Select Your Vehicle
view cartView Cart
Only 21 Hours 56 Minutes Remaining

Buick Enclave owners are most interested in these products

change vehicle



Buick Enclave Videos



Trailer Wiring Harness Installation - 2013 Buick Enclave

Today on our 2013 Buick Conclave, we'll be installing the Tow Ready, T1 Vehicle Wiring Harness, part number 118579. To begin our installation on the vehicle wiring harness, we'll need to raise the rear hatch of the vehicle. We'll need to remove each of the taillight assemblies. To do this, we'll need to remove two covers that cover up small bolts on each side. You'll see that there's a bolt under each cover. We'll need to remove each of these bolts. Once these two have been removed, we can gently slide the whole light assembly out towards the rear of the vehicle.



Trailer Hitch Installation - 2013 Buick Enclave - Hidden Hitch

Today, on our 2013 Buick Enclave, well be installing the Hidden Hitch trailer hitch receiver in a Class III with a two-inch opening on the receiver, part number 87435. Heres what the hitch looks like installed on our vehicle. Now, well go ahead and give you a couple measurements in helping you choose some accessories for your hitch such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pinhole to the outermost edge of the bumper is approximately 4 inches. From the top of the opening in the receiver to the ground is approximately 18 inches. Now, lets go ahead and install our hitch. To begin with, were going to install a safety strap up underneath the exhaust. Well hook each side to the safety strap and with the rear sprints on the vehicle.



Trailer Hitch Installation - 2013 Buick Enclave - Curt

Today on our 2013 Buick Enclave, we'll be installing the Curt Trailer Hitch Receiver in a Class 3, with a 2-inch receiver opening. Part number 13424. Here's what the hitch looks like installed on our vehicle. Now I'll go ahead and give you a couple of measurements in helping you choose some accessoriesfor your hitch, such as a ballmount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outermost edges of the bumper is, approximately4 1/2 inches. From the top of the opening of the receiver to the ground isapproximately18 inches.Now, let's go ahead and install our hitch. We'll begin by removing the center plastic section on our rear lower bumper fascia. Todo this, there are two tabs, one on each side, that we'll need to turn. Then simply pull down on the center section, and it will release from the bumper cover. Now, we can go ahead and see the mounting locations of where we're putting our hitch job with.



Thule Vertex 4 Hitch Bike Rack Review - 2013 Buick Enclave

Today on our 2013 Buick Enclave, well be test fitting the Thule Vertex 4-Bike Rack for 1-1/4 and 2 inch hitches, part number TH9029. To begin our test fit, well slide the shank of the bike rack into the receiver tube of the hitch. Line up the pin hole and thread in our anti-rattle bolt, tightening it with a wrench. Now well go over a few clearance of measurements. We have about 17 inches of ground clearance. The closest point of the bike rack to the rear of our vehicle is about 2 inches.



Thule Hitching Post Pro Hitch Bike Rack Review - 2013 Buick Enclave

Today on our 2013 Buick Enclave, well be test fitting the Thule hitching post pro, folding and tilting four-bike rack with anti-sway, fitting the inch-and-a-quarter and two-inch hitches, part number th934xtr. To begin our test fit, well slide the shank of the bike rack into the receiver tube of in the hitch. Well line up the pin hole, and thread in our anti-rattle bolt tightening it with a wrench.Now, well go over a few clearance measurements. We have about 15 and three quarter inches of ground clearance. The closest point of the bike rack to the rear of our vehicle is about six inches. Weve added about 16 inches to the overall length of our enclave.



Thule Apex 4 Swing Hitch Bike Rack Review - 2013 Buick Enclave

Today on our 2013 Buick Enclave, well be test fitting the Thule Apex, Swing four-bike rack for two-inch hitches, part number TH9027. To begin our test fit, well slide the shank of the bike rack into the receiver tube of the hitch. Allow the attached pin to fall into place, and secure it by tightening the hand knob, which will engage out anti-rattle device. Now, well over a few clearance measurements. We have about 16 and a quarter inches of ground clearance. The closest for another bike rack to the rear of our enclave is about half-an-inch, and weve added about 13 inches to the overall length of our vehicle.Well pull the lever at the top of the mast to swing out our dual arms.



Thule Apex 4 Hitch Bike Rack Review - 2013 Buick Enclave

Today on our 2013 Buick Enclave, we'll be test fitting the Thule Apex FourBike Rack, 4-inch and a quarter and 2 inch hitches, part number th9025. We'll begin our test fit by slotting the shank of the bike rack into the receiver tube of the hitch. We'll line up the pin hole and allow the attached end to fall into place. We'll then tighten the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now we'll go over a few clearance measurements. We have about 17 inches of ground clearance. The closest from the bike rack to the rear of the vehicle is about 3/4 of an inch.



Yakima HighLite 2 Hitch Bike Rack Review - 2013 Buick Enclave

Today on our 2013 Buick Enclave, well be test fitting the Yakima Highlite Aluminum 2-Bike Rack for 1-1/4 and 2 inch hitches, part number Y02438. To begin our test fit, well slide the shank of the bike rack into the receiver tube of the hitch. Line up the pin hole and install the attach pin. Well then move to the rear of the shank and tighten the hand knob to secure our bike rack to our vehicle and engage our anti-rattle device. Now well go over a few clearance of measurements. We have about 16 inches of ground clearance.



Trailer Wiring Harness Installation - 2013 Buick Enclave

Today on this 2013 Buick Enclave, we're going to install part number 119147KIT from Tow Ready. First thing we need to do is go ahead and open up the back hatch and get access to the tail lights. Then, we need to remove two plastic covers for the screws. You can pry them just a little bit and they simply pop off. Once we have access to the screws, we'll go ahead and unbolt the tail light. With the screws removed we'll go ahead and gently pull the tail light out backwards and away from the body work.



Husky Liners Classic Custom 3rd Row Rear Floor Liner Review - 2013 Buick Enclave

Today, on a 2013 Buick Enclave, we're going to install part number HL71021 from Husky Liners. This is Husky Liner's classic custom auto floor liner for a third row in black. To start off, I'm going to go ahead and remove the existing floor mat in the floor. We want to get down to bare carpet. Then we can go ahead and lay the new Husky Liner into place. Just fold it up as needed to work it in between the seats, then lay it down. After it's in place, we can see it has ridge all the way around the edges.



U-Ace 3D Kagu Front Floor Liners Review - 2013 Buick Enclave

Today, on our 2013 Buick Enclave, we'll be doing a test fit of the U Ace 3D Kagu Custom Auto Floor Liners with MAXpider Grips for the front in black color, part number L1BC00811509. These floor liners are also available in beige, part number L1BC00811502. Additionally, they are also available in a gray color, part number L1BC00811501. Before we can install our new 3D KaguCustom Auto Floor Liners we need to remove the any existing or factory mats that may already be in place. We'll start here, on the driver's side. You simply turn the locking tab that holds the factory mat in place, lift off, and set aside.



Thule Apex 4 Swing Hitch Bike Rack Review - 2011 Buick Enclave

Today on our 2011 Buick Enclave, we'll be test fitting the Thule Apex Swing 4-bike carrier, part number TH9027. We'll begin our test fit by sliding the shank of the carrier into the opening of the hitch, allowing the integrated hitch pin to fall into the pin holes, and then we'll turn the black knob to engage our anti-rattle device. Now with our Thule Apex secured to our Enclave, we'll go over a few clearance measurements to see how the two fit together. We have about 17-1/2" of ground clearance at the rear of the bike rack. The closest part of the bike rack to the closest part of our Enclave is at the rear bumper, about 1" away, and we've added about 11" of overall length to our Enclave with the Thule Apex secured. We can now pull the gray lever at the top of the mast to swing the cradle arms out, and with the cradle arms out we've added about 35" to the overall length of our Enclave.



Yakima DoubleDown Ace Hitch Bike Rack Review - 2011 Buick Enclave

Today on our 2011 Buick Enclave, we'll be test fitting the Yakima DoubleDown Ace 4 Bike Carrier, part number Y02451. We'll begin our test fit by sliding the shank of the bike rack into the opening of the hitch, lining up the pin holes, inserting the pin with the red knob into the pin holes, and inserting the black knob at the back of the shank to engage the anti-rattle device. Now with our DoubleDown Ace secured to our Enclave, we'll go over a few clearance measurements to see how the two fit together. We have about 20-1/2 inches of ground clearance to the rear of the bike rack. Closest part of the bike rack to the closest part of our Enclave is here at the rear bumper about 4-1/2 inches away. With the cradle arms folded down, we've added about 9-1/2 inches to the overall length of our vehicle.



Yakima DoubleDown Ace 2 Bike Rack Review - 2011 Buick Enclave

Today on our 2011 Buick Enclave, we'll be test fitting the Yakima DoubleDown Ace 2 Bike Carrier, part number Y02450. We'll begin our test fit by sliding the shank of the bike rack into the opening of the hitch, lining up the pin holes, inserting the pin with the red knob into the pin holes, and inserting the black knob at the back of the shank to engage the anti-rattle device. Now with our DoubleDown Ace secured to our Enclave, we'll go over a few clearance measurements to see how the two fit together. We have about 20 inches of ground clearance to the rear of the bike rack. Closest part of the bike rack to the closest part of our Enclave is here at the rear bumper about 4 inches away. With the cradle arms folded down, we've added about 9-1/2 inches to the overall length of our vehicle.



Thule Apex 4 Hitch Bike Rack Review - 2011 Buick Enclave

Today on our 2011 Buick Enclave, we'll be test fitting the Thule Apex 4 Bike Carrier, part number TH9025. We'll begin our test fit by sliding the shank of the bike rack into the opening of the hitch, allowing the integrated hitch pin to fall into place, and then we'll turn the black knob at the base of the bike rack to engage the anti-rattle device. Now that our Thule Apex is secured to our Enclave, we'll go over a few clearance measurements to see how the two fit together. We have about 19 inches of ground clearance at the rear of the bike rack. Closest part of our Apex to the closest part of our Enclave is here at the rear bumper about an inch, and we've added about 11-1/2 inches to the overall length of our Enclave. We'll now pull the gray lever at the top of the mast to swing the cradle arms out.







Thule Vertex 4 Hitch Bike Rack Review - 2010 Buick Enclave

Today on our 2010 Buick Enclave well be test fitting the Thule vertex four bike carrier, part number TH9029. To begin out test fit well slide the shank of the carrier into the opening of the hitch tube, line up our pin hole, thread our anti-rattle bolt through the threaded pin hole and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and the vehicle fit together. There is about 16 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 1 inches. Weve added about 11 inches to the overall length of the vehicle.



Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2010 Buick Enclave

Today on our 2010 Buick Enclave well be test fitting the Swagman XTC two bike carrier, part number S64670. To begin our test fit well slide the shank of the carrier into the opening of the hitch tube, line up our threaded pin holes, thread our anti-rattle bolt through the threaded pin holes and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 1/2 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 4 inch. Weve added about 20 1/2 inches to the overall length of the vehicle.



Swagman Titan Hitch Bike Rack Review - 2010 Buick Enclave

Today on our 2010 Buick Enclave well be test fitting the Swagman titan four bike carrier, part number S63410. To begin our test fit well slide the shank of the carrier into the opening of the hitch, line up our threaded pin holes, thread our anti-rattle bolt through the threaded pin holes and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 7 inch. Weve added about 20 inches to the overall length of the vehicle.



SportRack EZ Hitch Bike Rack Review - 2010 Buick Enclave

Today on our 2010 Buick Enclave well be test fitting the Sportrack two bike carrier, part number A30901. To begin out test fit well slide the shank of the carrier into the opening of the hitch tube, align up our threaded pin holes, thread our anti-rattle bolt through the threaded pin holes and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 8 inch. Weve added about 25 inches to the overall length of the vehicle.



SportRack Escape 3 Hitch Bike Rack Review - 2010 Buick Enclave

Today on our 2010 Buick Enclave well be test fitting the Sportrack escape three bike carrier, part number A30403. To begin our test fit well slide the shank of the carrier into the opening of the hitch, line up our hitch pin hole and thread our anti-rattle bolt through the threaded pin holes and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 16 1/2 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 6 inch. Weve added about 11 inches to the overall length of the vehicle.



Pro Series Q-Slot Hitch Bike Rack Review - 2010 Buick Enclave

Today on our 2010 Buick Enclave well be test fitting the Pro Series Q-slot platform style two bike carrier, part number PS63134. To begin out test fit well slide the shank of the carrier into the opening of the hitch tube, line up our hitch pin holes, slide the pin through our pin hole and secure it with a clip. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 7 inch. Weve added about 25 inches to the overall length of the vehicle.



Pro Series Eclipse 4 Hitch Bike Rack Review - 2010 Buick Enclave

Today on our 2010 Buick Enclave well be test fitting the Pro Series eclipse four bike carrier, part number 63124. To begin out test fit well slide the shank of the carrier into the opening of the hitch tube, line up our threaded pin holes, thread our anti-rattle bolt through the threaded pin holes and tighten with a wrench. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 16 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 3 inch. Weve added about 29 inches to the overall length of the vehicle.



Kuat Sherpa Hitch Bike Rack Review - 2010 Buick Enclave

Today on our 2010 Buick Enclave well be test fitting the Kuat Sherpa aluminum two bike carrier, part number S102. To begin our test fit well slide the shank of the carrier into the opening of the hitch then turn the black handle located at the base of the carrier to engage our anti-rattle device. Now lets go over some clearance measurements to see how the bike carrier and this vehicle fit together. Theres about 17 inches of ground clearance. The closest part of the carrier to the closest part of the vehicle is about inch. Weve added about 12 inches to the overall length of the vehicle.



Husky Rear Floor Liner Review - 2010 Buick Enclave

Today on our 2010 Buick Enclave well be test fitting the Husky floor liner in the second row, part number HL61021, black in color. Before we test fit the Husky floor liner well remove the old or manufactured floor mat. Husky floor liners are custom molded precisely fit the vehicle and stay in place. The shape, channels and moldings all work to keep dirt and debris contained in the liner and off the carpeting. As you can see this is a one piece liner. It extends all the way from the driver to the passenger side threshold.



Husky Front Floor Liners Review - 2010 Buick Enclave

Today on our 2010 Buick Enclave well be installing the Husky Floor Liner in the front row part number HL31011 black in color. First well go ahead and remove the old or manufacturer floor mats and now were ready to install the Husky Liner Floor Liner. The Husky Floor Liners are custom molded to precisely fit the vehicle and stay in place. The shape, channels and moldings all work to keep dirt and debris contained in the liner and off of the carpeting. As you can see here its custom molded to fit over the manufacturers attachment point, it has a raised outer edges and is custom molded to fit the manufacturers floor board and around the threshold here on the drivers side. Additionally, its custom molded to fit around the drivers side foot rest and has an extended front edge up underneath the dashboard for full coverage up underneath the gas and brake pedal.



Rain-X Latitude Wiper Blades Installation - 2010 Buick Enclave

Today on our 2010 Buick Enclave, we'll be installing the Rain-X Latitude Wiper Blades using part number RX5079278 as well as RX5079280. To begin the installation, we'll need to remove the factory or old windshield wipers from the vehicle. To do this, we'll push the button here on the arm which will allow us to slide the blade out and remove it from the arm. With that done, we'll open up our packaging for our new Rain-X Latitude Wiper Blades and we'll notice right off the bat that we do have to change the attachment point here. Now included with the Latitude is the correct attachment point. To remove the old one, we'll simply push the lever here which will allow us to slide the attachment point off of the blade.



Trailer Hitch Installation - 2010 Buick Enclave - Curt

Today on our 2010 Buick Enclave well be installing the Curt hitch, part number 13424. This is what our hitch will look like once its installed. Next well go ahead and give you a couple measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is five and a quarter inches. From the top of the receiver tube to the ground is 18 inches. This will assist you with selecting accessories such as a draw bar, a bike rack or cargo carrier.Now well go ahead with installation.



Westin Running Board Installation - 2009 Buick Enclave

Today on our 2009 Buick Enclave well be installing the Westin Sure Grip Running Boards part number 27-6620-1835. Our first step will be identifying our brackets. The brackets will be used to bolt to the underbody of the vehicle and then to the running board. This will be our front bracket. Well also go ahead and show you the front bracket hardware. The front bracket again will bolt to the underbody of the vehicle and then to our running board.



Husky Cargo Floor Liner Review - 2009 Buick Enclave

Today, on our 2009 Buick Enclave, well be installing the Husky Liner Classic Custom Cargo Liner in black, part number HL21061. This liner also comes in grey, part number HL21062. In tan, part number HL21063. Now to begin the installation well need to remove the factory or old cargo mat from the vehicle, if equipped. We can now simply place our Husky Liner Cargo Liner into our cargo area, allowing it to conform to the floor of the Enclave. Youll notice this custom molded floor liner fits into your Buick Enclave trunk or cargo area perfectly.



WeatherTech Front Floor Liners Review - 2009 Buick Enclave

Today on our 2009 Buick Enclave, we'll be test-fitting part number WT442511. Thisis the WeatherTech Front Auto FloorLiners, in black. These liners are also available ingrey, part number WT462511, and tan, part number WT452511. To begin our install, we'll simply remove the factory or old floor mats from thevehicle, if equipped. With the old floor mats removed, we're now ready to install ournew WeatherTech FloorLiners. The WeatherTech FloorLiners are custom molded,to ensure a perfect fit for each Buick Enclave.



WeatherTech Rear Floor Liner Review - 2009 Buick Enclave

Today on our 2009 Buick Enclave, we'll be installing the WeatherTech 2nd and3rd Row Rear Auto FloorLiner, part number WT441114, in black. This liner is alsoavailable in grey, part number WT461114, and tan, part number WT451114. To begin the installation, we'll need to remove the factory or old floor mats fromthe vehicle. We can then simply fit our floor liner, allowing it to conform to the floorof our Enclave. You'll notice this liner is a one-piece liner, covering both the secondand third row of your Enclave. Between the two bucket seats, it has a cut-out for therear center console.



Trailer Hitch Installation - 2012 Buick Enclave - Hidden Hitch

Today on this 2012 Buick Enclave, well be test fitting part number 87435 from Hidden Hitch. Here are a few measurements to assist you when ordering your accessories. From the center of the hitch pin hole to the outer most point of the bumper is 3-1/4 inches. From the top of the receiver tube to the ground is 18-3/4 inches. This will help you when selecting accessories. To begin our install well need to remove the cover here at the rear bumper.



Trailer Hitch Installation - 2012 Buick Enclave - Curt

Today on our 2012 Buick Enclave, we'll be installing part number 13424 from Curt. Here are a couple of measurements to help you when selecting accessories. From the top of the receiver tube to the ground is 18-3/4 and from the center of the hitch pinhole to the outermost point of the bumper is 4-1/4. Now well go ahead with our install. To begin our install, well need to remove the cover here at the rear bumper. To do that well just undo the clasps on either side.



WeatherTech Rear Floor Liner Review - 2012 Buick Enclave

Today on this 2012 Buick Enclave were going to be test fitting the WeatherTech Floor Liners for the 2nd and 3rd row, part number WT461114. This liner is a single piece that covers all the floor for both the 2nd and the 3rd row. Well start by removing the preexisting floor mats from our Enclave. With our existing floor mats out of the way we can now drop in the Husky Liner. The liners are custom molded to fit our vehicle. Theyll fit around all the seat tracks, the air conditioning vents, and even over our factory mounting points for the existing floor mats.



WeatherTech Cargo Floor Liner Review - 2012 Buick Enclave

Today on this 2012 Buick Enclave were going to be test fitting the WeatherTech Liner for the Cargo Area, part number WT40424. This liner is designed to cover up not only the cargo area but the 3rd row seats as well. It will cover all the way from the 2nd row seats back. Its custom molded to fit the contours of our Enclave and protect the carpet. It has a tray edge around the perimeter that will help contain dirt and debris and keep it off your carpet. When the liner gets dirty it can simply be removed and washed with soap and water.



Husky Third Row Floor Liner Review - 2012 Buick Enclave

Today on this 2012 Buick Enclave were going to be test fitting the Husky Liners for the 3rd row, part number 71021. Well start by removing the preexisting floor mats and detaching them from their posts. Once weve got the preexisting floor mats out of the way, we can drop in our Husky Liners. The liner is custom molded to our vehicle. There are cut outs for all air conditioning vents, it fits around our seat tracks, and therere even places for the liner to go over our factory floor mat hook posts. The shape and tray edge of our Husky Liner helps to direct dirt and debris toward the center of liner and keep it off of your carpet.



Husky Rear Floor Liner Review - 2012 Buick Enclave

Today on this 2003 Buick Enclave were going to be test fitting the Husky Liners for the 2nd row, part number HL61021. Well start by removing the factory floor mat from the second row of the vehicle. Once the existing floor mats are out of the way we can drop our Husky Liner into place. The Husky Liners are custom shaped to fit the contour of the vehicle. Theyll move around the console, the seat tracks and theyll even fit over the existing retention hooks through the factory floor mat. The shape and tray lip on our Husky Liners help keep dirt and debris and moisture trapped in the liner and off of your carpet.



Husky Front Floor Liners Review - 2012 Buick Enclave

Today on this 2012 Buick Enclave were going to be test fitting the Husky Floor Liners for the front, part number HL31011. First well remove the existing floor mats. With them out of the way we can drop in our Husky Liner Floor Liners. The liners are custom molded to fit the vehicle. Theyll fit over the foot rest underneath the pedals, or on the air conditioning vent and over the factory attachment point. The surrounding edge on the liner helps keep all the dirt and debris and water trapped within the liner and off of your vehicles carpet.



Husky Cargo Floor Liner Review - 2012 Buick Enclave

Today on this 2012 Buick Enclave were going to be test fitting the Husky Liner for the cargo area part #: hl21061. This line is designed to fit in the area behind the 3rd row seats. With the cargo area of Enclave cleared we can go ahead and drop in the Husky liner. The liner is designed to fit the contours of the vehicle and form a tray shape that will help keep dirt and debris on the liner and off of your carpet. When the liner gets dirty it can quickly and easily be removed from the vehicle, washed with soap and water and once dried and returned it will continue protecting the carpet. That does it for our test fit of the Husky liner for the rear cargo area in black, part #: hl21061.



Yakima SwingDaddy 4 Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick Enclave we will be test fitting the Yakima Swingdaddy4 bike bike rack part no. Y02422. We will begin our test fit by inserting the bike rack shank into the hitch. We will line up the hitch pin hole and insert and tighten down our anti-retal bolt. We will then give you a few measurements. We have 20 inches of ground clearance with this bike rack and it is 3 inches from the closest point of the bike rack to the back of the vehicle.



Yakima Holdup Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick Enclave we will be test fitting part no. Y02433, the Yakima Holdup2 hitch mounted wheel mount cradles for 2 inch hitches. We will being by inserting the bike rack shank into the hitch. We will line up our hitch pin hole and insert our anti-retal bolt. We will then tighten it down with a wrench. After putting our safety pin in the other side of the anti-retal bolt our bike rack is secured to the vehicle and we can load up our bike.



Yakima DoubleDown 5 Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick Enclave we will be test fitting the Yakima Doubledown 5 bike hitch mounted bike rack part no. Y02425. To begin our test fit, we will insert the bike rack into the hitch line up the hitch pin hole and insert our anti-retal bolt. We can then tighten it down with a wrench. We will now go ahead and give you a few measurement. the ground clearance with this bike rack is 16 and 3/4 inches and from the closest point of the bike rack to the back of the vehicle is 6 inches.



UWS Aluminum Cargo Carrier Review - 2012 Buick Enclave

Today on our 2012 Buick Enclave, we will be test fitting the 23 X 51 alluminium cargo carrier by UWS part no. UWS03511. To begin our test fit we will simply slide the cargo carrier shank into the hitch, lign up the hitch pin hole and insert the hitch pin. We can then put the safety pin on the other side of the hitch which will secure it to the vehile. We will go ahead and give you a few measurement at this point from the closes point of the cargo carrier to the back of the vehicle is more an inch. The inside openning measures 20 and 3/8 inches wide by 48 and 1/2 inches long, by 5 and 5/8 high.



Pro Series Eclipse 4 Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick Enclave we will be test fitting the Tow Ready 4 bike hitch mounted bike rack for 2 inch hitches part no. 63124. To begin our test fit we will insert the bike rack shank into the hitch, line up the hitch pin hole, insert and tighten down our anti-retal bolt. We will then put our safety pin on the other side of the anti-retal bolt which will secure our bike rack to the vehicle and we can go ahead and give you some measurements. Our bike rack has 16 inches of ground clearance and it is 4 inches from the closest point of the bike rack to the back of the vehicle. We will now go ahead and unfold the bike rack to open our cargo door.



Thule Vertex 4 Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 buick enclave we'll be test fitting the Thule vertex 4 bike carrier part no. TH9029. A quick note about this carrer, it will fit both inch and 1/4 and 2 inch hitches class 1 through class 3 although when using with a class 1 hitch you are limited to 2 bikes. Our vehilce is equipped with the 2 inch hitch so we're ready to go ahead and fit it to the vehicle. We will simply slide the bike rack shank into the hitch. We will line up the hitch pin hole and insert our anti-retal bolt.



Thule T2 Platform Style Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick Enclave, we'll be test fitting the Thule T2 platfrom style bike carrier part no. TH916 XTR. We will begin our test fit by installing the bike rack shank into the hitch, we will line up the hitch pin hole and install our anti-retal bolt. We can then put our locking mechanism on the other side of our anti-retal bolt which will secure our bike rack to the vehicle. We can then give you a few measurement. With the bike rack in a stored position, there is one inch of clearance between the closest point of the bike rack and the bumper, you have 17 inches of ground clearance with the bike rack and it will add an additional 30 inches to the overall lenght of our vehicle.



Thule Parkway 2 Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick Enclave we will be test fitting the Thule Parkway 2 bike carrier part no. TH958. We'll simply install the bike rack shank into the hitch, we'll line up the hitch pin hole and insert our anti-retal bolt where we can then tighten it down with the ranch. With the bolt tight, our bike rack is secured to the vehicle and we'll go ahead and give you a few measurements. Our ground clearance with this bike rack is 17 inches and from the closest point of the bike rack to the bumper is about half an inch. We'll now go ahead and attempt to gain cargo access, we'll remove the pin and lain here and fold the bike rack down, we can then open the cargo door and as you can see we can gain full cargo access with this bike rack.



Thule Helium Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick Enclave we will be test fitting the Thule helium alluminium 2 bike carrier part no TH 970 XT. A quick note on this bike rack it can work with both an inch and 1/4 and 2 inch hitches with the included adapter. Our vehicle is equiped with the 2 inch hitch and with our adapter installed we're ready to go ahead and fit it to the vehicle. We will begin by inserting the bike rack shank into the hitch, we'll line up the hitch pin hole and insert the included key. We can then move to the anti-retal knob where we will tighten it down to secure it to the vehicle. We will now go ahead and give you some measurements.



Thule Doubletrack Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick Enclave we will be test fitting the Thule double track platform style bike carrier part no. TH990XT. This bike carrier can be used with both inch and 1/4 and 2 inch hitches class 1 through class 3. To begin our test fit we will insert the bike rack shank into the hitch line up the hitch pin hole and install our anti-retal bolt and that will secure our bike rack to the vehicle we can give you a few measurements. There are 16 and 1/2 inches of ground clearance with this bike rack and it is 3 and 1/2 inches from the closest point of the bike rack to the back of the vehicle in the stored position. There is 27 inches of overall length added to the vehicle with the platform down.



Thule Apex 4 Hitch Bike Rack Review - 2012 Buick Enclave

Today or our 2012 Buick Enclave, we'll be test fitting part no TH9025 the Thule Apex 4 bike carrier. A quick note on this bike rack, it will fit both inch and 1/4 or with the included adaptor a 2 inch hitch class 1 through class 3. However if using it in a class 1 hitch you are limited to 2 bikes. We begin our test fit by installing the bike rack shank into the hitch. We will pull our intergrated locking hitch pin and as we slide the shank into the hitch the pin will slide in place. We can then tighten down the anti-retal knob to secure it to the vehicle.



Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick Enclave we will be test fitting the Swagman XTC2 2 bike carrier part no S64670. Now our bike rack is already assembled and ready for a 2 inch hitch although by removing the including spacer blocks it may also be used in an inch and 1/4 hitch. We can start by inserting the bike rack shank into the hitch. We will line up the hitch pin hole and insert our anti retal bolt. We can then tighten it down with a wrench and that will secure our bike rack to the vehicle and we can go ahead and give you a few measurements. From the closest point of the bike rack to the bumper is 4 and 1/2 inches and our ground clearance is 20 and 1/2 inches.



Swagman Titan Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick enclave we'll test fitting part no. S63410 the Swagman Titan4 bike carrier for both inch and 1/4 and 2 inch hitches. With our vehicle equiped with the 2 inch hitch we've preassembled our bike rack using the included spacer block and we're ready to fit it to the vehicle. We will simply slide the bike rack shank into the hitch, line up the hitch pin hole and insert our anti-retal bolt and tighten it down with the wrench. We will then put the safety pin on the other side of the anti-retal bolt which will secure our bike rack to the vehicle and then we will go ahead and give you some measurements. Our ground clearance with this bike rack is 19 inches and from the closest point of the bike rack to the back of the vehicle is 7 inches.



SportRack EZ Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick Enclave, we will be test fitting part number A30901. The SportRack 2 bike hitch mounted bike rack for both 1-1/4 and 2 inch hitches. Now our vehicle is equipped with the 2 inch hitch so we're ready to go ahead and fit it to the vehicle using the included spacer block. We will simply insert the bike rack shank into the hitch. We will line up the hitch pin hole and insert our anti-rattle bolt.



SportRack Evader Hitch Bike Rack Review - 2012 Buick Enclave

Todayd on our 2012 Buikc Enclave we will be test fitting the sportrack Evader 3 bike carrier part no. A30403XT. Quick not on this bike rack, it will fit both inch and 1/4 and 2 inch hitches using the included space block. Our vehicle is equiped with the 2 inch hitch so with our spacer block installed we're ready to go ahead and fit it to the vehicle We will begin by sliding the bike rack shank into the hitch, we will line the hitch pin hole and install our anti retal bolt. We can then tighten it down with a wrench. With our anti retal bolt tight, we will install the safety pin on the other side, this will secure the bike rack to the vehicle.



Rhode Gear Highway Hitch Bike Rack Review - 2012 Buick Enclave

Today on our 2012 Buick enclave, we will be test fitting the Rhodegear highway 2 bike carrier part no. RG8015220. A quick note on this bike rack it will work on both inch and a quarter and 2 inch hitches class 1 through class 3. To begin our test fit we will simply install the bike rack shank into the hitch, line up the hitch pin hole and insert the anti retal bolt. We can then tighten it down with a wrench which will secure our bike rack to the vehicle and we can go ahead and give you some measurements. Our ground clearance with this bike rack is 16 inches and from the closest point of the bike rack to the back of the vehicle is 6 inches.



Curt Hitch Cargo Carrier Review - 2012 Buick Enclave

Today on our 2012 Buick enclave, we'll be test fitting the curt 20 X 48 cargo carrier part no. C18145. A quick note about this cargo carrier, it will work in both inch and 1/4 and 2 inch hitches using the included space We will slide the cargo carrier shink into the hitch we'll lign up the hitch pin hole and insert our anti retal bolt. We can then tighten it down with a wrench. Once it's tight, our cargo carrier is secured to the vehicle and we can go ahead and load it up. We'll go ahead and give you a few measurements on our cargo carrier, the insert dimentions of our cargo carrier arre 46 and 3/8 inches long by 17 and 1/2 inches wide by 5 and 1/2 inches tall.



Rhino Rack Roof Rack with Aero Crossbars Installation - 2008 Buick Enclave

Today on this 2008 Buick Enclave, we're going to be test fitting a Rhino Rack 2500 Series Roof Rack System. We'll be using the fit kit, part number DK224, and the crossbar kit, part number DA1375B. We already have our crossbar assemblies put together. Now, we're ready to fit them upon the vehicle. The first thing we need to do is open both the front doors. Next, we can set our front crossbar assembly up on top of the roof of our vehicle.



Base Plate Wiring Harness Installation - 2009 Buick Enclave

Today on this 2009 Buick Enclave we are going to install 38955. We will start off by taking the wire harness and just pull it on through so the 4-pole harness is going to end up by the tow bar and wrap up some of the wire with some electrical tape to keep it nice and together. Leave some extra hanging out for now. Now lets continue on routing our wire from the front of the vehicle all the way back and we are going to make sure we stay away from anything that is moving or hot. What we will do is take our ground wire and we are going to attach it to this cross member right here. Now we will continue on running the harness to the back of the vehicle. 00:38



Roadmaster Base Plate Installation- 2009 Buick Enclave

Today on this 2009 Buick Enclave we will be installing part number 523149-1 from Roadmaster. The first thing we need to do is get underneath the hood of the vehicle and remove some fasteners so we can remove the front fascia. There are 12 fasteners that need to be removed. To remove the rivet there is a dent inside here that you pop the screwdriver in and kind of pick up the middle part. Then you can use your rivet tool and just pull it out. These sunken rivets are a pain, just take your screwdriver and work your way around it. Then remove the engine cover. Now there is a Phillips screw, one on each side that we need to remove. :56



Trailer Wiring Harness Installation- 2010 Buick Enclave

Today on this 2010 Buick Enclave we are going to be installing wiring harness part number 118450. We are at the rear cargo area of the Enclave, and we are going to locate the ports that we are going to be plugging our wiring harness into. These ports are actually located directly behind the tail light assembly on both the driver and passenger side. So, the first thing we want to do is remove both tail light assemblies. To do that we are going to open up the rear cargo door, there are two inboard screws holding the tail light into place. We need to pull back the covers to expose those. :30



Trailer Hitch Installation - 2010 Buick Enclave

Today on this 2010 Buick Enclave we are going to be installing Draw-Tite hitch part number 75528. This installation will also apply to Hidden Hitch part number 87435. We are looking at the underside of the vehicle. On this Enclave you can see we have this fascia door covering. We want to remove that. There are two screws here on the bottom holding it in. Then we can just set it off to the side. :26



Trailer Brake Controller Installation - 2010 Buick Enclave

Today on this 2010 Buick Enclave we are going to be installing Prodigy brake controller along with the wiring kit part number 90185-3026P. We are inside the vehicle and we are right below the steering column. You need to locate the port that we will be plugging our brake controller harness into. This port is located back behind this black covering over by the emergency brake pedal. We need to remove this black covering first. There are three retaining clips holding it into position. One here nearest the emergency brake pedal, one in the middle, and then one over on the far right side. 00:42



Trailer Wiring Harness Installation - 2009 Buick Enclave

Today on this 2009 Buick Enclave we will be installing wiring harness part number 118450. The connection points for our wiring harness are located directly behind the tail light assemblies on both of the drivers and passengers sides. So the first thing we need to do is go ahead and remove both of those. And that will expose the two screws that are holding the tail light onto the vehicle. We will go ahead and remove those. We will just gently pull away the tail light connector that we are going to be connecting our harness into located right here. We want to go ahead and press the tab here at the top of the connector. And that will allow us to pull the two pieces apart. I am going to set the tail light aside for the time being. We will take the harness here and we will start with the connectors that have the yellow and brown wires on it.



Trailer Hitch Installation - 2009 Buick Enclave

Today on this 2009 Buick Enclave, we will be installing Draw-Tite hitch part number 75528. This hitch installation will also apply to Hidden Hitch part number 87435. Okay before we get started with our hitch installation we need to do a couple things in preparation. First we have already lowered the spare tire to get it out of the way. On the Enclave here we have got this rear fascia door that our hitch opening is actually going to come out through so we want to go ahead and remove this by simply turning the thumb screws here at the bottom of the door and pulling it away. We are going to go ahead and also need to lower our dual exhaust down. There are four hangers that we are going to need to lower the exhaust off of in order for us to have enough room to get the hitch into place. We have got two in here on the inboard side.





Buick Enclave Questions and Answers


all Buick Enclave questions      



Subscribe to email newsletter

Email  

privacy - we don't send unsolicited email



Only 21 Hours 56 Minutes Remaining

etrailer.com reviewsetrailer.com reviews

All images, layout and content copyright etrailer.com