Select Your Vehicle
view cartView Cart
Only 3 Hours 59 Minutes Remaining

Honda Ridgeline owners are most interested in these products

change vehicle



Honda Ridgeline Videos

Rain-X Latitude Wiper Blades Installation - 2007 Honda Ridgeline

All right. Today on this 2007 Honda Ridgeline, we're going to do a test fit on the Rain-X Latitude Windshield Wipers Part Number RX5079280. Couple things to know about this wiper blade that it is designed to meet or exceed OEM's standards. This wiper blade is constructed from a rust-resistant galvanized steel frame and the blade is constructed from all natural rubber with integrated UV inhibitors to protect it from the sunlight. All right. We'll start off our test fit by removing the original wind shield wiper blades, there's a little tab located right here that we push up that will release the blade from the arm.



Rain-X Weatherbeater Wiper Blades Installation - 2007 Honda Ridgeline

Today, on a 2007 Honda Ridgeline, were going to do a test fit on part number RX30224 from Rain-X. This is our Weatherbeater Wiper Blade. A couple of things to know about this wiper blade is that it is designed to meet or exceed OEM standards. This wiper blade is constructed from a rust resistant galvanized steel frame, and the blade is constructed from all natural rubber with integrated UV inhibitors to protect it from the sunlight. Well start off our test fit by removing the original wiper blades. Theres a small tab located underneath the arm, that you push up and then you go ahead and pull the blade away.



Trailer Wiring Harness Installation - 2007 Honda Ridgeline

Today on this 2007 Honda Ridgeline we're going to install part number 118400 from Curt. First step is to go ahead and lower the tailgate and remove the two screws that attach the tail lights to the vehicle on the drivers side. We'll go ahead and remove the tail lights and then disconnect the wiring harness. Now there's two little tabs. There's one tab that connects the wire harness to the body, you have to push that away to release it and one the second tab we push down and that will allow u s to pull the connector apart. We'll go ahead and repeat the same process over on the passenger side.



Trailer Hitch Installation - 2007 Honda Ridgeline - Draw-Tite

Today on this 2007 Honda Ridgeline, were going to install part number 75280 from Draw Tite. This is what the hitch looks like when its installed on the vehicle. Next well go ahead and give you some measurements to help you out in selecting some accessories, such as a ball mount, bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be 16 inches, and from the center of the hitch pin hole to the edge of the bumper will be three and a quarter inches. Now well go ahead and show you how the hitch is installed. Our first step is to go ahead and lower the exhaust and get it out of the way to give us some more working room so we can slide the hitch into place.



Trailer Hitch Installation - 2007 Honda Ridgeline - Hidden Hitch

Today on this 2007 Honda Ridgeline, were going to install part number 70754 from Hidden Hitch. This is what the hitch looks like when its installed on the vehicle. Next well go ahead and give you some measurements to help you out in selecting some accessories, such as a ball mount, bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be 16 inches, and from the center of the hitch pin hole to the edge of the bumper will be three and a quarter inches. Now well go ahead and show you how the hitch is installed. Our first step is to go ahead and lower the exhaust and get it out of the way to give us some more working room so we can slide the hitch into place.



Trailer Wiring Harness Installation - 2008 Honda Ridgeline

Today on this 2008 Honda Ridgeline, were going to install part number C55585 from Curt. The first thing we need to do is go ahead and remove the two taillights. You have to open up the tailgate, remove the two fasteners on the inside and then we can pop the taillights loose. Then we need to disconnect the wiring harness. Theres a little tab on the end that you just push away from the connector to loosen it up. Now well go ahead and start installing the wiring harness.



Trailer Wiring Harness Installation - 2008 Honda Ridgeline

Today on this 2008 Honda Ridgeline, were going to install part number 118400 from Tow Ready. The first thing we need to do is go ahead and remove the two taillights. You have to open up the tailgate, remove the two fasteners on the inside and then we can pop the taillights loose. Then we need to disconnect the wiring harness. Theres a little tab on the end that you just push away from the connector to loosen it up. Now well go ahead and start installing the wiring harness.



Trailer Hitch Installation - 2007 Honda Ridgeline - Curt

All right today is 2007 Honda Ridgeline were going to install part number 13385 from Curt. All right this is what the hitch looks like once installed on the vehicle. Next well go ahead and give you some measurements to help you out in selecting some accessories such as a ball mount, a bicycle rack or a cargo carrier. The top receiver opening down to the ground, were looking at distance of 16- inches and from the center of our hitch pin hole to the edge of the bumper were looking at distance of 4 inches. All right, now well go ahead and show you how the hitch is installed. First step is go ahead and lower exhaust and get out of the way to give us some more working room so we can slide the hitch into place.



Trailer Hitch Installation - 2008 Honda Ridgeline - Curt

Today on this 2008 Honda Ridgeline, we're going to install Part Number 13385 from Curt. All right. Now, this is what the hitch looks like once installed on the vehicle. Next, we'll go ahead and give you some measurements that will help you out in selecting some accessories such as the bicycle rack, a cargo carrier or a ball mount. From the top of receiver opening down to the ground will be 17 inches and from the center of the hitch pinhole to the edge of the bumper will be 3-3/4 inches. Now, we'll go ahead and show you how the hitch is installed.



Rain-X Latitude Wiper Blades Installation - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Rain-X latitude wiper blades, driver side part number rx5079279. To begin our test fit well first need to remove the factory or previously installed wiper blades. This vehicle features a J-hook, so we push up on the black button located at the center of the wiper blade and pull the wiper blade down; repeat this step for the opposite side. Now to install the new Rain-X latitude wiper blades, youll take the center of the wiper blade and slide it into the J-hook until you hear a click. Once you hear a click youll know this wiper blade has been successfully installed, repeat the steps for the other side. That completes the test fit for the Rain-X latitude wiper blades, driver side part number rx5079279 on our 2013 Honda Ridgeline..



Rain-X Weatherbeater Wiper Blades Installation - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Rain-X weather beater rocker blades driver side, part number rx30222. To begin our test fit well first need to remove the factory or previously installed wiper blades. This vehicle features a J-hook, youll first need to push the black button located at the center of the wiper and pull the wiper blade down. Well now install the new Rain-X weather beater rocker blades. Well slide the wiper blade into the J-hook and once you hear a click youll know the wiper blades have been correctly installed. Well repeat the same process for the opposite side and that concludes todays test fit for the Rain-X weather beater rocker blades driver side, part number rx30222 on our 2013 Honda Ridgeline.



Thule XB16 Snow Tire Chains Review - 2008 Honda Ridgeline

All right, today were going to do a test fit of part #: TH01571250 from Thule. This is the XB16 model. Now, well be working with tire size 245/65-17 and this will be on a 2008 Honda Ridgeline. Before the install you always want to double check with your owners manual to check for any limitations. In this case the manufacturer states that you should use the snow chains only on the front wheels. Now to start off the test fit well take our chain and well wrap it around the back side of the tire and well make sure that the one half of the cable with the yellow is going to the right side of the tire.



Yakima HighLite 2 Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Yakima Highlite aluminum two bike carrier, part number Y02438. To begin our test fit well slide the shank of the carrier into the opening of the hitch, align up our pin hole, slide our security pin through the pin hole and turn the black knob at the base of the carrier to engage our anti-rattle device. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about six inches. Weve added about 10 inches to the overall length of the vehicle.



Thule Vertex 4 Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Thule Vertex four bike carrier, part number TH9029. To begin our test fit well slide the shank of the carrier into the opening of the hitch, align up our threaded pin holes, thread our anti-rattle bolt through the threaded pin holes and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 16 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about four inches. Weve added about 13 inches to the overall length of the vehicle.



Yakima StickUp 2 Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on this 2012 Honda Ridgeline well be test fitting the Yakima Stickup two bike carrier, part number Y02420. To begin our test fit well slide the shank of the carrier into the opening of the hitch tube, line up our threaded pin holes. Well thread the anti-rattle bolt through the pin hole and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 5 inches.



Thule AeroBlade Traverse Roof Rack Installation - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Thule Aeroblade roof rack system, part numbers THARB60, TH480R, and THKIT1510. To begin our test fit with the roof racks already assembled well go ahead and open the front passenger and driver side door. Well sit the front crossbar onto the roof and measure from the glass to the first part of the foot. Our measurement is 10 inches. Once weve measured both the drivers and passenger side front crossbar 10 inches from the first part of the front window well go ahead and tighten down the drivers side and passenger side feet of the crossbars using the included tool. Once the front crossbar is tightened down and secured well go ahead and close the doors.



Thule T2 Platform Style Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Thule T2 platform style two bike carrier, part number TH916XTR. To begin our test fit well slide the shank of the carrier into the opening of the hitch tube, align our threaded pin holes, thread our anti-rattle bolt through the threaded pin holes and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 2 inches. Weve added about 13 inches to the overall length of the vehicle.



Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Thule Standup paddle board carrier, part number TH810. To begin our test fit sit the carrier on top of the crossbars, wrap the black straps around the crossbars and turn the gray knobs to tighten. You want to make sure that your carriers are parallel to each other and that they are position symmetrically to the crossbars so that your cargo can be secured correctly. That concludes todays test fit for the Thule Standup paddle board carrier, part number TH810, on this 2013 Honda Ridgeline.



Thule MOAB Roof Top Cargo Basket Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline well be test fitting the Thule Mother of All Baskets top cargo carrier, part number TH690. To begin our test fit well sit the carrier onto the crossbars and get it perpendicular from the crossbars. Once we have established where the basket needs to be well go ahead and swing the brackets underneath the crossbars and tighten up the brackets using the wing nut. Well tighten up the brackets on all four sides. That concludes our test fit of the Thule Mother of All Baskets top cargo carrier, part number TH690, on our 2013 Honda Ridgeline.



Thule Hitching Post Pro Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Thule Hitching Post Pro, part number TH934XTR. To begin our test fit well slide the shank of the carrier into the opening of the hitch tube, align up our threaded pin holes, thread our anti-rattle bolt through the threaded pin holes and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 16 inches of ground clearance. The closest part of the carrier to the closest part of the vehicle is about seven inches. Weve added about 17 inches of overall length to the vehicle.



Thule Flat Top Ski and Snowboard Carrier Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline well be test fitting the Thule Flattop ski and snowboard carrier, part number TH92725. To begin our test fit well sit the carrier onto the crossbars and wrap the black straps around the crossbars and turn the gray knob to tighten them down. Well again do this for the rear crossbars as well. Once the carrier on the front crossbar and the rear crossbar are tightened down were ready to load our cargo. To load the cargo push the gray button located at the ends of the carriers to open up the jaws. Well then sit our cargo inside the jaws and make sure theyre parallel.



Thule Echelon Roof Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Thule Echelon roof mounted bike carrier, part number TH518. To begin our test fit well go ahead and sit the carrier onto the crossbars, take the brackets and put them on the other side of the crossbars and tighten them down. Youll need to make sure that your carrier is exactly perpendicular to the crossbars so that your carrier can fit snug on the crossbars. Once you get the carrier tightened down youre ready to load the bike. Before we load the bike well first need to loosen up the skewer and undo the tray strap. Well sit the bike onto the skewer, tighten down the skewer, and secure it with the tray strap.



Thule Doubletrack Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Thule Doubletrack platform style two bike carrier, part number TH990XT. To begin our test fit well slide the shank of the carrier into the opening of the hitch tube, align up our threaded pin holes. Well then thread our anti-rattle bolt through the threaded pin hole and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 16 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about three inches.



Thule Domestique Roof Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Thule Domestique fork-mount bike carrier, part number TH513. To begin our test fit well loosen up the brackets of the carrier and slide them onto the cross bars. Youll want to get the carrier perpendicular to the cross bars. Once you have fitted the carrier perpendicular to the cross bars, tighten up the brackets. To load the bike insert the skewer to the front of the carrier and undo the tray strap. Set the bike onto the carrier and set the forks onto the skewer.



Thule Apex 4 Swing Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Thule Apex Swing four bike carrier, part number TH9027. To begin our test fit well slide the shank of the carrier into the opening on the hitch, line up our pin hole, insert our spring loaded security pin and turn the black knob locate at the base of the carrier to engage our anti-rattle device. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 18 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about one and a half inches. Weve added about 13 inches to the overall length of the vehicle.



Thule Apex 4 Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Hone Ridgeline well be test fitting the Thule Apex four bike carrier, part number TH9025. To begin our test fit well slide the shank of the carrier into the opening of the hitch tube, align up our pin hole, insert the spring loaded safety pin and turn the black knob located at the base of the carrier to engage our anti-rattle device. Now lets go over some clearance measurements to see how this bike carrier and the vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 1 inches. Weve added about 12 inches to the overall length of the vehicle.



Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline well be test fitting the Swagman XTC2 bike carrier, part number S64670. To begin our test fit well slide the shank of the carrier into the opening of the hitch tube, align up our threaded pin holes, thread our anti-rattle bolt through the threaded pin hole and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about six inches. Weve added about 22 inches to the overall length of the vehicle.



Swagman Titan Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline well be test fitting the Swagman Titan four bike carrier, part number S63410. To begin our test fit well slide the shank of the carrier into the opening of the hitch, align our threaded pin holes, thread our anti-rattle bolt through the threaded pin holes and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 9 inches. Weve added about 22 inches to the overall length of the vehicle.



Swagman Fork Down Roof Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Swagman fork style roof mounted bike carrier, part number S64710. To begin our test fit well go ahead and sit the carrier onto the crossbars and position the carrier perpendicular to the crossbars. Once the carriers positioned on the crossbars well go ahead and take our brackets, sit the brackets underneath the crossbars and secure them with the wing nuts. Once the carrier is tightened down and secure were ready to load our bike. To load our bike well first loosen up the skewer and undo the tray strap. Well sit the forks of the bike onto the skewer and tighten up the skewer and secure it with the tray strap.



Surco Hitch Cargo Carrier Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Surco 24 by 60 cargo carrier, part number 52018. To begin our test fit well slide the shank of the carrier into the opening of the hitch tube, align up our hitch pin hole, slide our pin through our hitch pin hole and secure it with a clip. Now lets go over some clearance measurements to see how the carrier and this vehicle fit together. Theres about 16 inches of ground clearance from the rear of the carrier. The closest part of the vehicle to the closest part of the carrier is about 3 inches. The closest part of the carrier to the closest part of the vehicles exhaust tip is about 9 inches.



SportRack Nomad Roof Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Sportrack Nomad frame bike carrier, part number ABR611. To begin our test fit well sit the carrier onto the crossbars and align up the carrier perpendicular to the crossbars. Once the carrier is exactly perpendicular to the crossbars we can take the bracket, out the brackets under the crossbars, and tighten them using the wing nut. Once the carrier is tightened down were ready to load the bike. To load the bike, sit the bike onto the tray and secure the frame hook tightly against the frame. Once the frame hook is tightly in place you can secure it with the tray straps.



RockyMounts Euro PitchFork Roof Bike Rack Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline well be test fitting the Rocky Mounts Euro Pitchfork roof mounted bike carrier, part number RKY1103. Before we begin our test fit well need to take the end caps off of the crossbars and take out the weather stripping to make room for our carrier. Now that this has been completed well take the carrier, using an Allen wrench, and loosen up the bolts and slide the carrier into the openings of the crossbars. Once you get the carrier perpendicular to the crossbars, using the Allen key again, youll tighten down the bolts and then putting the end caps back into the crossbars. To load the bike, first loosen up the skewer and then undo the tray strap. Sit the bike onto the carrier, tighten up the skewer, and secure with the tray strap.



Pro Series Q-Slot Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline well be test fitting the Pro Series Q-Slot platform style two bike carrier, part number PS63134. To begin our test fit well slide the shank of the carrier into the opening of the hitch tube, align up our pin hole, slide our pin through the pin hole and secure it with a clip. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 10 inches. Weve added about 26 inches to the overall length of the vehicle.



Kuat Sherpa Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline well be test fitting the Kuat Sherpa aluminum bike carrier, part number S102. To begin our test fit well slide the shank of the carrier into the opening of the hitch and turn the black handle located at the base of the carrier to engage our anti-rattle device. Now lets go over some clearance measurements to see how the bike carrier and the vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 1 inches. Weve added about 13 inches to the overall length of the vehicle.



Hidden Hitch Ball Mount with 6 Inch Drop Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline, well be test fitting the Hidden Hitch Ball Mount, part #80240. Before we begin our test fit, well need to get the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our measurement is 19 inches. This measurement can vary from tire size or aftermarket accessories. To begin our test fit, in the drop position, well go ahead and slide the shank of our ball mount into the opening of the hitch, line up our pinhole, slide our pin through the pinhole and secure with the clip.



Curt 20x60 Folding Aluminum Cargo Carrier Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline well be test fitting the Curt 20 by 60 folding aluminum cargo carrier, part number C18100. To begin our test fit well slide the shank of the carrier into the opening of the hitch tube, align up our hitch pin hole, slide our pin through our hitch pin hole and secure it with a clip. Now lets go over some clearance measurements to see how the cargo carrier and this vehicle fit together. With the cargo carrier folded up theres about 15 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 2 inches. With the cargo carrier folded down theres about 17 inches of ground clearance from the rear of the carrier.



Curt Hitch Cargo Carrier Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline, well be test fitting the Curt 20x48 Cargo Carrier, part #C18145. To begin our test, fit well slide the shank of the carrier into the opening of the hitch, line up our threaded pinholes, thread our anti-rattle bolt through the threaded pinhole and tighten it with a wrench. Now, lets go over some clearance measurements to see how the cargo carrier and this vehicle fit together. Theres about 16 inches of ground clearance from the rear of the carrier. The closest part of the vehicle to the closest part of the carrier is about 3 inches. The closest part of the carrier to the closest part of the vehicles exhaust tip is about 9 inches.



SportRack EZ Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline, well be test fitting the SportRack 2-Bike Carrier, part #A30901. To begin our test fit, well slide the shank of the carrier into the opening of the hitch, align our threaded pinholes, thread our anti-rattle bolt, through the threaded pinholes and tighten it with the wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 9 inches. Weve added about 26 inches to the overall length of the vehicle.



SportRack Escape 3 Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline, well be test fitting the SportRack Escape 3-Bike Carrier, part #A30403. To begin the test fit, well slide the shank of the carrier into the opening of the hitch, line up our threaded pinholes, thread our anti-rattle bolt through the threaded pinholes and tighten it with the wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 4 inches. Weve added about 13 inches to the overall length of the vehicle.



Softride Dura Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline, well be test fitting the Softride Dura Parallelogram Tilting 4-Bike Carrier, part #SR26247. To begin our test fit, well slide the shank of the carrier into the opening of the hitch tube, line up our threaded pinholes, thread our anti-rattle bolt through the threaded pinholes and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 16-1/2 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 7 inches. Weve added about 36 inches to the overall length of the vehicle.



Rola Hitch Cargo Carrier Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline, well be test fitting the Rola 23x56 Railed Cargo Carrier, part #59502. To begin our test fit, well slide the shank of the carrier into the opening of the hitch tube, line up our pinhole, slide our pin through our pinhole and secure it with a clip. Now well go over some clearance measurements to see how the carrier and this vehicle fit together. Theres about 19 inches of ground clearance from the rear of the carrier. The closest part of the vehicle to the closest part of the carrier is about 9 inches. The closest part of the carrier to the closest part of the vehicles exhaust tip is about 18 inches.



RockyMounts TieRod Roof Bike Rack Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline, well be test fitting the RockyMounts TieRod Roof-Mounted Bike Carrier, part #RKY1014. To begin our test fit, well undo the bracket at the rear of the carrier and set the carrier onto the crossbars. Take off the top plastic cover and secure the rubber grips around the front crossbar then replace the cover. Well move on to the rear of the carrier. Well swing the bracket around the underneath side of the rear crossbar and use the Allen key to tighten up the bracket. To load the bike, first, well loosen up the skewer and undo the tray strap, set the bike onto the carrier, tighten up the skewer and secure it with the tray strap.



Pro Series Eclipse 4 Hitch Bike Rack Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline, well be test fitting the Pro Series Eclipse 4 Bike Carrier, part #63124. To begin our test fit, well slide the shank of the carrier into the opening of the hitch tube, line up our threaded pinholes, thread our anti-rattle bolt to the threaded pinholes and tighten with a wrench. Now, lets go over some clearance measurement to see how the bike carrier and this vehicle fit together. Theres about 16-1/2 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 5-1/2 inches. We added about 32 inches to the overall length of the vehicle.



Pro Series Hitch Cargo Carrier Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline, well be test fitting the Pro Series 24x60 Railed Cargo Carrier, part #63153. To begin our test fit, well slide the shank of the carrier into the opening of the hitch tube, line up our pinhole, slide our pin though our pinhole and secure with a clip. Now, lets go over some clearance measurements to see how the cargo carrier and this vehicle fit together. Theres about 19-1/2 inches of ground clearance from the rear of the carrier. The closest part of the vehicle to the closest part of the carrier is about 11 inches. The closest part of the carrier to the closest part of the vehicles exhaust tip is about 18 inches.



Draw-Tite Ball Mount Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline, well be test fitting the Draw-Tite Ball Mount, part #2923. Before we begin our test fit, we need to get the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our measurement is 19 inches. Now, well begin our test fit. In the drop position, well slide the shank of the ball mount into the opening of the hitch, line up our hitch pinhole, slide our pin through our pinhole and secure with a clip.



Curt Tri-Ball Mount Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline, well be test fitting the Curt Tri-Ball Mount, part #C45001. Before we begin our test fit, well need to get the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our measurement is 19 inches. To begin our test fit, well go ahead and slide the shank of the ball mount into the opening of the hitch tube, line up our pinhole, slide our pin through our pinhole and secure with a clip. With this ball mount not having a rise or a drop, well use the measurement for our hitch height.



Curt Folding Hitch Cargo Carrier Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline, well be test fitting the Curt 24x60 Folding Cargo Carrier, part #C18132. To begin our test fit, well slide the shank of the carrier into the opening of the hitch. Well line up our hitch pinhole, slide our pin through our pinhole and secure with a clip. Now, lets go over some clearance measurements to see how the cargo carrier and this vehicle fit together. With the cargo carrier folded up, we have about 16-1/2 inches of ground clearance. The closest part of the carrier to the closest part of the vehicle is about 1/4 inch.



Convert-A-Ball 6-Way Multi-Hitch Ball Mount Review - 2013 Honda Ridgeline

Today on this 2013 Honda Ridgeline, well be test fitting the Convert-A-Ball Cushioned 6-Way Multi-Hitch Ball Mount, part #CAB-6W. Before we begin our test fit, well first get the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Ours is about 19 inches. To begin our test fit, well slide the shank of the ball mount into the opening of the receiver tube, line up our pinhole, slide our pin through our pinhole and secure with a clip. With this ball mount not having a rise or a drop, we will use the hitch height of 19 inches.



Convert-A-Ball Ball Mount with 4 Inch Drop Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline, well be test fitting the Convert-A-Ball cushioned ball mount, part #AMSC4. Before we begin our test fit, well first need to get the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our measurement is 19 inches. To begin our test fit in the drop position, well go ahead and slide the shank of the ball mount into the opening of the hitch, line up our pinholes, slide our pin through our pinhole and secure with the clip. Well then measure from the ground to the top of the ball platform and get a measurement of 14 inches.



Convert-A-Ball Ball Mount with 2 Inch Drop Review - 2013 Honda Ridgeline

Today on our 2013 Honda Ridgeline, well be test fitting the Convert-A-Ball Cushioned Ball Mount, part #AMSC2. Before we begin our test fit, well need to get a hitch height for our vehicle. This is the measurement from the ground to the inside top of the receiver tube. Our measurement is 19 inches. To begin our test fit in the drop position, well go ahead and slide the shank of the ball mount into the opening of the hitch, line up our pinhole, slide our pin through up there and secure it with a clip. Well now go ahead and measure from the ground to the top of the ball platform while in the drop position.



Trailer Hitch Installation - 2008 Honda Ridgeline

Today we are installing a hitch on a 2008 Honda Ridgeline hitch number 75280. We are going to start off showing you the holes where the hitch will mount up to. It is these three here and it is the same on the other side, plus being two more on the fascia. The first step to lowering the exhaust, sometimes it helps to spray some type of lubricant on the hanger itself so you can take off the rubber grommet easier. So after you do the first one, then you do the same to the back. In some cases, after you lower the exhaust, the heat shield that is around it may come down, as well, so you have more clearance and more access in getting to the bolts on the hitch install. In this case, the heat shield is flexible enough to just move it out of the way to get the hitch installed.





Honda Ridgeline Questions and Answers


all Honda Ridgeline questions      



Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email



Only 3 Hours 59 Minutes Remaining

etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com