Chevrolet Van owners are most interested in these products

Chevrolet Van Questions and Answers

Recommendations for Bright LED Flood Lights
You would want to look at LED utility lights. I have added a link to them for you to view. Or you might be interested in a set of LED docking lights, # DLL50CC. The light output of each light in kit # DLL50CC is 1000 candela. The literature for this set states 440 lumens per light, 880 combined.
view full answer...

What is the Inside Width of Replacement Jack Handle # DL22674 where it Attaches to the Trailer Jack
I went out to the warehouse and pulled a Replacement handle, # DL22674, to measure it for you. Where the handle bolts to the jack, the inside width is 1/2 inch. I have included a link to a video review featuring this handle for you.
view full answer...

Where Does the Trailer Wiring Harness # 118338 Connect to a 1993 Chevy Van
The Tow Ready custom fit vehicle wiring, # 118338, connects to the vehicle behind the tail lights on the 1993 Chevy vans. However, a conversion can take many forms and you might not be able to connect this harness in the same manner. I have included a link to the installation instructions for you to view.
view full answer...

Transmission Cooler for a 1988 Lazy Dave RV on a Chevy G30 Van Chassis
Transmission coolers are not vehicle specific so anyone that will fit in the space you have in the engine compartment you can use. Adding the cooler will not bypass the existing cooler which is located inside the radiator. Adding a cooler provides supplemental cooling to the factory cooler. The traditional way to install an additional cooler is in line with the factory line that leads back to the transmission. You will have one hose that goes from the transmission to the radiator and another
view full answer...

Transmission Cooler Recommendation for a 1990 Chevy G30 Motor Home with a 5.7 Liter V8
Good news, transmission coolers are not vehicle specific so you will be able to use one on your 1990 Chevy motor home. The cooler you have referenced, the Derale 8000 Plate-Fin Cooler, # D13503, is listed as a recommended cooler for the 5.7 liter Chevy motors for the 1990 model year. I have included some links to FAQ articles and a video for you that explains installation.
view full answer...

Will Tow Ready Trailer Wiring Harness # 118338 Fit a 1995 Chevy G Series Van with Step Bumper
According to Tow Ready, the manufacturer, the Tow Ready Wiring Harness, # 118338, will fit your 1995 Chevy Van, even if it has a step bumper. I have included a link to the installation details for you to view.
view full answer...

Derale D13504 Transmission Cooler Installation on a 1993 Chevy G-30 Van
There are not specific installation instructions when it comes to installing transmission coolers, but there are basic guidelines for installing one that are pretty universal. The first step for installing this Derale Series 8000 Plate-Fin Transmission Cooler Kit, part # D13504, on your 1993 Chevy G-30 van with A/C is finding the best location for mounting the cooler. If you mount the cooler in front of the radiator, you will get the most cooling efficiency from the cooler, whereas it will
view full answer...

Will Titan Aero 7500 Swing-Away Actuator # T4839300 Fit a 3 x 4 Inch Trailer Frame, Is it Weld-On
As long as the trailer frame is no greater than 3 inches wide, the Titan Aero 7500 Swing-Away Actuator, # T4839300, will fit. It is a weld-on application. The picture on the product page is a typical photo since all of the actuators in the same series look pretty much the same. This actuator is made to be used with a 2 inch ball. It has a gross trailer weight capacity of 7,500 pounds and a tongue weight capacity of 750 pounds. It is for use with drum brakes only. You may also need a Titan Hy
view full answer...

7-Way, Vehicle End, Trailer Connector Wiring Diagram
See the picture to the right for a wiring diagram of seven-way vehicle end trailer connector. If you click on it you can enlarge it. I have also included a trailer wiring FAQ page for you to check out.
view full answer...

How Should the 15K Truck and Trailer Winch # E52801 be Mounted to A Trailer
You are correct, the 15K Truck and Trailer Winch, item # E52801, is designed to be mounted to a trailer or trucks bed. The most common use is on the side of the trailer welded to the trailer frame. You see this type of application often on the sides of flat bed semi-trailers. Welding by a qualified weldor is the approved method for attaching the Truck and Trailer Winch. If you wanted to bolt the winch to the frame you would have to drill holes in the base and use bolts washers and lock washer
view full answer...

Installation of the Prodigy On a 96 Winnebago p-30 chev.
Installation of the Tekonsha Prodigy should be fairly easy with the Winnebago having a 7 -way connector installed from the factory. There should be a wiring harness under the drivers side dash that will have at least 4 wires to connect to the brake controller. I do not have vehicle specific information on the Winnebago wiring location but it should be there if it was a factory option. The wires should provide brake controller functions. If you have a GM chassis then the colors of the wires may b
view full answer...

Measurements for Adjustable RV Trailer Hitch 13703
I have obtained the measurements you have requested On the mounting brackets, the holes measure 7-1/2 inches in length and 2 inches in height (center of the hole to center). From where the bracket attaches to the frame to the top of the receiver tube, it is 6-1/8 inches. You requested a height clearance measurement; however, with this measurement, you will be able to measure your own frame and where it would clear the ground. From the back of the receiver tube to front of the receiver,
view full answer...