Chevrolet Tahoe owners are most interested in these products
change vehicle
WeatherTech Cargo Floor Liner Review - 2013 Chevrolet Tahoe
Today well be test fitting the Weathertech Cargo Liner in tan, part number WT41306 on our 2013 Chevy Tahoe. This mat is also available in gray, part number WT42306 and black part number WT40306.Before we begin our test fit, we will first need to remove the third row of seats. To do this, well start off by first folding down the back rests of the seat. After laying down the back rests of the seat, well simply pull out on the handle. Well do this for both the passenger and driver side seats of the third row.Well now place the new Weathertech Cargo Liner into the cargo area of the vehicle. You can notice that the mat is custom molded to allow for complete coverage of your trunk or cargo area.
Longview Custom Towing Mirrors Installation - 2013 Chevrolet Tahoe
Today on our 2013 Chevy Tahoe, well be testing the Longview Slide On Original Custom Towing Mirrors, part number CTM 1600.Now to begin our test fit, well slide our new Longview mirrors onto the original manufactures mirror. Note that each mirror is designed for only one side of the vehicle.Now with the mirror on, well install the brackets. Well slide the plastic piece onto the hole at the end of the mirror with the flat rounded piece at one end. Well then slide the next long plastic piece with the hook through the hole on the L-bracket. Note when tightening the knobs before the hook is secured, tighten the knobs down just a little bit to ensure the hook can get around the mirror.Well now take the hook and put it around the manufactures existing mirror. Well then tighten down the knobs to secure the Longview mirror to the manufactures mirror.
Glacier Cable Snow Tire Chains Review - 2013 Chevrolet Tahoe
Today on our 2013 Chevy Tahoe, well be test fitting the Glacier Cable Snow Tire Chains for light trucks, part number PW3027C. Well be test fitting them on 265-70-17 tires. Now this vehicle primarily rear wheel drive, so we will be test fitting the tire chains on the rear tires.To begin our test fit, well lay the chains flat out on the ground to undo any kinks or tangles. This will ensure the tire chains fit correctly around the tire. You can notice here that the yellow indicator tag determines what tire the tire chain should go on. After determining which tire chain goes on what side of the vehicle, well drape the tire chain over the tire.
WeatherTech Front Floor Liners Review - 2013 Chevrolet Tahoe
Today on our 2013 Chevy Tahoe well be test fitting the Weathertech front auto floor mats in tan, part number WT450661. To begin our test fit we will first need to remove the factory, or previously installed floor mats. We will do this for both the front drivers side and passengers side of the vehicle. Were now ready to install our new Weathertech floor mats. We will simply place the floor mat in to where the existing mat was. We will repeat this step for the other side.
Rain-X Fusion Wiper Blades Installation - 2005 Chevrolet Tahoe
Today on our 2005 Chevy Tahoe, well be installing the Rain-X Fusion windshield wiper blades, part number rx880007, 22 in length. Both the driver and passenger side will be identical. The Rain-X Fusion windshield wiper blade is a replacement all-weather wiper blade that provides superior visibility in rain, snow, and sleet. The sleek hybrid blade delivers a clean streak free wipe combining the benefits of fraying and beam style blades. With the windshield how you can design, the wiper blade has multiple pressure points along the blade with a contoured frame that conforms to the shape of your windshield. With the synthetic rubber squeegee it promises a superior wipe in all types of weather.
Putco PURE Headlight Bulbs Installation - 2005 Chevrolet Tahoe
Today on our 2005 Chevy Tahoe, well be installing the Putco Pure High Performance Halogen light bulb, part number p239006sw. This will be bulb type 9006 that will carry 55 watts at 12 volts and has a one year warranty. To replace the bulb, well simply open up the hood and then for this application we need to remove the headlight bucket. To do this well remove the two pins that secure it in position by turning the pin 45 degrees well go ahead and release it from its lock and pull up removing it. Well go ahead and work the headlight bucket out to where we get access to the wiring. Now well go ahead and take the low beam or outside light socket out of the headlight bucket by turning it, unlocking it from its tabs.
Roadmaster InvisiBrake Supplemental Braking System Installation - 2001 Chevrolet Tahoe
All right. Today, on this 2001 Chevrolet Tahoe, we're going to install part number RM-8700 from Road Master, and this is a brake kit. Okay. To start off the install, we remove the threshold and also the kick plate by the compartment brake. We lift up the trim panels in the back. We're going to route our cylinder next to the driver seat, and we will attach it later on to the metal bracket that's near a console.
Curt 20x60 Folding Aluminum Cargo Carrier Review - 2005 Chevrolet Tahoe
Today on our 1005 Chevrolet Tahoe well be test fitting the Curt 20 by 60 folding aluminum cargo carrier for two inch hitches, part number C18100. Now to begin our test fit well go ahead and slide the cargo carrier shank into the hitch, line up the hitch pin hole and install out hitch pin. We can then put the clip on the other side of the pin which will secure the cargo carrier to the vehicle. Well now go ahead and give you a few measurements. Our ground clearance here at the shank of our cargo carrier is 13 inches. With the cargo carrier folded up from the closest point of the carrier to the back of the vehicle is approximately 2 inches.
Trailer Brake Controller Installation - 2011 Chevrolet Tahoe
All right. Today, on this 2011 Chevrolet Tahoe, we're going to install Part Number 5500 from Draw-Tite. We're also going to use part number 20127 form Tow Ready, this is our universal brake control plug. What this part does, we'll plug into the port on the brake controller and it will give us pair wires to hook up to on our tow package that's on the Tahoe. Now, towing package wires are located underneath the dash to the left side of the brake pedal and they're usually tucked behind some wires. You want to look for a blue and a red wire to help identify the bundle.
Longview Custom Towing Mirrors Installation - 2011 Chevrolet Tahoe
Today on this 2011 Chevrolet Tahoe were going to do a test fit of part number CTM1600, a custom towing mirror from Longview. This part number comes with both sides. Were going to be working with the drivers side today. Well start off our test fit by sliding our towing mirror over to factory mirror. Make sure its fully seated around the factory mirror. Then we can go ahead and install our cache of hardware.
CIPA Custom Towing Mirrors Installation - 2011 Chevrolet Tahoe
Today on this 2011 Chevrolet Tahoe were going to do a test fit of part number 10901 from Cipa. This is their custom towing mirror for the drivers side. Well start off our test fit by sliding on the new Cipa mirror over the factory mirror and well go out three quarters of the way. Then well take our wedge and put it between the Cipa mirror and the factory mirror. Then well push the two together. Well make sure that the towing mirror is fully seated onto the original mirror, and then well go ahead and install the locking knob.
WeatherTech Cargo Floor Liner Review - 2011 Chevrolet Tahoe
Today on this 2011 Chevrolet Tahoe were going to do a test fit of part number WT42306 Weathertech. This is their floor liner for the cargo area. Today well be working with the grey color. This is also available as tan, as part number WT41306 and black as part number WT40306. This cargo liner is designed for vehicles that have three rows of seats with the second row as bucket seats. A couple of things to know about this cargo liner, that the shape, the channels and moldings are all designed to help keep dirt and debris contained in the liner and not in your carpet.
WeatherTech Front Floor Liners Review - 2011 Chevrolet Tahoe
Today in this 2011 Chevrolet Tahoe we are going to be test fitting the WeatherTech digital fit floor liners part number WT440661. Theses floor liners are black but they are also available in gray part number WT460661 as well tan part number WT450661. The first thing we need to remove is remove the OEM or preexisting floor mats from the vehicle. Once weve had those out of the way we are ready to drop in our WeatherTech liners. The WeatherTech liners are custom fit to the vehicles floorboard. Theyll fit the contours around the foot box and the transmission tunnel and theres even a place for the factory floor mat hook that the WeatherTech will use.
Husky Front Floor Liners Review - 2011 Chevrolet Tahoe
Today on this 2011, Chevrolet Tahoe we are going to test fitting the husky liner custom fit plastic floor mats part number HL31413. These are tanned but the liners are also available in gray part number HL31412 as well as black, part number HL31411. The first thing we need to do is remove the factory or preinstalled floor mats so that we can drop our husky liners in place. Its molded to fit around the contours of the foot box, the floor board even the transmission tunnel. On the underside are the stapled nibs that will help to hold the floor line in place. Theres lip around the floor liner that will make sure that all dirt and debris stays in the liner and off, of your carpet.
WeatherTech Cargo Floor Liner Review - 2011 Chevrolet Tahoe
Today on this 2011 Chevrolet Tahoe, were going to be test fitting the WeatherTech Cargo Liner, part number WT40307. This liner is black in color. However, its also available in tan, part number WT41307, as well as gray, part number WT42307. The WeatherTech liner is custom fit to your vehicle. Its designed to cover the entire cargo area and fit the contours of the interior. Theres a lip all the way around the cargo liner thats going to help keep debris on the mat.
Husky Rear Floor Liner Review - 2011 Chevrolet Tahoe
Today on our 2011 Chevrolet Tahoe, we're going to be test fitting the Husky Liners X-act Contour Floor Liner for the rear seat, part number HL53201. Before we can drop our Husky Liners X-act Contour set in, we need to remove the factory or previously installed floor mats. Once they're out of the way, we can set the Husky Liner X-act Contour piece into place. In this application, it's a single piece and it's molded to custom fit the vehicle. It's contoured along the center console, around the seat mounts for the front passenger and driver seats, and it has a lid all the way around to help hold dirt and debris on the liner. The channels and moldings in the surface of the X-act Contour Liner will help hold dirt and debris in the liner and keep it off of your carpet.
Husky Front Floor Liners Review - 2011 Chevrolet Tahoe
Today on this 2011 Chevrolet Tahoe, were going to be test fitting the Husky Liners X-act Contour Custom Floor Mats, part number HL53101. The X-act Contour Line is a heavy duty rubber liner that's custom molded to fit the vehicle. On the bottom of the liner is the Sta-Put Nibs that are going to help keep the liner in place in your vehicle. The liner is molded to fit the vehicle. They fit around the contours of the foot box, the floor board and the transmission tunnel. There are channels and moldings on the floor tunnel that are going to help keep dirt and debris trap on the liner and off of your carpet.
Trailer Brake Controller Installation - 2011 Chevrolet Tahoe
Today on this 2011 Chevrolet Tahoe, were going to be installing the Tekonsha P3 Brake Controller part number 90195. The first thing we need to do is find a suitable location for our mounting bracket. You'll want to make sure before you start mounting the bracket to the vehicle, that you check to make sure that there are no electrical components behind where you're going to mount it. Were clear on the back of this plastic tab and theres the metal structure here for our dash that we'll also be drilling in to. This is going to provide a secure mount for our brake controller. Next well use the small machine screws that came with our brake controller with the lock washers on them to mount the controller to the bracket.
Trailer Connector Socket Installation - 2001 Chevrolet Tahoe
Today on this 2001 Chevrolet Tahoe we are going to be installing part number HM40975 wiring kit from Hopkins towing solutions. The hardware that came with the kit is larger than normal, so we actually are going to be holding our bracket up in position so we can pre-mark our holes with a smaller drill bit so we can run our self tapping screws into our bumper. Then we will drill out our holes. :27
Trailer Hitch Installation - 2001 Chevrolet Tahoe
Today on this 2001 Chevrolet Tahoe we are going to be installing part number V81990 from Valley. The first thing we are going to do is show you our mounting locations. We are going to be taking out the bumper bolt on both sides of the vehicle. We are going to be using that bolt to install our hitch. The other one is going to be the forward most hole. It is going to be the same for the both the passenger and driver sides of the vehicle. We are going to be installing hardware into the stocked factory bumper itself. 00:28
Spiderweb Grille Installation - 2007 Chevrolet Tahoe
Today on this 2007 Chevrolet Tahoe we are going to install part number P303158 from Putco. This is their Putco liquid billet grille. In this particular unit we are going to install their spiderweb version. What this product does is it actually mounts on the top of the existing grille you have so you do not have to remove any parts at all. It is pretty easy to install you just have to loosen the grille up to get some working room but that is about it. The first thing we need to do is open the hood. The grille that is going to fit on top of this grille, the mounting point is right about this area so to get to that we are going to have to reach in from the top and over. It is really kind of hard to do with the space we have so that is why we are going to loosen up the grille. To do that we have got a series of bolts on the top to undo. It is really easy stuff. Basically we just need about one inch of room and we are good to go. 00:52
WeatherTech Cargo Liner Review - 2007 Chevrolet Tahoe
Today on this 2007 Chevrolet Tahoe we are going to install part number WT41306 from Weather Tech. This is their cargo liner. We are going to install this on the vehicle, the third row seating. If you notice about the Weather Tech floor liner, first off it is designed and engineered in the U.S.A. which is always good and these are custom molded to the vehicle itself using the companies exclusive rubberized resin and it actually covers the entire floor of your vehicle to keep dust and mud from getting in to the carpeting of the vehicle itself. 00:33
Chevrolet Tahoe Questions and Answers
- Do Westin Sure-Grip Running Boards 27-6130-1035 Come with Install Kit for a 2001 Chevy Tahoe
- You are correct. The Westin Sure-Grip running boards, # 27-6130-1035, does come with the installation kit that is a custom fit for your 2001 Chevy Tahoe. I have included a link to the installation instructions for you to view.
You will not need to add anything else for the installation but you may be interested in some accessories. You could use the gap strip # 27-9907 which covers up the little bit of space between the vehicle and the running board to provide a custom look. We also have lig
view full answer...
- Will the Hopkins Backup Sensor System, # HM60100VA, Fit a 2003 Chevy Tahoe
- The steel bumper on your 2003 Chevy Tahoe may make the sensors on the Hopkins Backup Sensor System, # HM60100VA, go off but if this happens all you will need to do is adjust the sensors so it does not give you a false alert. Some customers have also used spacers to mount the unit out a little further so the sensors will clear an obstruction.
view full answer...
- Suspension Enhancement for a 2003 Chevy Tahoe with Auto Level Rear Suspension
- I recommend installing a set of Timbren springs for added support. They will provide the support you need without having to run air lines and fill up or deflate air bags. Please keep in mind that adding Timbren springs or any suspension enhancement product may not stop the auto-leveling motor from running, but there is a very good chance that it will. If you have a 4-wheel drive model use # TGMRG25C. For a 2-Wheel drive model use # TGMRYS4.
Be sure to check your vehicle owners manual to make
view full answer...
- Weight Distribution Recommendation for a 2003 Chevy Tahoe and 4,500 Pound Travel Trailer
- When choosing weight distribution you want a system that has a tongue weight capacity that exceeds the total tongue weight of the trailer. You can figure the total tongue weight by taking the tongue weight of the trailer when loaded and ready to tow and then adding the weight of anything loaded behind the rear axle of the tow vehicle.
If 425 pounds is the dry tongue weight then it is likely to go higher when loaded. If it is close or above 600 then I recommend going up to the next higher syst
view full answer...
- Will Rhino-Rack Rooftop Cargo Carrier Bag # RRLBXL Fit On 2007 Chevrolet Tahoe
- The Rhino-Rack Rooftop Cargo Carrier Bag # RRLBXL is compatible with your 2007 Chevrolet Tahoe as long as you have side rails on your vehicle or are using this with a roof basket. With more than 21 cubic feet of space, you should have plenty of room for the travel gear for 3 adults and 2 children. If you look at the reviews for this product, one customer said they had ample space for 4 adults and 3 children.
This item also features weatherproof vinyl and lockable zippers to keep your belongin
view full answer...
- Will Flat Towing a Vehicle In Neutral Hurt the Transmission
- The best way to determine if a vehicle with an automatic transmission can be flat towed is to consult the owners manual under the towing section to see what restrictions they list for the vehicle. Some vehicles only require that the vehicle be put in neutral whereas some vehicles will require lube pumps or drive shaft disconnects.
If you want to email me back with the year and model of your VW I could do some research to see what is recommended for your vehicle to be flat towed.
I attached
view full answer...
- Custom Fit Towing Mirrors for a 2005 Chevy Tahoe with Electric Mirrors
- Yes, the Longview custom towing mirrors # CTM1500 are listed as a fit for a 2005 Chevy Tahoe with electric mirrors. I have included a link to a video showing a typical installation for you to view.
view full answer...
- 2-Bike Rack for Pedeco Interceptor Electric Bike And Beach Cruiser for 2007 Chevy Tahoe
- Due to the heavy weight of the E bike and the fact that a beach cruiser is not particularly lightweight, most of the 2 bike racks we offer will not have sufficient weight capacity.
Due to the weight involved, I would recommend a platform-type rack. These racks hold the bike by the wheels with a ratcheting hook that secures the top frame tube. These racks are usually easier to load, which is an important feature with heavier bikes.
My recommendation would be the Hollywood Racks Sport Rider
view full answer...
- Will Timbren System # TGMFK35C Fit 1995 Chevrolet Tahoe With Torsion Bar Front Suspension
- The Timbren Front Suspension Enhancement System, part # TGMFK35C, will fit your 1995 Chevrolet Tahoe 4WD with torsion bar front suspension. The Timbren rubber springs will install in place of your factory bump stop. You will want to make sure that the suspension on your vehicle is in good working order before installing the Timbren kit.
The Timbren kit is designed to work on vehicles with a snow plow. The rubber springs will raise the front of the end of the Tahoe when heavy equipment, such a
view full answer...
- Would the Draw-Tite Ball Mount # 40331 work in the Factory Hitch of a 2007 Chevy Tahoe
- As long as you have a hitch with a 2 inch opening the Forged Ball Mount # 40331 that you referenced will install in your hitch. This ball mount provides 4 inches of drop, which if you do not know to determine what rise/drop you need for your tow-vehicle/trailer setup I attached an FAQ article for you to check out.
You may also be interested in the following products to go along with the # 40331.
Pin and Clip # PC3
Hitch ball with 2-5/16 inch diameter # 19286
Hitch ball with 2 inch diamet
view full answer...
- Can Mirror Turn Signals be Added to a 2005 Chevy Tahoe WITHOUT Turn Signals in the Factory Mirrors
- If your 2005 Chevy Tahoe does not have turn signal functions in the mirrors then that function will not work on the K-Source Custom Extendable Towing Mirrors, # KS62075-76G. These mirrors have small connectors that plug into the vehicle factory connectors. The wiring in them carries the functions. It would be difficult to locate a place to tap into a turn signal function and then wire it into the connectors for the turn signals to function. If you could find a way to do it, yes, they would work.
view full answer...
- Front Mount Hitch Receiver Location on a 2007 Chevrolet Tahoe LT3 Z71
- I spoke with my contact at Curt and he told me that there is only one mounting option for the Curt Front Hitch, # C31012. This hitch was designed to mount to the underside of the frame rails, hanging below the frame as it is pictured (see photo). He also told me that this hitch was not designed or tested to mount in any other orientation and doing so could not only cause damage to the hitch and your vehicle, but would void the warranty of the hitch.
If you would like to determine where the r
view full answer...
- Is the Convert-A-Ball Ball Adapter Compatible with Other Weight Distribution Shanks
- The Convert-A-Ball Ball Mount Adapter, # BA-1, will work with any weight distribution shank that has 3/4 inch diameter holes that are 1-1/4 inches apart on center. I spoke with my contact at Convert-A-Ball and verified that you can use this adapter with any weight distribution shank that has the same bolt hole dimensions.
This adapter will work with your old Equal-i-zer shank. I actually pulled an Equal-i-zer weight distribution shank from my warehouse and made a video for you.
To attach
view full answer...
- Will Glacier Snow Chains # PW3029C Work on a 2012 Chevy Tahoe with 275/55R20 Tires
- The Glacier Cable Snow Tire Chains # PW3029C that you referenced are confirmed to fit 275/55R20 tires, so as long as you consult the owners manual of your 2012 Chevy Tahoe and it does not have any restrictions on snow chains listed then these should work well for you.
I attached an FAQ article on snow chains for you to check out also.
view full answer...
- Can Dual-Cam Sway Control be Added to a Draw-Tite Round Bar Weight Distribution System
- If your spring bars hang from chains and have the hook end like # RP58114 as an example, then you can add dual cam sway control, # RP26002. Drilling is required and there are no other dual-cam systems from the manufactures we carry that do not require drilling into the trailer frame for installation. I have linked a video and instructions for you. Since the system installs only on the trailer, switching between vehicles will not be a problem
If the dual cam system is not going to work for you
view full answer...
- Can the Rev Limiter be Adjusted Using a Bully Dog Triple Dog GT on a 2007 Chevy Tahoe with a 5.3L
- I spoke with my contact at Bully Dog about the Triple Dog GT tuner, # BY40410GMC. On your 2007 Chevy Tahoe with the 5.3 liter engine you can adjust the rev limiter. My contact stated that on 2004 to 2012 models the rev limiter can be adjusted but not on earlier models.
To adjust the Rev Limiter you have to do it during the initial installation. When you first install the tuner it asks you several questions about adjusting tire size, speed limiter, and other items. It is in this initial set up
view full answer...
- Can WeatherTech Rear Cargo Mat for a 2013 Chevy Tahoe be Trimmed to Fit Around 3rd Row of Seats
- Cargo mat # WT42306 that you purchased for your 2013 Chevy Tahoe can be trimmed to allow the seats to fit in place over it. It was designed for this purpose so it is permissible and at your discretion if you want to do so. If you look at the pictures of the mat you will see the areas that can be cut out to account for the third row of seats.
view full answer...
- Data Parameters for Bully Dog WatchDog Monitor # BY40402 on 2003 Chevrolet Tahoe
- After speaking to my contact at Bully Dog, I have found that the Bully Dog WatchDog Monitor # BY40402 you referenced for your 2003 Chevrolet Tahoe does display the transmission temperature as well as the temp of your engine coolant. It runs diagnostic checks and clears trouble codes and comes with a 1-year warranty. I have included a link to the instructions for the installation of this product.
view full answer...
- Ability of Bully Dog Watch Dog Gauge Monitor to Correct Speedometer for Larger Tires
- Because the Bully Dog Watch Dog is a monitor only, it is not capable of programming or changing anything on the vehicle, including the speedometer calibration.
However, the Watch Dog does have a speedometer display function that can be calibrated for accuracy, see page # 23 of the owners manual, which I have linked you to. While driving, you would just ignore the speedometer reading on the vehicle and go by the corrected speedometer reading shown on the Watch Dog.
view full answer...
- Availability of a 3-Step Electric Step for Travel Trailers
- You have a valid concern about operation of this product with a partially depleted trailer battery. I researched similar products and I did not find any specifically intended for travel trailer use.
One solution is to procure a separate 12V automotive battery for operating the steps, provided that your trailer has a suitable place to locate one without requiring excessively long wire runs or the risk of causing pinched or shorted wiring. In this scenario a battery charger might also be a good
view full answer...
- Will CA-Emissions-Equipped 2003 Chevrolet Tahoe Ron More Slowly Than Other Tahoes
- I cannot state conclusively whether or not your Tahoe, which originated in California, will have less acceleration capability than a similar vehicle. This will depend on more factors than the just the type of catalytic converters employed, such as the condition of the engine tune, other aftermarket equipment, engine mileage, fuel grade used, etc. Top speed is usually governed by the vehicle computer and may be the same for those originating in CA and those from elsewhere.
Generally speaking (
view full answer...
- What is the Clearance from the Roof to Bottom of Bars on the Thule Crossroads Roof Rack
- On the Thule Crossroads roof rack, # TH45058, from the top of the side rails on the vehicle to the bottom of the crossbars once the system is installed measures approximately 1-1/2 inches. This is the measurement at the side rails. Most vehicle roofs are higher in the middle of the vehicle so there will be a little less clearance there.
Measure from your roof to the top of the side rails and then up another 1-1/2 inches to get a good approximation of where the bottoms of the bars will be once
view full answer...
- Information Needed to Pick out a Base Plate Kit to Flat Tow a 2000 Chevy Tahoe
- In order to pick out the correct base plates for a 2000 Chevy Tahoe you are going to need to know the following information. You will need to know if the tow hooks on your vehicle attach externally or internally of your frame, the payload of your vehicle (1/2 ton or 3/4 ton) and whether or not you have 4 wheel or 2 wheel drive.
Once you know that information check out the link I provided that will allow you to select which model you have and the correct base plate kits will be left for you t
view full answer...
- Weight Distribution for 2007 Chevy Tahoe LTZ Towing 2012 Titan Primo 2-horse Trailer
- If your old system was not properly adjusted or was overloaded, it would explain why not enough weight was transferred to the front vehicle axle. Generally speaking, tilting the weight distribution head back toward the trailer will distribute more weight to the front axle of the tow vehicle, as will using fewer links in a chain-hanger type system. Your old system might indeed still be usable, if its capabilities are compatible with the weight of your trailer. Consult the set-up instructions for
view full answer...
- Which Surco Safari 5.0 Roof Rack for 2004 Chevy Tahoe
- The correct Surco roof basket for your Tahoe will depend on how your roof is currently equipped.
If you have the raised side rails that run from the front to the rear of the roof, the # SPS5084-1101, which does not require crossbars would be ideal.
If your Tahoe is a Z71 model with the roof that has the flush-mounted tracks that run from front to back, the # SPS5084-Y400 rack you mentioned would be the correct choice once the Yakima crossbars, # Y00408 and # Y00138 are installed.
view full answer...
- Weight Distribution for a 2005 Chevy Tahoe and Dutchmen Aerolite 195QB Travel Trailer
- When choosing a weight distribution system you will need to go by the tongue weight of the trailer when loaded and ready to tow plus the weight of anything loaded behind the rear axle of the tow vehicle.I did some research and found that on a 2012 Dutchmen Aerolite 195QB the gross trailer weight is approximately 5,400 pounds. Tongue weight is typically 10 to 15 percent of gross trailer weight so we are looking at 540 to 810 pounds.
If nothing is loaded behind the rear axle on the Tahoe then y
view full answer...
- Trailer Brake Controller Does Not Power On on a 2007 Chevy Tahoe
- If this is a new installation then the probable cause is that you will need to make some connections under the hood on your 2007 Chevy Tahoe. I have included a link to an FAQ article that will help you with this. If you have the connections in place then check the fuse locations in the spots closest to where the two wires attach as indicated in the FAQ.
If this is a problem that suddenly occurred but was working before then it could be the fuse that powers the brake controller. If so, replac
view full answer...
- Floor Mats For Second Row Seats and Third Row Seats Including Cargo Area on 2008 Chevrolet Tahoe
- If you have three rows of seats in your 2008 Chevrolet Tahoe the floor mats I have available for the second row that will also cover the carpet in the middle are the Husky Liners Floor Mats, part # HL61422. I am including a link to a video of these floor mats being installed on a 2007 GMC Yukon, which is a similar vehicle.
For the third row and the cargo area I would recommend the Husky Liners Cargo Liner, part # HL21412. This mat will install under the third row seats and extend back to the
view full answer...
- Weight Distribution Shank with 7-1/2 Inches of Drop for a 2008 Chevy Tahoe
- If you are measuring on level ground to the top of the receiver opening on the vehicle and to the bottom of the coupler on the trailer then the difference is 7-1/2 inches and that is the amount of drop you will need to tow the trailer level. Shank # RP3344 will provide this amount of drop if you are using a weight distribution system. I have included a link to an FAQ on measuring for the correct rise or drop.
For a regular ball mount the closest we have to 7-1/2 inches is # 45291. Or, to go w
view full answer...
- Parts Needed to Make a Tekonsha Primus Brake Controller Fully Functional on a 1997 Chevy Tahoe
- The first thing you are going to need is a 4-way trailer connection at the rear of your 1997 Chevrolet Tahoe if you do not have one. For that you will need a Tow Ready T-One Vehicle Wiring Harness # 118319. I attached installation instructions and video for this product for you to check out.
Next, you will need to convert the 4-way to a 7-way so that the Tekonsha PRIMUS IQ Electronic Brake Controller # TK90160 that you referenced can function. For that you will need a Brake Controller 7 and 4
view full answer...
all Chevrolet Tahoe questions
