch looks like once installed on the vehicle. Next well go ahead and give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pinhole to outside edge of the bumper is going to be 3 inches and from the top of the receiver opening down to the ground is going to be 13 inches. Now well go ahead and show you how the hitch is installed.First off, well show you where the hitch attaches to the vehicle. There are two weld nuts that are located at the bottom of the frame close to the bumper.



Trailer Hitch Installation - 2010 Hyundai Santa Fe - Draw-Tite

Today on this 2010 Hyundai Santa Fe, were going to install part number 75684 from Draw-Tite. This is what the hitch looks like once installed on the vehicle. Next well go ahead and give you some measurements thatll help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pinhole to outside edge of the bumper is going to be 3 inches and from the top of the receiver opening down to the ground is going to be 13 inches. Now well go ahead and show you how the hitch is installed.First off, well show you where the hitch attaches to the vehicle. There are two weld nuts that are located at the bottom of the frame close to the bumper.



Trailer Hitch Installation - 2011 Hyundai Santa Fe - Curt

All right today on this 2011 Hyundai Santa Fe, we're going to install part number C13073 from Curt. This is what the hitch looks like when it's installed on the vehicle. Next, we'll give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the center of the hitch pin opening to the edge of the bumper is going to be 4-1/2 inches. From the top of the receiver opening down to the ground is going to be 15 inches. Now, we'll go ahead and show you how the hitch is installed.



WeatherTech Front Floor Liners Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa-Fe we are going to do a test fit of Part Number wt462981 from WeatherTech. This is our Front Floor Liners in the gray color. This is also available in black as Part Number wt442981 and tan as Part Number wt452981. We will go ahead and remove the old floor mats and then install the liners. A couple of notes about these floor liners is that they are designed to fit the vehicle. The shape, the channels and the molding all help keep dirt and debris contained on the liner and not in the carpet.



WeatherTech Rear Floor Liner Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa-Fe we are going to do a test fit of our WeatherTech Floor Liners in the 2nd row. We are working with Part Number wt440962 in the black color. This is also available in grey as Part Number wt460962 and tan as Part Number wt450962. We will go ahead and take a look and see how the liner fits in the vehicle. A couple of notes about the floor liners is they are custom molded for the vehicle, the shape to channel to the molding all help to keep dirt and debris in the liner and not in your carpet. These liners can easily be removed and cleaned with just soap and water.



WeatherTech Cargo Floor Liner Review - 2010 Hyundai Santa Fe

Today on this 2010 Hyundai Santa Fe, were going to do a test fit of part number WT42317. This is WeatherTechs cargo liner in the gray color. This is also available as black as part number WT40317 and tan as part number WT41317. Now well go ahead and remove the old floor mat and install the new floor liner. Well go ahead and check out how it fits inside. You can see how theres an edge that goes all the way around the liner which is about at the most about 1 -inch and does feather back a little bit or slant towards the tailgate area.



Husky Front and Rear Floor Liners Review - 2010 Hyundai Santa Fe

Today on this 2010 Hyundai Santa Fe, were going to do a test fit of part number HL98801 from Husky Liners. Now were working with the black color here and this is also available as gray as part number HL98802 and tan as part number HL98803. This covers the front and back. A couple notes about these floor liners is that they are custom fit to the vehicle. The shape, the channel and moldings all help to keep dirt and debris contained in the liner and not in your carpet. Underneath the liner, they have the little nibs to help keep it in place so it will not slide around as well.



Thule Flat Top Ski and Snowboard Carrier Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundia Santa-Fe we will be test fitting the Thule Flat Top Ski and Snowboard Carrier, Part Number th92725. To begin our test fit, we will simply place the front carrier over the front cross bar and bring the rubber coated steel straps around underneath the cross bar and secure it back to the foot of the carrier. We can then tighten down the grey knob which will bring the back clamp around and secure it to the vehicle. We will do this on both sides of the carrier. With the front carrier installed, we can move to the rear carrier where again, we will repeat the same procedure. Only this time, we are going to want to line it up with the front carrier to make it easier to load our skis and snowboard.



Rola Roof Cargo Basket Installation - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe well be test fitting the Rola Roof-Mounted Cargo Basket part number 59504. To begin our test fit, well simply place the roof basket on top of our factory crossbars and center the basket with the vehicle. With that done, well use the included hardware to wrap around the crossbar and secure back to the basket. And with that, our baskets secured to the vehicle and were ready to load it up. The cargo carrier will add approximately 8 inches to the overall height of the vehicle. And that completes our test fit of the Rola Roof-Mounted Cargo Basket part number 59504 on our 2010 Hyundai Santa Fe..



RockyMounts TieRod Roof Bike Rack Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe, well be test fitting the RockyMounts Tie Rod roof-mounted bike carrier part number RKY1014. To begin our test fit, well place the bike rack on top of our factor cross bar, well move to the rear mounting point where well undo the wing nut and bring the clamp underneath the crossbar where well use the wing nut to secure the rear clamp. Well move up to the front crossbar where well use the rubber-coated steel straps to go underneath the crossbar and hook back to the head of the bike rack. We can then use the Allen wrench included with the bike rack to tighten down the Allen bolt securing our rubber-coated steel straps to the front crossbar. With that done, we can reinstall the head cover on our bike rack and now were ready to load up our bike. Well take the front wheel off of our bike and place the bike on top of the bike rack.



WeatherTech Front Floor Liners Review - 2011 Hyundai Santa Fe

Today on this 2011 Hyundai Santa Fe, we are going to do a test for the part number WT462981 from WeatherTech. This is the front floor liners in the gray color. This is also available as black as part number WT442981, and tan as part number WT452981. We'll go ahead and remove the old floor mats then install the liners. inaudible liners, that they are designed to fit to vehicle, the shape, the channels, the molding, all help keep dirt and debris contained on the liner and not in you carpet. These liners can be easily removed and cleaned with just soap and water.



WeatherTech Rear Floor Liner Review - 2011 Hyundai Santa Fe

Alright today on this 2011 Hyundai Santa Fe, we will be doing a test fit of the wWeather tTech floor liners in the second row;. wWe're working with part number WT440962 in the Bblack color. This is also available as Gary Gray with part number WT460962 and Ttan as part number WT450962. Then we will go and take a look and see how the liner fits in the vehicle. A couple of notes about these floor liners, ; they were custom molded for the vehicle, the shape, the channels, the molding, all help keep dirt and debris contained on the liner and not in you carpet. These liners can be easily removed and cleaned with just soap and water.



WeatherTech Cargo Floor Liner Review - 2011 Hyundai Santa Fe

Alright today with this 2011 Hyundai Santa Fe, we're going to do a test fit for the part number WT42317 from WeatherTech. This is the floor liner for the cargo area. We'll be working with the gray color. It's also available as black with part number WT40317 and in tan as part number WT41317. Now go ahead and remove your floor mat and install the new floor liner. Check out and see how it fits inside.



Husky Front and Rear Floor Liners Review - 2011 Hyundai Santa Fe

Alright today, on this 2011 Hyundai Santa Fe, were going to do a test fit of part number hl98801 from Husky Liners. Now, Im working the black color here and this is also available in gray as part number hl98802 and tan as part number hl98803. This colors in front and back. A couple of things about these floor liners is that theyre custom-fit to the vehicle. The shape, the channels and the moldings all help to keep the dirt and debris contained in the liner and not in your carpet. Underneath the liner we have little nitch that help keep it in place so it will not slide around as well and these floor liners are easily removed and cleaned with soap and water.





Trailer Wiring Harness Installation - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe we'll be installing the Tow Ready T1 Connector, part number 118415. To begin our install we'll need to remove the rear threshold from the vehicle here at the trunk. We'll pull the handle here opening the door. To remove the threshold we'll peel the rubber molding away which will allow us to bet underneath the threshold. With our rear threshold loose we already moved the jack tools. We'll undo the three bolts that hold the tray in place.



Trailer Wiring Harness Installation - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe we're going to install the Tow Ready T1 Connector, part number 118451. First, we'll open up the rear cargo door. Then we're going to remove the storage compartment door behind both tail lights. Then were going to remove the storage compartment. To take out the rear storage compartment there are three fasteners that will need to be removed. Now we've got the storage compartment loose, we're going to go ahead and remove the rear threshold.



Trailer Hitch Installation - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe we're going to install the Curt Hitch, part number C13073. Here are a couple of measurements that will assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/2 inches. From the top of the receiver tube to the ground is 14-1/2 inches. This will assist you with selecting accessories such as a draw bar, a bike rack, or a cargo carrier. Now, lets go ahead with the installation.



Swagman Titan Hitch Bike Rack Review - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe, well be test fitting the Swagman Titan 4-Bike Carrier part S63410. Now to begin our test fit, well simply install the bike rack shank into the hitch, line up the hitch pinhole and install the anti-rattle bolt. With our bolt tight, this is what the bike rack will look like secured to the vehicle. Now well go ahead and give you a few measurements. Our ground clearance at the bike rack is 13 inches and from the closest point of the bike rack mast to the back of the vehicle is 9 inches. Now well go ahead and pull the hitch switch at the bottom of the bike to tilt our mast down.



Thule T2 Platform Style Hitch Bike Rack Review - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe we'll be test fitting the Thule T2 Platform Style Bike Carrier, part number TH917XTR. Now we've already gone ahead and slid our bike rack shank into the hitch, lined up our hitch pin hole and tightened down our anti rattle bolt. So this is what your bike rack would look like on the vehicle. Now we'll give you a few measurements. Our ground clearance at the bike rack is 10-1/2 inches, and from the closest point of the bike rack to the back of the vehicle is 2-1/2 inches. We'll now go ahead and fold the platform down and open our cargo door.



Thule Vertex 4 Hitch Bike Rack Review - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe we'll be test fitting part number TH9029, the Thule Vertex 4 Bike Carrier. To begin our test fit we'll simply slide the bike rack shank into the hitch, line up the hitch pin hole and install our anti-rattle bolt. With our anti-bolt tight, our bike rack is secured to the vehicle. Now we'll give you a few measurements. Our ground clearance at the bike rack is 10-1/2 inches, and from the closest point of the bike rack to the back of the vehicle is 9-1/2 inches. Now we'll go ahead and pull the hitch switch at the bottom of the mast to tilt our mast down.



Thule Parkway 2 Hitch Bike Rack Review - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe we'll be test fitting the Thule Parkway 2 Bike Carrier, part number TH958. To begin our test fit we'll simply slide the bike rack shank into the hitch, line up the hitch pin hole and install our anti-rattle bolt. With our bolt tight, our bike rack is secured to the vehicle and we're ready to load it up. We'll give you a few measurements. Our ground clearance at the bike rack is 11 inches, and from the closest point of the bike rack mast to the back of the vehicle is 6-1/2 inches. Now we'll go ahead and pull the pin at the bottom of the bike rack to tilt the mast down.



Thule Apex 4 Hitch Bike Rack Review - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe we'll be test fitting part number TH9025, the Thule Apex 4 Bike Carrier. To begin our test fit we'll simply slide the bike rack shank into the hitch making sure that the integrated locking hitch pin is out of the way. When we slid over the collar of the hitch we can then let go of the integrated locking hitch pin and allow it to slide into the hitch pin hole. After it's slid into the hitch pin hole we'll simply give it a slight tug and tighten down the anti-rattle knob here at the bottom of the bike rack. And with the knob tight, our bike rack is secured to the vehicle and we can load it up. And our ground clearance at the bike rack is 12 inches, and from the closest point of the bike rack mast to the back of the vehicle is 10 inches.



Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe we'll be test fitting part number S64670, the Swagman XTC2. To begin our test fit we'll simply slide the bike rack shank into the hitch, line up the hitch pin hole and install our anti-rattle bolt. And with the bolt tight, that will secure our bike rack to the vehicle. Now we'll go ahead and fold the platform down and open the trunk. And as you can see we can gain full access to the cargo area. Now we're almost ready to load our bike.



SportRack EZ Hitch Bike Rack Review - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe we'll be test fitting part number A30901, the SportRack 2 Bike Hitch Mounted Bike Rack. To begin our test fit we'll simply slide the bike rack shank into the hitch, line up the hitch pin hole and install our anti-rattle bolt. With our bolt tight, our bike rack is secured to the vehicle. Now we'll go ahead and give you a few measurements. The ground clearance at the bike rack is 15-1/2 inches, and from the closest point of the bike rack to the back of the vehicle is 8-1/2 inches. Now we'll go ahead and fold the platform down to gain access to the cargo area.



SportRack Escape 3 Hitch Bike Rack Review - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe we'll be test fitting part number A30403, the SportRack Escape 3 Bike Rack. To begin our test fit we'll simply slide the bike rack shank into the hitch, line up the hitch pin hole and install our anti-rattle bolt. With our bolt tight, our bike rack is secured to the vehicle. Now we'll go ahead and give you a few measurements. Our ground clearance at the bike rack is 10-3/4 inches, and from the closest point of the bike rack mast to the back of the vehicle is 10 inches. Now we'll go ahead and pull the pin at the bottom of the mast to tilt the bike rack mast down.



Rhode Gear Highway Hitch Bike Rack Review - 2011 Hyundai Santa Fe

Today on our 2011 Hyundai Santa Fe we'll be test fitting the Rhode Gear Highway 2 Bike Carrier, part number RG8015220. To begin our test fit we'll simply slide the bike rack shank into the hitch using the included adaptor, we'll line up the hitch pin hole and install our anti-rattle bolt. With the bolt tight this will secure our bike rack to the vehicle. Now we'll go ahead and give you a few measurements. Our ground clearance at the rack is 10 inches, and from the closest point of the bike rack mast to the back of the vehicle is 7 inches. Now we'll go ahead and pull the pin at the bottom of the mast to tilt the bike rack down and open our cargo door.



Thule Parkway 2 Hitch Bike Rack Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe we're going to do a test fit of the Thule Parkway 2 Bike Carrier, part number TH9587. With our vehicle already equipped with the 2-inch hitch and our bike rack already preassembled we'll go ahead and slide the bike rack shank directly into the receiver tube of the hitch lining up the hitch pin holes. Then we'll install and tighten down our anti-rattle bolt. This is what our bike rack will look like once it's installed on the vehicle. Next, we'll go ahead and take a few measurements. From the nearest point of the vehicle to the nearest point of the upright of the bike rack, we have 6-1/4 inches.



Thule Hitching Post Pro Hitch Bike Rack Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe we're going to be test fitting the Thule Hitching Post Pro Folding and Tilting 4 Bike Carrier, part number TH934XTR. With our vehicle equipped with the 2-inch hitch and our bike rack already preassembled we'll go ahead and slide the bike rack shank directly into the receiver tube of the hitch lining up the hitch pin holes. Then we'll install and tighten down my anti-rattle bolt. This is what our bike rack will look like in its stored position. Next, we'll go ahead and give you a few measurements. From the nearest point of our bike rack upright to the nearest point of the bumper is 6 inches.



Thule Apex 4 Hitch Bike Rack Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe we're going to be doing a test fit of the Thule Apex 4 Bike Carrier, part number TH9025. With our vehicle equipped with the 2-inch hitch and our bike rack already preassembled we can go ahead and slide the bike rack shank directly into the receiver tube of the hitch and line up the integrated hitch pin lock. Then we'll use the hand knob to secure the bike rack to the vehicle. As you can see, with the hand knob tightened down, it really takes out any sway or rattle between the bike rack and the vehicle. This is what our bike rack will look like in its stored position. Next we'll go ahead and take a couple of measurements.



Pro Series Q-Slot Hitch Bike Rack Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe, well be test fitting the Pro Series Q Slot Platform Style 2 Bike Carrier, part number PS63134. With our vehicle equipped with a 2-inch hitch and our bike rack already preassembled, we can go ahead and slide the bike rack shank directly into the receiver tube of the hitch, lining up the hitch pinholes. Then well install our 5/8 pin and take the clip. Alright, with our bike rack installed, this will look like in its stored position. Next, well go ahead and take a few measurements. From the nearest point of the vehicle to the nearest point of the platform of the bike rack is 7-1/2 inches.



Thule Vertex 4 Hitch Bike Rack Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe we're going to do a test fit of the Thule Vertex 4 Bike Carrier, part number TH9029. With our vehicle equipped with a 2-inch hitch and our bike rack already preassembled, we can go ahead and slide the bike rack shank directly into the receiver tube of the hitch lining up the hitch pin holes. Then we'll install and tighten down the anti-rattle bolt. As you can see, with the anti-rattle bolt tightened down, it really takes out any movement between the bike rack and the hitch. This is what our bike rack will look like in the stored position. Next, we'll go ahead and take a few measurements.



Thule Doubletrack Hitch Bike Rack Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe we're going to be test fitting the Thule Doubletrack Platform-Style 2 Bike Carrier, part number TH990XT. With our vehicle equipped with the 2-inch hitch and our bike rack already preassembled we'll go ahead and slide the bike rack shank directly into the receiver tube of the hitch lining up the hitch pin hole. Then we can install and tighten down the anti-rattle bolt and lock. As you can see, with the anti-rattle bolt tightened down, it really takes out any sway or movement between the bike rack and the vehicle. This is what our bike rack will look like in its stored position. Now we'll go ahead and give you a few measurements.



Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe, were going to be test fitting the Swagman XTC 2 Bike Carrier, part number S64670. With our vehicle equipped with a 2-inch hitch and our bike rack already preassembled, we can go ahead and slide the bike rack shank directly into the receiver tube, install and tighten down the anti-rattle bolt and safety clip. As you can see with the anti-rattle bolt tightened down, it really takes out any movement between the bike rack and the hitch. This is what our bike rack will look like in its stored position. Next, well go ahead and take a few measurements. From the nearest point of the vehicle to the nearest point of the bike rack, we have 5 inches of clearance.



SportRack EZ Hitch Bike Rack Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe, were going to do a test fit of the SportRack 2 Bike Hitch Mounted Bike Rack, part number A30901. Our vehicle is equipped with a 2-inch hitch and our bike is already preassembled. Well go ahead and slide the bike rack shank directly into the receiver tube of the hitch, lining up the hitch pinhole. Then we can install and tighten down the anti-rattle bolt and safety clip. As you can see with the anti-rattle bolt tightened down, it really takes out any movement between the bike rack and the vehicle. This is what our bike rack will look like in a stored position.



SportRack Escape 3 Hitch Bike Rack Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe, were going to be test fitting the SportRack Escape 3 Bike Hitch Mounted Bike Rack, part number A30403. Our vehicle is already equipped with a 2-inch hitch and our bike rack is already preassembled. So we can slide the bike rack shank directly into the receiver tube of the hitch, lining up the hitch pinhole. Then well install and tighten down our anti-rattle bolt and safety clip. As you can see with the anti-rattle bolt installed and tightened down, it really takes out any movement between the bike rack and the vehicle. This is what our bike rack will look like in its stored position.



Trailer Hitch Installation - 2008 Hyundai Santa Fe

Today on this 2008 Hyundai Santa Fe, we're going to install part number 87414 from Hidden Hitch. This is what the hitch looks like when it is installed on the vehicle. Next, we'll give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground is going to be 13 inches and from the center of the hitch pinhole to the outside edge of the bumper will be 5-3/4 inches. First thing we'll do is we'll show you where the hitch mounts up to the frame as these two existing threaded holes here. Next step is to go ahead and clean up the threaded holes.



Trailer Hitch Installation - 2008 Hyundai Santa Fe

Today on this 2008 Hyundai Santa Fe, we're going to install part number 75471 from Draw-Tite. This is what the hitch looks like when it's installed on the vehicle. Next, we'll give you some measurements that will help you out in selecting some accessories such as a ball mount, a bicycle rack, or a cargo carrier. From the top of the receiver opening down to the ground is going to be 13 inches and from the center of the hitch pinhole to the outside edge of the bumper will be 5-3/4 inches. First thing we'll do is we'll show you where the hitch mounts up to the frame as these two existing threaded holes here. Next step is to go ahead and clean up the threaded holes.



Trailer Wiring Harness Installation - 2008 Hyundai Santa Fe

Today on this 2008 Hyundai Santa Fe, we're going to install part number 118415 from Tow Ready. Now, to get access to the wiring connectors, we have to remove some flooring panels and loosen the side panels so we can get access to the wiring behind the tail light. This lid and the tray below it get removed first, the two fasteners here, here, and one on the jack. Pop, this catches loose. Alright, next, we'll go ahead and remove the threshold. Alright, we'll unscrew this fastener here and there's one up here, will do too.



WeatherTech Rear Floor Liner Review - 2008 Hyundai Santa Fe

Today on this 2008 Hyundai Santa Fe we'll be test fitting the WeatherTech Floor Liners in the second row. We'll be using part number WT440962 in the black color. This is also available in gray as part number WT460962 and in tan color part number WT450962. The WeatherTech liners are custom molded to precisely fit the vehicle and stay in place. You can see how the floor liners fit around the edge of the backseat as well as the rails on the front seat. This also has a raised portion or a pocket to accommodate the factory hooks.



WeatherTech Front Floor Liners Review - 2008 Hyundai Santa Fe

Today on this 2008 Hyundai Santa Fe, were going to be test fitting WeatherTech Floor Liners in the front row. This will be part number WT440961. This is the black color. This is also available in gray as part number WT460961 and in tan color WT450961. First, well go ahead and remove the original floor mats and then we install the new WeatherTech mats. They are custom molded to the vehicle to ensure the exact fit.



Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2008 Hyundai Santa Fe

All right today on this 2008 Hyundai Santa Fe, were going to do a test fit for the part number S64670 from Swagman, the XTC-2 Bike Carrier. One quick note about this bike rack that it will work with 1 inch receiver hitches both class 1 and class 2, and will also work with a class 3 receiver or a 2-inch by 2-inch receiver with the included spacer. Well start off our test fit by installing the anti-rattle bolt and put the safety pin on the other side. Now well give some clearance measurements. From the back hatch to the bike rack, were looking at 7 inches. Ground clearance by the hitch will be 11 inches and ground clearance from the very back of the bike rack will be 14 inches.



Thule Vertex 4 Hitch Bike Rack Review - 2008 Hyundai Santa Fe

Today on this 2008 Hyundai Santa Fe, were going to do a test fit on part number TH9029 from Thule, the Vertex 4 Bike Carrier. One note about this bicycle rack is that it will work for an inch and a quarter receiver hitches, both class one and class two, however the class one receiver hitch youre only limited to two bikes, and well work with a class two receiver hitch with the included spacer, okay. Were going to start off with test fit by installing the bike rack into the hitch, and we will install the anti-rattle bolt. Put the bike rack in its storage position, well go ahead and get some measurements. As closest point of contact to the bumper, were looking at two to quarter inches. Ground clearance will be ten and inches.



Thule Doubletrack Hitch Bike Rack Review - 2008 Hyundai Santa Fe

Right today its 2008 Hyundai Santa Fe, were going to do a test fit for the part number TH990XT from Thule, Doubletrack Platform Bicycle Rack. This is bicycle rack will work with class one and class two receiver hitches and will also work with two inches receiver hitches with the provided spacer. We start off for tested by installing the bike rack into the hitch. They will install an anti-rattle bolt and put the lock on the other side. All right were going and fold the bike rack and gives some measurements on clearance. All right, as closest point on contact between the hitch switch and the bumper, were looking at two and a half inches.



Thule Apex 4 Hitch Bike Rack Review - 2008 Hyundai Santa Fe

All right today its 2008 Honda Santa Fe. Were going to do a test to the part number TH9025 from Thule. This is the Apex 4 Bicycle Rack. One quick note about this bicycle rack, they will work with a inch and quarter receiver hitches, both class one and class two. However, when you use it on a class one hitch, youre only limited to two bicycles. This will also work with two-inch receive hitch with the provided spacer.



Westin Tube Step Installation - 2011 Hyundai Santa Fe

Today on this 2011 Hyundai Santa Fe, were using tube steps part number 22-5050 and Installation Kit 22-1815.Were gonna start by laying all the parts because the brackets have a front and rear to them. So, front bracket, a tube step and our rear bracket. Next we need to do in the vehicle. Right next to the rear wheel, theres a rubber plug, well just pop it out of the way. Were working on the passenger side of the vehicle. Now, on the frame rail theres an oval plug that we have to remove as well.



Yakima LoadWarrior Roof Cargo Basket Review - 2011 Hyundai Santa Fe

Today on this 2011 Hyundai Santa Fe, we will go ahead and do test fit, on part number y07070 from Yakima; this is a load warrior roof rack basket. The Hyundai of the factory roof rack system already installed, we can go ahead and mount up to that. One feature about this basket, it does come with custom glaring help reduced windows. Now well go ahead and try it on the vehicle and see how it fits. You definitely want to have an extra set of hands to install this. Once you have the cargo basket in its initial place well go ahead loosen and install the hardware.



Thule MOAB Roof Top Cargo Basket Review - 2011 Hyundai Santa Fe

Today on this 2011 Hyundai Santa Fe, we're going to test the part number TH690 from Thule, the M.O.A.B. Roof Top Cargo Basket. A few things about this Cargo Carrier, it comes with custom fairing that reduces wind resistance for a quiet ride. The mounting hardware allows easy installation and removal. Speaking of mounting, however, the crossbars spread should be 16" up to 28". All right.



Trailer Hitch Installation - 2011 Hyundai Santa Fe

Today on this 2011 Hyundai Santa Fe, were gonna install a Hidden Hitch part 87574.Here are a couple of measurements that will assist you in selecting accessories for your new hitch. Well start from the hitch pinhole to the outermost part of the bumper is 3 inches. From the top of the receiver tube to the ground is 14 inches. This will assist you in selecting accessories. Now lets go ahead with the installation.Before I attempt to install my hitch, I wanna clean out my fastening points, the two weld nuts on the frame. We have two on each side.



Trailer Hitch Installation - 2011 Hyundai Santa Fe

Today on this 2011 Hyundai Santa Fe, we are going to install Draw-tite part number 75684. Here are a couple of measurements that will assist you with selecting accessories for new hitch. From the center of the hitch-pinhole to the outermost point of the bumper is 3 and a quarter inches. From the top of the receiver-tube to the ground is 14 inches. This will assist you with selecting accessories. Now lets go ahead with the installation.



Trailer Wiring Harness Installation - 2003 Hyunai Santa Fe

Today we're working on a 2003 Hyundai Santa Fe. We're going to install Tow Ready T1 Connector, product number 118473. First, we're going to access the rear cargo area of the vehicle. I'm going to go ahead and push the rear seats forward and then we're going to remove the cargo cover and then we're going to remove the rear cargo trays on both sides and the center. Next, we'll go ahead and remove the cargo hooks from the rear frame. There's the cargo hook on the passenger's side, I'll go ahead and repeat the same process on the driver's side.



Trailer Hitch Installation - 2003 Hyundai Santa Fe

Today we are working on a 2003 Hyundai Santa Fe. Were going to install hidden hitch part number 87419. This will also be comparable to the Draw Tite part number 41543. Here are a couple of measurements that will assist you with selecting accessories for your new hitch such as a bike rack, cargo carrier, or draw bar. From the center of the pin hitch hole to the outer most point of the bumper is 2-1/2, from the top of the receiver tube to the ground is 14-1/2. Now lets go ahead with the installation.



Trailer Hitch Installation - 2008 Hyundai Santa Fe

Today we will be working on a 2008 Hyundai Santa Fe. We will be installing Curt hitch part number 13538. Here are a couple of measurements that will assist you when ing accessories for your new hitch. From the center of the hitch pin hole to the outermost point of the bumper is 5-1/2 inches. And from the top of the receiver tube to the ground is 13-3/4 inches. This will assist you with ing accessories such as a draw bar, a bike rack or a cargo carrier. Now let us go ahead with the installation. 0:32



Trailer Hitch Installation - 2009 Hyundai Santa Fe

Today on this 2009 Hyundai Santa Fe we will be installing Curt part number 13538. A couple of measurements to be aware of when ing accessories, such as a drawbar, bike carrier or cargo carrier, would be from the center of the hitch pin hole to the outer most point of the bumper is 5-1/2 inches. And from the top of the receiver tube to the ground is 15 inches. I would first like to point out where our mounting holes are going to be on the rear sub frame of the vehicle. It is almost identical on each side. These are factory mounted holes and being factory threaded holes what we are going to want to do is make sure those threads are free and clear of any dirt and debris. So I am going to take part number 814092, a nylon tube brush, and some lubricant and flush those holes out now. And again we are just cleaning those threads out to make it easy for our new bolts to go in when we go to install our hitch. 1:04



Trailer Wiring Harness Installation- 2002 Hyundai Santa Fe

Today on this 2002 Hyundai Santa Fe we are going to be installing wiring harness part number 118473 from Tow Ready. The first thing we are going to do is clean out our trunk and remove the threshold cover and cargo trays. To remove the threshold here we are going to have to remove these screws t hat are holding it in position along with the 10 millimeter bolt in the center. Then we will pop the rivets off. :30



Trailer Hitch Installation - 2002 Hyundai Santa Fe

Today on this 2002 Hyundai Santa Fe we are going to be installing part number 87419 from Hidden Hitch. As you can see we already removed our spare tire. Then we are going to lower the exhaust. First thing we are going to do is remove our exhaust hangers after we lower our spare tire. We are just going to lubricate up the hangers. There is going to be two on both sides of the muffler at the rear most of the vehicle. We are just going to lube them up with WD-40 and then we are going to slide them off. 00:29



Trailer Hitch Installation - 2004 Hyundai Santa Fe

Today, on this 2004 Hyundai Santa Fe, we will be installing Hidden Hitch part number 87419. This installation will also apply to the Draw-Tite part number 41543. Okay, a couple things we want to do in preparation to installing our trailer hitch, we want to first go ahead and lower down our space tire and get it out of the way. We are also going to need to go ahead and lower the exhaust. We just need to remove that off of the two rear most hangers and then the one at the forward side of the exhaust. To remove the hangers, we want to go ahead and spray down the studs with a spray lubricant, like a WD-40. And we will just take a pair of pliers and pry it right off there. We want to repeat that for all three of the hangers. We also want to make sure that we support the exhaust tube here before we remove the third hanger. Once we do, the exhaust could fall and possibly damage it. 0:52



Trailer Hitch Installation - 2009 Hyundai Santa Fe

On this 2009 Hyundai Santa Fe we are going to install part number 87414 from Hidden Hitch. This will also apply to part number 75471 from Draw-Tite. Looking at the passenger side of the vehicle we will show you where the hitch mounts up on the frame. It mounts on the two existing threaded holes on the bottom of the frame, here and here, so it is pretty easy to install. What you want to do is take some time out and run the bolts in first by themselves and make sure you clear out any debris or anything like that to keep it from running the bolts in. :28



Trailer Wiring Harness Installation - 2009 Hyundai Santa Fe

Today on this 2009 Hyundai Santa Fe, we are going to install part number 118415 from Tow Ready. This T1 connector will actually install behind the tail lights, so everything will be stored inside when we are done. So that means we have to get inside the vehicle and take apart some panels, so we can install the wiring. Let us open our lid here, that can stay and this tray has to come off also. We are going to take off the threshold by the latch. And we also have to loosen both panels on the side of the vehicle behind the tail lights. :49



Trailer Wiring Harness Installation - 2005 Hyundai Santa Fe

Today we are going to be installing wiring harness part number 118473 on a 2005 Hyundai Santa Fe. Taking a look at the wiring harness, you can see we have got two main ports coming off of the Modulite box. We have got one with the yellow and brown wires. That one is going to connect behind the drivers side tail light assembly. The other connector, with the green and red wires, is going to be connected behind the passengers side tail light assembly. We have also got a white terminal here on the drivers side connector. That is for the ground, securing that to a metal surface. The black box in the middle is our converter box. And then, coming off the other end, we have got our 4-pole connector. And that will be staying inside the vehicle in this application.



Trailer Hitch Installation - 2005 Hyundai Santa Fe

Today we are going to be installing Hidden Hitch part number 87419 on a 2005 Hyundai Santa Fe. This hitch application will also apply for Draw-Tite part number 41543. Looking underneath the vehicle, we have gone ahead and removed the spare tire to get it out of the way. Looking at the drivers side frame rail, you can see we have got a bolt here at the end of the frame and three bolts that are attaching the tow hook to the frame, and then an extra weld nut here. Those are going to provide all of our attaching points here on the drivers side.



Trailer Hitch Installation - 2007 Hyundai Santa Fe

Alright, today we are going to install part number 75471 from Draw-Tite and we will be installing this on a 2007 Hyundai Santa Fe. This also applies to hidden hitch number 87414. It is a relatively easy hitch to install. It attaches at 2 points right here, at these 2 threaded holes inside the frame. They are going to be identical on both sides of the vehicle. So first thing we will want to do, even though this is a new vehicle, is take some time out to run the bolts in and out just to make sure that you do not have any dust or road grime in there.





Hyundai Santa Fe Questions and Answers


all Hyundai Santa Fe questions      



Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email



Only 18 Hours 55 Minutes Remaining

etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com