Yakima HighLite 2 Hitch Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, we'll be test fitting the Yakima Highlite Aluminum 2 Bike Carrier, Part Number Y02438. Now to begin our test fit, we'll slide the shank of the carrier into the opening of the hitch, align up our pinholes, we'll insert the pin through the pinhole and turn the black knob at the back carrier to engage our anti-rattle device. Now, we'll go over a few clearance measurements to see how the bike carrier and this vehicle will fit together. There are about 5-1/2 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier is about one inch. With the the cradle arms folded down, we've added about 7 inches to the overall length of the vehicle.
Thule Raceway Trunk Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger we will be test fitting the Thule Raceway 2 Bike Carrier Trunk Mount part number th9001. Now before we begin our test fit, we will first need to check to Thule Fit Guide or the included instructions to determine the number that our fit dial needs to be at. We will set our fit dial to number seven. Place the carrier onto the vehicle. Put the top hooks to the top part of the trunk. The bottom hooks to the bottom part of the trunk and turn the dials on the left and right hand side of the carrier to tighten it down and secure it to the vehicle.
Pro Series Eclipse 4 Hitch Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, we will be test fitting the Pro Series Eclipse 4 Bike Carrier part number 63124. Now to begin our test fit, we will slide the shank of the carrier into the opening of the hitch, align up our pinholes, thread our anti-rattle bolt through the pinholes and tighten with a wrench. Now we will go ahead and go over a few clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 6 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 1/4 inches. We've added about 27 inches to the overall length of the vehicle.
Hollywood Racks Traveler 5 Hitch Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, we will be test fitting the Hollywood Racks Traveler 5 Bike Carrier part number hr9200. Now to begin our test fit, we will slide the shank of the carrier into the opening of the hitch, align up our pinholes, thread our anti-rattle bolt through the pinholes and tighten with a wrench. Now we will go ahead and go over a few clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 6 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 7 inches. With the cradle arms folded down, we've added about 11 inches to the overall length of the vehicle.
Hollywood Racks Traveler Hitch Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, we will be test fitting the Hollywood Racks Traveler 4 Bike Carrier part number hr8500. Now to begin our test fit, we will slide the shank of the carrier into the opening of the hitch, align up our pinholes, thread our anti-rattle bolt through the pinholes and tighten with a wrench. Now we will go ahead and go over a few clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 6 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 1/2 inches. With the cradle arms folded down, we've added about 5 inches to the overall length of the vehicle.
Yakima DoubleDown Ace Hitch Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, well be test fitting the Yakima Doubledown Ace Four bike carrier, part number y02451. Now to begin our test fit well slide the shank of the carrier into the opening of the hitch, align up our pin holes, insert our pin into our pin hole, and turn the black knob to engage the anti-rattle device. Now well go ahead and go over a few clearance measurements to see how the bike carrier and this vehicle will fit together. Theres about six inches of ground clearance, the closet part of the vehicle to the closet part of the carrier is about two inches. With the cradle arms folded down weve added about seven inches to the overall length of the vehicle. With the cradle arms folded out weve added about 31 to the overall length of the vehicle.With this bike carrier and this vehicle you can access the cargo area with the mast of the carrier in its upright position or we can lift up on the red knob and tilt the mast down, this will also allow you to have access to your trunk.
Thule Passage Trunk Mounted Bike Rack Review - 2012 Dodge Charger
Today on this beautiful day here at Etrailer.com, we have a 2012 Dodge Charger that well be test fitting the Thule Passage two bike carrier trunk mount, part number th910xt. Now before we begin our test fit well first need to check the Thule fit guide or the included instructions to determine what number our fit dialing needs to be at. Well set the fit dial to seven according to the thick guide included in the instructions. Place the carrier onto the vehicle. Well put the top hooks to the top part of the trunk, the side hooks to the side part of the trunk above the taillight, and the bottom hooks to the bottom part of the trunk. Well then tighten down the straps to secure the carrier to the vehicle.
Thule Hitching Post Pro Hitch Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, well be test fitting the Thule Hitching Post Pro, part number th934xtr. To begin our test fit well slide the shank of the carrier into the opening of the hitch, line up our pin holes, thread our anti-rattle bolt through the pin holes, and tighten them with a wrench. Now well go ahead and go over a few clearance measurements to see how the bike carrier and this vehicle will fit together. Theres about six inches of ground clearance. The closet part of the vehicle to the closet part of the carrier is about five inches. With the cradle arms folded down weve added about 14 to the overall length of the vehicle.
Thule Apex 4 Swing Hitch Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, well be test fitting the Thule Apex Swing four bike carrier, part number th9027. Now to begin our test fit well slide the shank of the carrier into the opening of the hitch, line up our pin holes, insert the pin through pin holes, and turn the black knob to engage our anti-rattle device. Now well go ahead and go over a few clearance measurements to see how the bike carrier and this vehicle will fit together. Theres about six-and-half inches of ground clearance. The closet part of the vehicle to the closet part of the carrier is about quarter of an inch. With the cradle arms folded down weve added about nine inches to the overall length of the vehicle.
Swagman Titan Hitch Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, well be test fitting the Swagman Titan four bike carrier, part number s63410. Now to begin our test fit well slide the shank of the carrier into the opening of the hitch, line up our pin holes, thread our anti-rattle bolt through the pin holes, and tighten them with a wrench. Now well go ahead and go over a few clearance measurements to see how the bike carrier and this vehicle will fit together. There is about six inches of ground clearance. The closet part of the vehicle to the closet part of the carrier is about five inches. Weve added about 16 to the overall length when the cradle arms are folded down.
SportRack EZ Hitch Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, well be test fitting the Sport Rack two bike carrier, part number a30901. Now to begin our test fit well slide the shank of the carrier into the opening of the hitch, line up our pin holes, run our anti-rattle bolt through the pin holes, and tighten them with a wrench. Now well go ahead and go over a few clearance measurements to see how the bike carrier and this vehicle will fit together. Theres about six inches of ground clearance. The closet part of the vehicle to the closet part of the carrier is about four inches. Weve added about 21 to the overall length of the vehicle.
Softride Dura Hitch Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, well be test fitting the Softride Dura Parallelogram Tilting four bike carrier, part number sr26247. Now to begin our test fit well slide the shank of the carrier into the opening of the hitch, line up our pin holes, thread our anti-rattle bolt through the pin holes, and tighten them with a wrench. Now well go ahead and go over a few clearance measurements to see how the bike carrier and this vehicle will fit together. There is about six inches of ground clearance. The closet part of the vehicle to the closet part of the carrier is about one and half inches. Weve added about 33 to the overall length of the vehicle.
Hollywood Racks Sport Rider SE2 Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, well be test fitting the Hollywood Racks Sport Rider SE2 two bike carrier platform style, part number hr1450. To begin our test fit well slide the bike rack shank into the opening of the hitch, line up our pin holes, slide our pin through the pin hole, secure the lock on the other side, and turn the black handle at the back of the carrier to engage our anti-rattle device. Now well go ahead and go over a few clearance measurements to see how the bike carrier and this vehicle will fit together. Theres about six inches of ground clearance. The closet part of the vehicle to the closet part of the carrier is about three inches. Weve added about 22 to the overall length of the vehicle.
Hollywood Racks Baja 3 Trunk Bike Rack Review - 2012 Dodge Charger
Today on our 2012 Dodge Charger, well be test fitting the Hollywood Racks Baja 3 Bike Carrier Trunk Mount, part number HRB3. Now to begin our test fit, well set the carrier onto the vehicle and adjust the arms of it using the black levels on the left and right side of the carrier. Once we get it adjusted we can tighten down the levers, put the top strap to the part of the trunk, the side straps to the side part of the trunk above the taillights and the bottom hooks to the bottom part of the trunk. Well then tighten down the straps to secure it to the vehicle. Now were ready to load our bike. Well undo the cradle straps and set the bike into the frame cradle and secure it with the straps.
Trailer Hitch Installation - 2007 Dodge Charger - Hidden Hitch
Today on our 2007 Dodge Charger, well be installing Hidden Hitch part number 90209. Note, once installed, this is what the hitch will look like. Next well go ahead and get you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch pinhole to the outermost edge of the bumper is 6 inches. From the top of the inside of the receiver tube opening to the ground is 10 inches. This will assist you in selecting accessories such as a bike rack or cargo carrier.
Trailer Hitch Installation - 2012 Dodge Charger - Curt
Today on this 2012 Dodge Charger V6 model, were going to install part number C12064 from Curt. This is what the hitch looks like when its installed on the vehicle. Next well give you some measurements that will help you out in selecting some accessories, such as a bicycle rack or a cargo carrier. From the top of the receiver opening down to the ground will be about nine and a quarter inches. From the center of the hitch pin hole to the edge of the bumper will be about seven inches. Now well go ahead and show you how the hitch is installed.
Thule Raceway Trunk Bike Rack Review - 2007 Dodge Charger
Today, on a 2007 Dodge Charger we'll be test-fitting the Thule Race Way 2-Bike Carrier Trunk Mount, part number TH9001. Before we begin our test-fit, we're first going to check the Thule fit guide or the included instructions to determine what number our fit dial should be at. We'll set out fit dial to seven, set the carrier unto the vehicle.We'll put the top hooks to the top part of the trunk, the bottom hook to the bottom part of the trunk, and we'll use the knobs on the left and right side of the carrier to tighten down and secure it to the vehicle. Once the carrier secured to the vehicle, we're ready to load our bike. We'll lift up the grey handle, swing the cradle arms out, push the handle back down to secure the cradle arms in position, and undo the cradle straps. We'll set the bike into the frame cradles and secure with the straps.
Yakima Q Tower Roof Rack Installation - 2007 Dodge Charger
Today on our 2007 Dodge Charger, we'll be testing the Yakima Round Crossbar Roof Racking System, Part Numbers Y00409, Y00699, Y00683 and Y00124. Now, with the roof rack already assembled, we'll go ahead and open the front driver side and passenger side door and set the front crossbar on to the vehicle. We will then check the Yakima fit guide for the included instructions to determine the measurement from the front part of the glass to the first part of the q tower. Our measurement is 8 inches. We'll measure the passenger side, first part of the glass to the first part of the tower, 8 inches then we'll move to the other side where we will do the same. We need to make sure that we get the crossbar perpendicular to the vehicle to ensure the tower gets a good fit to th vehicle.
Thule AeroBlade Traverse Roof Rack Installation - 2012 Dodge Charger
Alright, today on this 2012 Dodge Charger, we're going to do a test fit of the Thule Roof Rack System. Today, we'll be using the Thule AeroBlades, part number THARB53, the Rapid Traverse Foot Pack, part number TH480R and a fit kit, part number THKIT1604. We'll start off our test fit with our load bars already assembled according to instructions so it's just a matter of placing them on the roof. With the doors opened, we can place the first bar on the roof of our Charger. Now, to place our load bar in the correct spot, we're going to measure from the leading edge of the foot pack to the edge of the windshield. And you always want to go by your instructions, but in this case, we'll be using a measurement of 8-1/4 inches.
Thule Flat Top Ski and Snowboard Carrier Review - 2012 Dodge Charger
Alright, today on this 2012 Dodge Charger, we're going to do a test fit of part number TH92725, the Thule Flat Top Ski and Snowboard Carrier. Our Charger already has a Thule Roof Rack installed using AeroBlade crossbars and our Flat Top is already assembled according to the instructions. So what we have to do is fit it on top of our rack. We'll start off our test fit by placing the first half of the ski rack on the rack and run the straps underneath the crossbar and to the clip on the other side. Then we'll loosely tighten them down. Once it's loosely installed, we can move it around into the position we want.
Thule Domestique Roof Bike Rack Review - 2012 Dodge Charger
Alright, today on this 2012 Dodge Charge, we're going to do a test fit of part number TH513, the Thule Domestique Bike Carrier. We'll start off our test fit with our bike carrier already assembled according to instructions, so all we have to do is put this on our roof. Our Dodge Charger has already been equipped with a roof rack using the Thule AeroBlade system. We'll start our test fit by taking the bike rack and placing it on top of the roof rack. We'll start with the front clamp and then move the rear clamp into place. We'll take a second and make sure the bike rack is sitting where we want to and then we can go ahead and tighten it down for good.
Thule Vertex 4 Hitch Bike Rack Review - 2012 Dodge Charger
All right today in this 2012 Dodge Charger, we're going to do a test fit of part number TH9029 from Thule; the Vertex Four Bicycle rack. A few things to know about this bicycle rack that it will work with inch and a quarter receiver hitches both class one and class two. This will also work with two-inch receiver inches with the provided spacer. And one other thing to know that when you use this bicycle rack for class one receiver hitch, you're limited to carrying just two bicycles. Now we'll start off our test fit by installing the bike rack into the hitch, and then we'll go ahead and tighten down the anti-rattle bolt. All right, now we'll go ahead and get some clearance measurements.
Thule Traverse Roof Rack Installation - 2012 Dodge Charger
All right today on this 2012 Dodge Charger, we're going to do a test fit of the Thule Roof Rack System. We'll be using the Thule Square Load Bar, part number THLB58, part number TH480, the traverse flip pack and part number THKIT1604 Thule fit kit. Now we're going to start off our load bars already assembled according to instructions, so all we got to do is put them on the roof. We'll start with the front crossbar and open up the front doors and then place the bar onto the roof. To place the bar correctly, we'll measure from the edge of the windshield to the edge of the foot pack. I always go by the instructions, but on this particular test fit, we'll be using a measurement of eight and a quarter inches.
Thule SUP Taxi Stand-Up Paddleboard Carrier Review - 2012 Dodge Charger
Today on this 2012 Dodge Charger, we're going to do a test fit of party number TH810; the Thule SUP Taxi. Now our charger has already been equipped with a roof rack system using a Thule AeroBlade Crossbars. We'll start off our carrier already assembled according to the instructions, so all we have to do is put it on the roof rack. We'll take our first carrier, place it up on the roof rack and then wrap the straps underneath the AreoBlade bar and then the clips on the other side. Once we have it loosely attached, we'll go ahead and move it into its final position and tighten it down for good. Okay, we got the first half in placed and we'll go ahead and move on to the second half, we will repeat the same steps that we used to install the first half of the carrier.
Thule Sidearm Roof Bike Rack Review - 2012 Dodge Charger
Today we have with us the 2012 Dodge Charger and we'll be test fitting the Thule Sidearm Roof Mounted Bike Carrier part # TH594XT. We already have our bike carrier assembled and we're ready to mount it up on top of our vehicle. We'll place the head of the bike carrier over our frontload bar. We'll use the two clamps with the wing nuts to tighten it down. And the rear, we'll fit the rear clamp around the rear bar and again we'll use the wing nuts to tighten clamp down. With our bike rack secured on the roof rack, we're ready to load it up.
Thule Echelon Roof Bike Rack Review - 2012 Dodge Charger
All right, today on this 2012 Dodge Charger, we're going to do a test fit of part # TH518 the Thule Echelon Roof Mounted Bike Rack. Okay, to start off or test it, we'll have our bike rack assembled according to the instructions so all I have to do is put up on the roof rack. We'll lay the bike rack on the crossbar first then we'll slide the clamp underneath and around the little bar. Then we can tighten down two Allen screws. Once we have everything loose and installed, we'll go ahead move the bike rack into position that we want and make sure it's centered on the vehicle. When bike rack lined up in center, we can go ahead and tighten it down for good.
Thule Apex 4 Hitch Bike Rack Review - 2012 Dodge Charger
All right, today in this 2012 Dodge Charger, we're going to do a test fit of part # TH9025 from Thule, the Apex 4 Bike Carrier. Now we're going to start of our test fit by installing a bike rack into the hitch. We'll open up the integrated hitch pin. Make sure your pin latches in and then go ahead and tighten down the anti-rattle knob. All right, now I'll go ahead and get a couple clearance measurements. Clearance from the bike rack to the bumper in the car is about one inch and ground clearance is only about seven inches.
Swagman Fork Down Roof Bike Rack Review - 2012 Dodge Charger
Today we have a 2012 Dodge Charger and we're going to be test fitting the Swagman Fork-Down Roof Mounted Bike Carrier. We've already got our carrier assembled and now we're ready to mount it up on our vehicle. To mount the carrier, we'll place the head of the rack on top of our frontload bar. We'll fit the U bolts around our load bar and back through the head of the platform and we'll tighten it down with the wing nuts. Put the front half of our carrier secured, we can move to the back. We'll position the U bolt in the rear of the carrier over our rear load bar and use the clamp bar and the two wing nuts to tighten it down to our rear bar.
SportRack Nomad Roof Bike Rack Review - 2012 Dodge Charger
Today on this 2012 Dodge Charger, we're going to be test fitting the Sportrack Nomad Roof Mounted Bike Carrier part # ABR611. To mount the carrier up on our vehicle, we'll place the head of a bike rack on top of our frontload bar. We'll fit the U bolts around the underside of our load bar and we'll tighten down with the wing nuts on top. In the rear, we'll fit the rear clamp around our rear load bar and we'll again use the wing nuts to tighten it down. Once we've done that, we're ready to load our bike. First we'll undo the wheel straps sat either end of the bike carrier.
RockyMounts TieRod Roof Bike Rack Review - 2012 Dodge Charger
All right, today this 2012 Charger, we're going to do a test fit of part # RKY1014 the RockyMounts TieRod Bike Carrier. We're going to start with our test fit with the bike rack assembled according to instructions. So we're going to simply place it on a roof rack and begin our test fit. We'll begin our test fit by installing the carrier on the front crossbar and make sure the straps wrap around from underneath and into the clip in the front. With that loosely attached, we'll go ahead and run the clamp in the rear around the back crossbar and then tying it down but still keeping it loose so we can move it around. Now, I'll take a second and make sure the bike rack is centered with the vehicle before tightening it down for good.
Trailer Hitch Installation - 2012 Dodge Charger
Today on this 2012 Dodge Charger, well install part number 13093 from Curt. This is what the hitch looks like when its installed on the vehicle. Next, well go ahead and give you some measurements that will help you out in selecting some accessories such as a ball mount, bicycle rack, or a cargo carrier. From the center of the hitch pin hole to the outside edge of the bumper is going to be 7-1/2 inches. From the top of the receiver opening down to the ground is going to be 8-1/4 inches. Now, Ill go ahead and show you how the hitch is installed.
Highland Rear Floor Mats Review - 2012 Dodge Charger
Alright today, on this 2012 Dodge Charger, we are going to do a test fit part number 44031 from Highland. This is a semi-costum fit floor mat for the second row. We'll be working with the tan color today. This is also available in gray as 45031 and black as part number 46031. These mats are created from a durable rubber and it won't crack or stiffen. It is designed to contour to the floor of the vehicle.
Highland Front Floor Mats Review - 2012 Dodge Charger
Alright today, on this 2012 Dodge Charger, we are going to do a test fit of our Highland floor mats. We'll work with part number 44022 in tan color. This is also available as black as part number 46022 and gray as 45022. We'll start off by removing the old floor mats and install the new floor mats. These mats are created from a durable rubber and they will not crack or stiffen. They are designed to contour to the floor of the vehicle. They are unaffected by chemicals or mud. The shape and the channels inside the floor mat help keep dirt and debris contained in the mat and not in your carpet.
Yakima Q Tower Roof Rack Installation - 2011 Dodge Charger
Today on this 2011 Dodge Charger were going to do a test fit of a Yakima roof rack system. Were using Yakimas Q Towers with the 58-inch load bars. Okay, were going to start off with the roof rack bars already assembled according to the instructions and were going to open up the car doors on our charger. Well go ahead and place the first crossbar on the roof. What were going to do is place it toward the front windshield for now, then next were going to measure out from the windshield to the leading edge of the tower, in this case is going to be eight inches. You always want to refer to the instructions for measurements.
Trailer Hitch Installation - 2011 Dodge Charger
Alright today on this 2011 Dodge Charger, were going to install part number 13093 from Curt. Alright this is what the hitch looks like when its installed on the car and next well give you some measurements to help you out in selecting some accessories.Have the receiver opening down to the ground and this car is going to be 9 inches and from the center of our hitch pin hole to the outside edge of the bumper is going to be 8 inches. First were going to show you how its installed. First thing we need to do is actually lower part of the exhaust and remove part of the exhaust to make it easier to install the hitch. So were going to put down this clamp right here, put some lubricant, were going to pry the clamp open just a little but, just so theres enough to make it loose. Ok, then well leave everything alone for now.
Trailer Wiring Harness Installation - 2006 Dodge Charger
Today on this 2006 Dodge Charger, we will be installing wiring harness part number 118404. We are in the trunk area of the Charger here and we want to go ahead and locate the port for our wiring harness. The ports are located directly behind the tail light assemblies here inside the trunk compartment. So we need to go ahead and remove the interior carpeting here to gain access to those. To do that we just need to remove the screw here on both sides of the vehicle and we just pull that back. You see once we do that, right in the back of the tail light assembly is our connection point. As you see there is a red tab here at the top. We want to push that over and then there is also a button here at the top we push that in and disconnect the two like so. 00:41
Trailer Hitch Installation - 2006 Dodge Charger
Today on this 2006 Dodge Charger we will be installing Curt hitch part number 13465. We are underneath the vehicle and before we get started we need to go ahead and lower the exhaust off of both frame rails so that we can gain access to the existing weld nuts in the frame. There are two hangers per side that we are going to remove the exhaust off of. One here and one here on the driver side and then one here and here on the passenger side. And on some models it may be necessary to go ahead and remove the third hanger as well to gain just a little bit more room.
Trailer Hitch Installation - 2007 Dodge Charger RT
Today we are going to install part number 13465 from Curt on a 2007 Dodge Charger RT. The first thing we need to do is lower the exhaust. We have got two points we need to lower: one here, and one in the back. Now, we can simply unbolt those from the frame and it will come down. And we will do that on both sides. And also, for added safety, and to keep the stress down on the exhaust, we added this safety strap here. And one other point we need to disconnect will be right here, that is going to be right in front of the converter here. And basically we are going to just take this off and let the exhaust fall down as much as possible, limited by the strap, of course. And that will give us plenty of working room. Now we will take down this side of the exhaust. All right, and now we will do the passengers side.
Trailer Wiring Harness Installation - 2007 Dodge Charger
Along with your custom receiver hitch for the Dodge Charger you will also need a wiring connector when pulling a trailer. We offer a custom wiring harness that requires no cutting or splicing and will provide a flat four pole connector. This will power the trailers running lights, brake lights and turn signals allowing you to safely and legally tow your toys, boat and trailer. You may also want this to power lights on a cargo trailer or to use a light up receiver hitch cover.
