Trailer Hitch Installation - 2013 Honda Accord - Hidden Hitch
Today, on our 2013 Honda Accord well be installing Hidden Hitch part number 60325. This is what our hitch will look like once its installed. Next, well go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch such as: a ball mount, a bike rack or cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is 2 inches, from the top of the receiver tube opening to the ground is 10 inches.Now, lets go ahead with installation. Before we begin our install well first need to lower the exhaust. To lower the exhaust well remove the two rubber isolators, one behind the rear muffler and one forward of the rear axle.
Trailer Hitch Installation - 2013 Honda Accord - Draw-Tite
Today, on our 2013 Honda Accord, we'll be installing a Draw Tite hitch, part number 24899. This is what our hitch will look like once its installed. Next, we're going to go ahead and give you a couple of measurements to assist you in selecting accessories for your hitch such as a ball mount, bike rack, or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is two inches. From the top of the receiver tube opening to the ground is 10 inches.Now, let's go ahead with the installation. Before we begin our install, we'll first need to lower the exhaust.
Trailer Hitch Installation - 2005 Honda Accord 4 Cylinder - Draw-Tite
Today, we're going to go over the installation on our 2005 Honda Accord, on our draw tight, hitch part number 24787. There is a difference in installation between a four and a six-cylinder, so we were going over the four-cylinder model today.Now, before we begin our installation, there are a couple of measurements that may help you in selecting the proper bike rack or cargo carrier. From the top of the receiver opening to the ground is 12-and-a-half inches, and from the center pin to the edge of the bumper is four-and -three quarters inches. To begin with, we need to get the exhaust out of the way, so we'll spray a little lubricant on the rubber boots and pry them out of the way, lowering the exhaust to make it easier to get to the bolt hole. Sometimes, a pry bar and using a small block of wood will help aid in this removal.Now that the exhaust is out of the way, we'll show you where the location for the bolt holes will be. There's one on each side, as well as using the tow hook.
Glacier Square-Link Snow Tire Chains Review - 2013 Honda Accord
Today on our 2013 Honda Accord, we'll be test fitting the Glacier square link snow tire chains, part number PWPLC1138. We'll be test fitting these tire chains on tire size 205/65/16. To begin our test fit, we'll lay the chain flat out on the ground to undo any kinks or tangles. This will ensure that the tire chain will fit correctly around the tire. Now for today's demonstration, our vehicle is on a lift to show you the connection points in a little bit more detail. We'll now drape the tire chains over the tire, making sure they are centered and the hooks are facing out so that we don't damage the outer wall of the tire.
Glacier Cable Snow Tire Chains Review - 2013 Honda Accord
Today on our 2013 Honda Accord, we'll be test fitting the Glacier cable snow tire chains, part number PW1038. We'll be test fitting these tire chains on tire size 205/65/16. Now for today's demonstration, our vehicle is on a lift to give you better detail of the connection points on the tire chain. To begin our test fit, we'll first lay the chain flat out on the ground to undo any kinks or tangles. This will ensure that the tire chain will fit correctly around the tire. We'll now drape the tire chain over the tire, making sure that the hooks are facing out so that we don't damage the outer wall of the tire.
Trailer Wiring Harness Installation - 2012 Honda Accord
Today on this 2012 Honda Accord Cross Tour we're going to install part number 118500 from Tow-Ready. Our first step is to go ahead and remove all floor coverings and the center storage bin. Now to remove the drivers side cargo tray there's a small cover we have to lift up and the bolts underneath it. We'll go ahead and remove the bolt and then remove the cargo tray. After we remove the tray if you look towards the bumper underneath the carpet you should see a connector wrapped up in blue tape. We'll go ahead and release the blue tape and then pull the connector out.
Trailer Hitch Installation - 2012 Honda Accord - Curt
Today on this 2012 Honda Accord Cross Tour we're going to install part number 11002 from Curt. This is what the hitch looks like once it's installed on the vehicle. Now Ill go ahead and give you some measurements to help you out when selecting some accessories such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be 15 1/2 inches. The hitch pin hole is about 1 inch past the edge of the bumper. Now we'll go ahead and show you how the hitch is installed.
Kuat Alpha Hitch Bike Rack Review - 2010 Honda Accord
Today on this 2010 Honda Accord were going to do a test fit of part number a103-white-114 Kuat Alpha bicycle rack. A couple of things to know about this bicycle rack that it is designed for an inch and a quarter receiver hitches, both Class I and Class II. Now well start off our test fit by installing the bike rack onto the hitch and then well install the hitch pin and the lock, then well go ahead and tighten down the anti-rattle knob, and then well go ahead and get some clearance measurements. As closet point from the bike rack to the bumper will be about four inches, with the anti-rattle knob left horizontal the clearance is going to be about 10 inches to the ground or about the same as the hitch. Now well go ahead and unfold the bike rack arms to get an overall measurement, the overall length added is about 38 inches. Now well go ahead tilt the bike rack out of the way and check access to the trunk, okay that looks good.
Thule Vertex 4 Hitch Bike Rack Review - 2010 Honda Accord
Today on this 2010 Honda Accord well be test fitting the Thule Vertex Hitch Mounted Bike Carrier part number TH9029. To mount this carrier into our vehicle, well insert the shank of the carrier into the receiver tube of the hitch, well line up our hitch pinholes, thread in our anti-rattle bolt and tighten it down using a wrench. Next well go over some clearance measurements. Weve got about 9 inches of ground clearance from the bottom of the bike rack to the ground. We got 2 inches of clearance between the closest part of the vehicle and the closest part of the carrier. Overall, weve added about 13 inches of additional length to the rear of the vehicle when the carrier arms are folded down.
Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2010 Honda Accord
Today on this 2010 Honda Accord, were going to do a test fit of part number s64670 from Swagman; this is our xtc2 bicycle rack. A few things to know about this bicycle rack that it will work with an inch and a quarter receiver hitches, both class I and class II, this will also work with a two inch receiver hitch lifting clear spacer. Today well be working with a class I receiver hitch. Lets start off with test fit by installing a bike rack into the hitch, well tighten down the anti-rattle bolt and then install the safety pin on the other side and then well go ahead and get a few clearance measurements. The bike rack to the car will be about 5-1/4 inches, the ground clearance to the back will be around 13 inches, overall the length added to the vehicle will be about 22 inches. Now well go ahead and unfold the arms on the bike rack, well also lower our center post out of the way and check for access to the back of the vehicle that looks good.
Swagman Titan Hitch Bike Rack Review - 2010 Honda Accord
All right, today on this 2010 Honda Accord, we're going to do a test fit of part number S63410 from Swagman. This is their Titan Bicycle Rack. A few things to know about this bike rack that it will work with 1-1/4-inch receiver hitches both class 1 and class 2. This will also work with 2-inch receiver hitches with the included spacers. One other thing to remember also is that when you use this bicycle rack with a class 1 receiver hitch, you're limited to carrying just two bicycles and that's what we'll be working with today. We'll start off our test fit by installing the bike rack into the hitch.
SportRack EZ Hitch Bike Rack Review - 2010 Honda Accord
Today on our 2010 Honda Accord well be test fitting the Sportrack 2 Hitch Mounted Bike Carrier part number A30901. To mount the carrier to our vehicle, well insert the shank of the carrier into the receiver tube of the hitch, well line up our hitch pinhole then thread in our anti-rattle bolt. Well tighten it down using our wrench and move on to take some clearance measurements. We got about 10 inches of clearance from the bottom of the bike rack to the ground. We have 7 inches of clearance between the closest part of the bike rack and the closest part of the vehicle. Overall, weve added about 24 inches of additional length to the rear of the vehicle.
Pro Series Q-Slot Hitch Bike Rack Review - 2010 Honda Accord
Today, we're working with a 2010 Honda Accord and we're going to be test fitting the Pro Series Q Slot Platform Style Bike Carrier, part number PS63134. To mount the carrier to our vehicle, we'll insert the shank of the carrier into the receiver tube of the hitch. We'll line up the hitch pin holes, feed in our pin and secure it with a clip on the other side. Next, we'll go over some clearance measurements. We've got about 10 inches of clearance from the ground to the bottom of the bike rack. We've got about 8-1/2 inches of clearance between the closest part of the carrier and the closest part of the vehicle.
Kuat Sherpa Hitch Bike Rack Review - 2010 Honda Accord
Today on this 2010 Honda Accord, were going to do a test fit of part number S102. This is the Sherpa Bicycle rack from Kuat. A few things to know about this bicycle rack is that it will work with 1 receiver hitches both class one and class two and this will also work with 2-inch receiver hitch with the included spacer. Today well be working with the class 1 receiver hitch. Well start off our test fit by installing the bike rack into the hitch and then well go ahead and install the pin and the lock, then well go ahead and tighten the anti-rattle knob, then well go ahead and get some clearance measurements. With the bike rack folded up, this closest point to the bumper will be 1 inches.
Rain-X Latitude Wiper Blades Installation - 2001 Honda Accord
Today on our 2001 Honda Accord, well be installing the Rain-X Fusion Wiper Blade 24, part number RX880008. This will also be in conjunction with the passenger side wiper blade, the 19, part number RX880004. First well go ahead and remove the old or manufacture wiper blades and now were ready to install the new Fusion wiper blade. With the hardware already preassembled, were ready to go ahead and open up the wiper blade clip and slide the wiper blade onto the wiper arm. Once in place, well go ahead and close the clip, securing the wiper blades to the wiper arm. Now well go ahead and repeat the same process for the passenger side.
Rain-X Fusion Wiper Blades Installation - 2001 Honda Accord
Today on our 2001 Honda Accord well be installing the Rain X Latitude wiper blades, part number RX5079280. This will be the 24 inch beam style blade for the drivers side. For this application well also be replacing the passenger side which will bet eh Rain X Latitude wiper blade, 19 inch, part number RX5079276. Our first step were going to go ahead and remove the old or manufacturers wiper blade. You need to press on the locking tab and then pull down to remove the wiper blade from the wiper arm. Now we can go ahead and take our new Latitude wiper blade, line up with the wiper arm, pushing into position and locking it in place.
Rain-X Weatherbeater Wiper Blades Installation - 2001 Honda Accord
Today on our 2001 Honda Accord well be installing the Rain-X Weather Beater windshield wiper blade, 24 inch, part number RX30224. This will be the install for the drivers side. Well also repeat the same process on the passenger side with the 19 inch wiper blade, part number RX30219. First well go ahead and remove the older manufacturers wiper blade and now were ready to install the new Rain-X Weather Beater. The Weather Beater wiper blade provide ultimate visibility in wet weather. The windshield hugging frame style design applies multiple pressure points to deliver a clean wipe, with a long lasting, all natural rubber edge resists cracking, splitting and tearing.
Yakima SuperJoe Pro Trunk Bike Rack Review - 2012 Honda Accord
Today on our 2012 Honda Accord, well be test fitting the Yakima Super Joe Pro, three bike, trunk mounted bike rack, part number Y02630. Now weve already gone ahead and preset our bike rack to fit the deck lid, so were ready to fit it to the vehicle. Now well go ahead and place the bike rack on top of the deck lid, making sure that the top arm is on the top side of the deck lid and that the bottom arm is just below the license plate. With it loosely rested there, well take the two top straps and hook them on the deck lid between the window, and the deck lid itself. Well pull them semi tight, in order just to hold the bike rack in position. Well then move down to the side and bottom straps, where well hook the appropriate strap to the deck lid here on the side, just above the tail light, and on the bottom here at the deck lid, just above the bumper.
Thule Traverse Roof Rack Installation - 2012 Honda Accord
Today on our 2012 Honda Accord well be test fitting the Thule Traverse Roof Rack System using part number THLB58, TH480 and THKIT1560. Now to begin our test fit weve already preassembled the roof rack system according to the instructions found within the fit kit so were ready to fit it to the vehicle. To begin well actually take up a measurement. Well measure from the top of the windshield, back on the roof 9 and 7/8 inches. This will be the location of the leading edge of our crossbar foot on both sides. We can then place our front crossbar in the correct location and after ensuring the crossbar is in the proper location we can go ahead and use the included Accutorc tools within each foot to tighten down the feet securing our front crossbar to the vehicle.
Yakima QuickBack 2 Bike Rack Review - 2012 Honda Accord
Today on our 2012 Honda Accord, well be test fitting the Yakima QuickBack 2-Bike Trunk Mounted Bike Rack, part #Y02621. Weve already preassembled our bike rack and test fit it on the deck lid to ensure its correct fit according to the instructions for the bike rack. Were ready to fit it to the vehicle.Well simply place the bike rack on the deck lid, ensuring that the flat end of the pads are face down. Well then hook the two top straps to the deck lid between the rear window and the deck lid itself. Well pull them slightly tight just to hold the bike rack in place. Well then move to the side and bottom straps, where well hook them in the appropriate locations, the side here right above the taillight and the bottom down here at the bottom of the trunk between the deck lid and the bumper itself.
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Honda Accord
Today on our 2012 Honda Accord, well be test fitting part #TH810. This is the Thule SUP Taxi Standup Paddleboard Carrier. Now, to begin our test fit, well place our front carrier on top of a front crossbar. Well then take the rubber-coated steel straps, wrap them underneath the crossbar, and bring them back up, securing them back to the foot of the carrier. We can then turn the gray knob, tightening down the strap, securing our carrier to the front crossbar. Well now place the rear carrier on top of the rear crossbar, again making sure that the rubber-coated steel straps run underneath the crossbar, where well reattach them on the other side.
Thule MOAB Roof Top Cargo Basket Review - 2012 Honda Accord
Today on our 2012 Honda Accord, well be test fitting the Thule M.O.A.B. Roof Top Cargo Carrier, part #TH690. Now, weve already preset our basket to accommodate our crossbar spread, so were ready to fit it to the vehicle. Well place the basket on top of the crossbar, making sure that the mounting plates are directly over the top of both crossbars. Well then use the included hardware that comes with the M.O.A.B. to clamp it to both crossbars.
Thule Flat Top Ski and Snowboard Carrier Review - 2012 Honda Accord
Today, on our 2012 Honda Accord, well be test fitting part #TH92725. This is a Thule Flat Top Ski and Snowboard Carrier. Now, to begin our test fit, with our vehicle already equipped with a roof rack system, were ready to fit it to the vehicle. Well simply take the front carrier, put it over the front crossbar, and make sure that the rubber-coated steel straps go underneath the crossbar and secure them back to the foot. Well then turn the gray knob, tighten down the strap, securing the carrier to the rack. After doing this on both sides of our front carrier, were ready to move on to the rear carrier.
RockyMounts TieRod Roof Bike Rack Review - 2012 Honda Accord
Today on our 2012 Honda Accord, well be test fitting the RockyMounts TieRod Roof Mounted Bike Carrier, part #RKY1014. Now, to begin our test fit, our vehicle is already equipped with a roof rack system. Well place our bike rack on top of the roof rack, making sure that the head of the bike rack is directly over the front crossbar. Well also need to make sure that the rubber-coated steel straps are underneath the front crossbar. We can then bring them around, and after removing the cover from the head of the bike rack, well clip them into place. Well then move to the rear crossbar, where well put the clamp from the bike rack around the rear crossbar and secure it using the wing nuts included with the bike rack.
WeatherTech Front Floor Liners Review - 2011 Honda Accord
Today on our 2011 Honda Accord well be test fitting the WeatherTech Floor Liner part number, WT451481 tan in color. First, well go ahead and remove the old or manufacturers floor mats. As you can see, its easy to install. WeatherTech Liners are custom molded to precisely fit the vehicle and stay in place. The shape, channels and moldings all work to keep dirt and debris contained in the liner and off the carpeting. As you can see, it has the custom molding around the drivers seat posts and the cut out around the fuel and trunk latch and can also be easily be removed and cleaned and washed with soap and water.
Husky Front and Rear Floor Liners Review - 2011 Honda Accord
Today on our 2011 Honda Accord well be test fitting the Husky Floor Liner in the front and second row, part number HL98401, black in color. First, well go ahead and remove the old or manufacturers floor mats. Now were ready to install the Husky Floor Liner. Husky Liners are custom molded to precisely fit the vehicle to stay in place. The shape, channels and moldings all work to keep dirt and debris contained in the liner and off the carpeting. As you can see, the front row is a two-piece set and the back row is a one-piece extending all the way from the driver to the passengers side.
WeatherTech Rear Floor Liner Review - 2011 Honda Accord
Today on our 2011 Honda Accord we'll be testing fitting the Weathertech floor liner in second row, part number WT441482, black in color. This is a one piece liner and it extends all the way from the driver's side to the passenger's side. It has special moldings around the front row seat tracks and has an extended front edge for maximum protection. As you can see, it's got the raised outer lip to keep that dirt and debris contained in the liner and also offers the center hump protection. As you see, the liner's easy to instal, can also easily be removed and cleaned and washed with soap and water. And there you have it for the Weathertech floor liner, part number WT441482, black in color.
Trailer Hitch Installation - 2011 Honda Accord - Hidden Hitch
Today on our 2011 Honda Accord, we'll be installing Hidden Hitch, part number 60892. This is what our hitch will look like once it's installed. Next, we'll give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/2 inches. From the top of the receiver tube to the ground is 11-3/4 inches. This will assist you in selecting accessories such as a bike rack or cargo carrier.
Trailer Hitch Installation - 2011 Honda Accord - Draw-Tite
Today on our 2011 Honda Accord, we'll be installing the Draw-Tite Hitch, part number 24834. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/2 inches. From the top of the receiver tube to the ground is 11-1/2 inches. This will assist you in selecting accessories such as a bike rack or a cargo carrier.
Trailer Hitch Installation - 2011 Honda Accord - Draw-Tite
Today on our 2011 Honda Accord, we'll be installing the Draw-Tite Hitch, part number 24806. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 4-1/2 inches. From the top of the receiver tube to the ground is 11-3/4 inches. This will assist you in selecting accessories such as a bike rack or a cargo carrier.
Thule Doubletrack Hitch Bike Rack Review - 2011 Honda Accord
Today were going to do a test fit of the Thule double track platform style bike rack part #: th990xt on our 2011 Honda Accord. The Honda Accord were using today has an aftermarket inch and a quarter class 2 receiver hitch on it, so with the bike rack already preassembled were going to remove the 2 inch adaptor bushing from the Thule double track. To install the bike rack into the hitch were going to need to take the shank of the rack and slide it into the receiver tube of the hitch. Well line up the hitch pinhole with the hole in the shank of the bike rack and install our threaded anti-rattle pin and safety clip. With the bike rack now installed on the vehicle we can go ahead and give you a couple of measurements. From the back of the rack to the ground is 8 and inches of ground clearance.
Thule Helium Hitch Bike Rack Review - 2009 Honda Accord
Today on this 2009 Honda Accord were going to do a test fit of part number TH970XT from Thule, the Helium Bicycle Rack. One note about this bicycle rack is that it will work by 1-1/4-inch receiver hitches both class I and class II. This will also work with 2-inch receiver hitches with the included spacer. Well go ahead and start off our test fit by installing the bike rack into the hitch. And then we'll go ahead and insert the anti-rattle pin. We'll give it a turn since it has a key to it and then we'll pull back on it and then tighten down the anti-sway device.
Thule Doubletrack Hitch Bike Rack Review - 2009 Honda Accord
All right, today on this 2009 Honda Accord were going to do a test fit of part number TH990XT from Thule, the Doubletrack Platform Style Bike Carrier. One quick note about this bike rack is that it will work with 1-1/4-inch receiver hitches both class I and class II and this will also work with 2-inch receiver hitches with the provided spacer. Now, we'll go ahead and start our test fit by installing the bike rack into the hitch. Well tighten down the anti-rattle bolt and put the lock on the other side. Alright, next well go ahead and give you some measurements on clearance between the bike rack and the car. As closest point to the bumper, we're looking at 3-3/4 inches.
Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2009 Honda Accord
Alright, today on this 2009 Honda Accord, we're going to do a test fit of part number S64670 from Swagman, the XTC-2 Bike Rack. Well start off by installing the bike rack into the hitch and we'll tighten down the anti-rattle pin and put the safety clip on the other side. Next, we'll give you some measurements on clearance between the bike rack and the car. As closest point to the bumper it's going to be 6-1/2 inches. Alright, ground clearance at the lowest point will be 10 inches, ground clearance of the back of the rack will be 13-3/4 inches. Alright, let's go ahead and unfold the rack and show access to the trunk area.
SportRack EZ Hitch Bike Rack Review - 2009 Honda Accord
Alright, today on this 2009 Honda Accord we're going to do a test fit of part number A30901 from SportRack. One quick note about this bike rack is this will work on 1-1/4-inch receiver hitches both class 1 and class 2. This will also work with 2-inch receiver hitches with the included spacer. Ok, we're going to start off our bike rack installed into the hitch. We'll go ahead and install the anti-rattle bolt and tighten it down, and then we'll install the safety pin on the other side. Now, we'll go ahead and give you some clearance measurements between the bike rack and the car.
Rhode Gear Highway Hitch Bike Rack Review - 2009 Honda Accord
Alright, today on this 2009 Honda Accord were going to do a test fit of part number RG8015220 from Rhode Gear. This is the Highway 2 Bike Carrier. Ok, well start off our test fit by installing the bike rack into the hitch and then well go ahead and tighten down the anti-rattle bolt and put the safety pin on the other side. One quick note about this bike rack is that it will work with 1-1/4-inch receiver hitches both class I and class II and also work with 2-inch receiver hitches with the provided spacer. Now, I'll give you some measurements on clearance between the bike rack and the car. Between the bumper and the bike rack will be 6-1/4 inches, ground clearance will be 9-3/4 inches.
Trailer Hitch Installation - 2011 Honda Accord
Today well be working on a 2011 Honda Accord.Were gonna install a Curt Hitch part number c11085.Here are a couple of measurements that will assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost part of the bumper is 3 inches. From the top of the receiver tube to the ground is 11 inches. This will assist you in selecting accessories such as a draw bar, a bike rack or a cargo carrier. Now lets go ahead with the installation.Our first step will be to remove the two rear exhaust hangers. To give us a better view, Im actually gonna remove three most rear hanger but before we can do that, Im gonna hang a safety strap just to hold the exhaust from falling any further than I wanted to.
Trailer Hitch Installation - 2010 Honda Accord
Today on this 2010 Honda Accord, were gonna install part number 24834 from Draw-Tite. This is also applies to part number 60236 in Hidden Hitch.This is what the hitch looks like once its installed in the vehicle. Next, well give you some measurements thatll help you out in selecting some accessories such as the ball mount, a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground on this particular vehicle is going to be 12 inches. From the center of the hitch pinhole to the outside edge of the bumper is going to be about 6 inches. Now well go ahead and show you how the hitch is installed in the vehicle.The first thing we need to do is go ahead and lower the exhaust out of the way because whats gonna happen is the hitch is gonna mount on the frame above the exhaust.
Rhode Gear Highway Hitch Bike Rack Review - 2011 Honda Accord
Today, we're going to show you how the Rhode Gear Highway 2 Bike Carrier, product number RG8015220, looks and fits on our 2011 Honda Accord. Our Honda Accord is equipped with an aftermarket inch and a quarter class 2 trail hitch so we'll need to remove the 2-inch adapter from our Rhode Gear rack. To install the rack, we simply insert the shank of the rack into the receiver of the hitch. We'll line up the threaded hole in the rack with the pin hole in our hitch, and install the anti-sway bolt and tighten it down. After we tightened down our anti-rattle bolt, we'll go ahead and install our safety clip. With the rack now installed, we'll go ahead and give you a couple of measurements.
Thule Helium Hitch Bike Rack Review - 2011 Honda Accord
Today we're going to show you how Thule Helium Aluminum 2 Bike Carrier part number TH970XT looks and fits on our 2011-Honda-Accord. The Honda-Accord we're using today has an 1"-1/4 Class 2 hitch installed on it. So we have to remove the 2'' adapter bushing in the bike rack. To install the bike rack on to trailer hitch we simply take the shank and insert into the receiver. We'll align the hole in the bike rack with the receiver pin on the trailer hitch and then install the safety pin. Next we'll turn down the anti-sway knob on the back of the bike rack.
Trailer Hitch Installation - 2002 Honda Accord
Today on this 2002 Honda Accord were going to be installing Hidden Hitch part number 60913, and this installation will also apply to Draw Tite Hitch part number 24791. Before we get started with our installation we are going to show you a couple final install hitch dimensions which will make choosing your hitch accessories a little bit easier. From the top of the receiver tube opening is going to measure 10-3/4 inches and from the center of the pin hole to clear the rear edge of the bumper is going to measure approximately 5 inches, and now we will go ahead and move on to our installation. Starting off up underneath the vehicle we want to go ahead and first point out the mounting holes that we are going to be using to attach the hitch to the vehicle. Starting over here on the drivers side of the vehicle, just forward of the trunk well on the frame itself we have an existing hole here. If we move towards the center of the vehicle on the back side of the spare tire well weve got an existing tow hook here that will provide our center attaching point for the hitch.
Trailer Hitch Installation- 2004 Honda Accord
Today we are working on a 2004 Honda Accord. We will be installing Curt hitch part number 11327. Here are a couple of measurements that will assist you in ing accessories for your new hitch. From the center of the hitch pin hole to the outermost point of the bumper is 3- ½ inches. From the top of the receiver tube to the ground is 11- ½ inches. This will assist you in ing accessories such as a draw bar, bike rack, or cargo carrier. Now let us go ahead with our installation. We need to lower the exhaust to install the new hitch. Before we take our exhaust hangers off, what we want to do is take a strap to support the exhaust. 0:42
Rhino-Rack Aero Roof Rack Installation - 2010 Honda Accord Coupe
Today we are going to show you a complete Rhino roof rack for a 2010 Honda Accord Coupe. We will be using clamp kit part number DK151 and a crossbar and foot kit, part number DA126.The first step is some small assembly on the feet. Locate the M6 by 25 millimeter security screw, the spring washer and the flat washer, as well as the M6 flat nut. Take the M6 screw, slide on the spring washer and the flat washer. Com back to the foot and slide it up through the hole so that the threads are sticking out of the top of the foot. Loosely thread the M6 square nut on the top. This is going to be hole the foot attaches to the crossbar. Locate the M8 by 50 millimeter security bolt and the M8 pivot nut. On the back side of the foot, push the pivot nut into position and make sure the angled face faces outward. Back on the front side, again we are just going to hand thread the M8 security bolt. Repeat this assembly process for the other three feet. 1:05
Trailer Hitch Installation - 2006 Honda Accord
Today we are going to be installing hitch part number 24787 from Draw-Tite on a 2006 Honda Accord. This installation will also apply to Hidden Hitch part number 60953. We are underneath the vehicle. The first thing we want to do to gain access to the frame rail is to go ahead and lower the exhaust down from the passengers side frame rail. There are actually two hangers that we are going to need to remove to lower the exhaust down. The one here on the outboard side, about midway up the muffler here, that is going to need to be pried off. And I definitely recommend to spray it down with some form of spray lubricant, like a WD-40. It makes the removal a lot easier. And the second exhaust hanger that we are going to need to lower is a little bit forward here of the muffler, right dead center of the car.
Trailer Wiring Harness Installation - 2006 Honda Accord
Today we are going to be installing wiring harness part number 118302 on a 2006 Honda Accord. We are inside the trunk area here. The connection points are actually located behind the tail light assembly, so we are going to need to remove this rear threshold piece. There are push rivets located here that are holding the threshold piece on. I am going to take a flat-bladed screwdriver and just gently pull up. OK, next I am going to go ahead and remove the carpeting. To do so, there are two Phillips-head screws that we are going to take out. We are going to remove the plastic plugs that are in here as well, and that will allow us to pull the carpeting back here. So here on the drivers side we are going to go ahead and make all three of our connections.
Trailer Hitch Installation - 2005 Honda Accord
The first thing we need to do is remove the rubber hangers holding up the exhaust. Theres one here in the center of the vehicle and theres a secondary hanger on the outside of the frame and you need to remove that one as well. This will allow the exhaust to come down so you can access this hole here. The next step is to install the bolts into the frame through the existing hole. You want to use the bolt leader thats provided, wrapping the the threads around the bolt. You slide the block onto it as well and feed it up into the hole, and pull the bolt back down through. That locks it into position. Now well repeat that and do the same thing on the other side. After we get the bolts into the frame well mount the hitch into position. After we get the two mounting frame bolts into place we want to install the mounting bolt into the tow hook.
