Trailer Hitch Installation - 2007 Chrysler 300 - Curt
Today on our 2007 Chrysler 300, we will be installing Curt Hitch, part number C12240. Before we begin our installation, here are a few measurements to help you on selecting accessories such as a bike rack or a cargo carrier. From the center of the hitch pin hole to the outer most part of the bumper is 7 inches. From the top of the receiver tube to the ground is 12 inches. Now lets go ahead with our install. Before we begin our installation, we will need to lower our exhaust. Well first put a safety strap underneath the vehicle to hold the exhaust while we undo the mounting location. On the two rear most isolators, we can go ahead and undo the bolts holding the isolators to the vehicle.
Trailer Hitch Installation - 2005 Chrysler 300 - Curt
Today on our 2005 Chrysler 300, we'll be installing the CURT hitch, part number 13465. This is what our hitch will look like once it's installed. Next, we'll go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch. From the center of the hitch-pin hole to the outermost edge of the bumper is 6 3/4 inches. From the top of the receiver tube opening to the ground will be 10 1/4 inches. This will assist you selecting accessories, such as a drawbar, a bike rack, or cargo carrier.
Trailer Hitch Installation - 2007 Chrysler 300 - Hidden Hitch
Today on our 2007 Chrysler 300, well be installing Hidden Hitch, part number 90209. Now before we being our installation, heres what your hitch will look like on the vehicle. Well go ahead and give you a few measurements to help when selecting accessories such as a bike rack or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 6 inches and from the top of the receiver tube to the ground is 10 inches. Now lets go ahead with our install. Now before we begin our installation, well need to lower our exhaust. Well first put a safety strap underneath the vehicle to hold the exhaust while we undo the mounting location.
Trailer Hitch Installation - 2007 Chrysler 300 - Draw-Tite
Today on our 2007 Chrysler 300, well be installing Draw-Tite Hitch, part number 36508. Now before we being our installation, heres what your hitch will look like on the vehicle. Well go ahead and give you a few measurements to help when selecting accessories such as a bike rack or a cargo carrier. From the center of the hitch pinhole to the outermost part of the bumper is 6 inches and from the top of the receiver tube to the ground is 10 inches. Now lets go ahead with our install. Now before we begin our installation, well need to lower our exhaust.
Thule Raceway Platform Trunk Bike Rack Review - 2005 Chrysler 300
Today on our 2005 Chrysler 300 well be test fitting the Thule Raceway platform style two bike carrier, part number TH9003. To begin our test fit, weve already set up our bike rack according to the instructions found within the Raceway packaging, so well begin by placing the bike rack on top of our deck lid, making sure that the bottom rests on the bumper cover. Well then take the two cables for the top and clamp them to the deck lid just behind the rear window. Well take the two lower cables and clamp them to the deck lid, here right above the rear bumper cover. We can then ratchet down all four cables, securing our bike rack to the vehicle. With our bike rack secure well now bring out our top bar clamp and make sure that its out of the way.
Thule Raceway Trunk Bike Rack Review - 2005 Chrysler 300
Today on our 2005 Chrysler 300 well be test fitting the Thule Raceway two bike carrier, trunk mount, part number TH9001. To begin our test fit, weve already preassembled the bike rack according to the installation instructions found with the Raceway. Well place our bike rack onto the deck lid, making sure its resting on the bumper cover. Well then take the two top cables and secure them to the deck lid just behind the rear window. We can then ratchet them down using the knobs on either side of the bike rack to hold it into place. Well then do the same with the two lower cables on either side.
WeatherTech Front Floor Mats Review - 2006 Chrysler 300
Today on this 2006 Chrysler 300, we're going to be test fitting part # WTW69 black in color. First we're going to remove the old and manufacturer's floor liners. Now, we're ready to install the WeatherTech floor mat. The WeatherTech floor mats are molded to fit the vehicle and stay in place. The shape, channels and moldings all work to keep dirt and debris contained in the liner and off with the carpeting. The mats are made of a flexible rubber material that won't curl, crack or harden in subzero weather.
WeatherTech Rear Floor Mats Review - 2006 Chrysler 300
Today on our 2006 Chrysler 300, we're going to be test fitting the WeatherTech Floor Mats part # WTW20TN. First we're going to remove the old and manufacturer's floor liners. Now, we're ready to install the WeatherTech Floor Mats. It's made of a flexible rubber material that won't crack, curl, or harden in subzero temperatures. Underneath the mat is an anti-skid design to prevent from shifting in your vehicle. This mat comes back with a 10-year guarantee.
Highland Rear Floor Mats Review - 2006 Chrysler 300
Today on our 2006 Chrysler 300, we're going to be test fitting the Highland floor mat in the second row; part number 46031, black in color. First, we will go ahead and remove the old or manufacturer's floor liners. Now we're ready to install the highland floor mat. The all-weather Highland mats are made of a durable pliable rubber. They won't crack or stiffen in extreme temperatures. Often will conform to fit the contours of the vehicle's floor board.
Highland Front Floor Mats Review - 2006 Chrysler 300
Today on our 2006 Chrysler 300, we're going to be test fitting the Highland floor mats in the front row; part number 44022, tan in color. First, we will go ahead and remove the old or manufacturer's floor liners. Now we're ready to install the highland floor liners. The highland mats are made of a durable pliable rubber. They won't crack or stiffen and will often conform to the contours of the vehicle's floor board. They are unaffected by extreme temperatures or dirt or debris.
Trailer Hitch Installation - 2006 Chrysler 300 - Curt
Today on our 2006 Chrysler 300, well be installing the Curt Hitch, part number 13465. This is what our hitch will look like once it's installed. Next, well give you a couple of measurements to assist you with selecting accessories for your new hitch. In the center of the hitch pinhole to the outermost edge of the bumper, is seven inches. From the top of the receiver tube, to the ground is 10 inches. This will assist you with selecting accessories, such a drawbar, a bike rack or cargo carrier.
Trailer Hitch Installation - 2007 Chrysler 300
Today on this 2007 Chrysler 300 we are going to be installing Curt hitch part number 13465. We are underneath the vehicle, the first thing we want to do is lower down the exhaust. Depending on your model you may have a single exhaust or a dual exhaust. On this particular vehicle we have a single exhaust. There is a hanger here at the rear side of the exhaust and a second one here at the forward side that we want to remove as well. If we follow forward we need to lower down these two hangers here as well. On the rear hanger some models will have this grounding strap, you want to make sure you take that off as well before you lower the exhaust down. :39
Trailer Brake Controller Installation - 2007 Chrysler 300
Today we are going to be installing Prodigy part number 90185 on a 2007 Chrysler 300. We are also going to be using the brake control wiring kit, part number ETBC7. What we are going to do is go ahead and locate a good position to mount the brake controller. We are inside the cab here, directly below the steering wheel. A good mounting location for the brake controller is typically right to the right of the steering wheel so it is within hands reach of making your adjustments. But before we go ahead and mount it I want to go ahead and locate the brake wire underneath the steering column, right above the brake pedal. This is a wire that we are going to need to tap into which is going to activate the brake controller for us. It is actually located on the brake switch and we are going to look for the wire that actually gets hot when we depress the brake pedal. There is a carpeting piece underneath here that is covering up all the wiring that is above the brake pedal. So the first thing I am going to do is to go ahead and remove that. There are two push pins: one here, and one here, that I need to remove. OK, now that we have got the carpeted piece up and out of the way, we have gone ahead and located the brake switch, which is that white box right there at the top of the brake pedal. If you follow behind that, you will locate the wiring harness that is feeding the brake switch. I went ahead and tested them and I found that the green wire with the white stripe is the wire that we are looking for that is the cold side of the brake switch - the wire that we are looking to tap into with the red wire on the brake controller. So we are going to go ahead and do that now, and then I think we will go ahead and mount the brake controller.
Trailer Hitch Installation - 2007 Chrysler 300C
Today we are going to install part number 13465 from Curt. We are going to install this on a 2007 Chrysler 300c. To begin our install, we have to lower our exhaust out of the way. We actually have to lower it down pretty good, a pretty far distance. Basically we are going to remove this hanger here, we are going to unbolt it here. We will unbolt this hanger also. Now on the back here, we will need to undo this rubber hanger here too. This whole exhaust system will be resting basically on this point right here. So it may be a good idea to throw a strap around the exhaust for safety purposes to it keep it from really falling down. It looks like we have plenty of clearance to do our work here so we do not have to undo that last strap, our last hanger, so we should be in good shape.
Trailer Wiring Harness Installation - 2007 Chrysler 300 Touring Edition
First thing we need to do is access the trunk area. Lift up the back flap here and remove the rear threshold piece, there are four pop rivets holding it in place. We pull back the threshold on the passenger side, it will reveal the connection point for the wiring harness. Once we locate the connection point we want to flip back this red tab, which is holding it in place, and push the button down on the topside and pull the connectors apart. This time we want to take the t wiring harness and plug it into this.
