Top 20 Most Popular Toyota Sequoia Cargo Carrierschange vehicle

UWS Aluminum Cargo Carrier Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia we'll be test fitting the 23 by 51 Aluminum cargo carrier for two-inch hitches, part number UWS03511. Now to begin our test fit we'll simply slide the cargo carrier shank into the hitch, line up the hitch pinhole and install our hitch pin and that will secure our carrier to the vehicle. Now we'll go ahead and give you a few measurements. From the closest point of the cargo carrier to the bumper of the vehicle is 4-1/2 inches and this cargo carrier will add an additional 27-1/4 inches to the overall vehicle length. Now the exhaust exits the passenger rear on this vehicle and is approximately six inches from the cargo carrier platform. It also appears to be about two inches lower than the platform so there will be little to no heat transfer while you are driving down the road and that completes our test fit of the 23 by 51 Aluminum cargo carrier for two-inch hitches, part number UWS03511 on our 2012 Toyota Sequoia..

Curt Hitch Cargo Carrier Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia well be test fitting the Curt 20x48 cargo carrier for both 1 and 2 inch hitches part #: C18145. Now to begin our test fit well simply slide the cargo carrier shank into the hitch using the included adapter for the 2 inch hitch. With it in place well go ahead and install our anti-rattle bolt tightening it down. With the bolt tight our cargo carrier is secured to the vehicle. Now well go ahead and give you a few measurements. The closest point of the cargo carrier is 4 inches from the bumper and the cargo carrier will add an additional 2 feet to the overall length of your vehicle.

Surco Folding Hitch Cargo Carrier Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia, we'll be test fitting part number 52018F, the Surco 24x60 folding cargo carrier for two-inch hitches. To begin our test-fit, we'll simply slide the cargo carrier shank into the hitch, line up the hitch pin hole, and install our hitch pin. And that will secure our cargo carrier to the vehicle. Now, we'll go ahead and give you a few measurements. Our ground clearance with this cargo carrier is 17 inches, and from the closest point of the cargo carrier in the stored position to the back of the vehicle is four inches. We can now pull the pin on the cargo carrier to bring the platform down.

Curt 20x60 Folding Aluminum Cargo Carrier Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia, we'll be test-fitting the Curt 20x60 Folding Aluminum Cargo Carrier, part number C18100. Now to begin our test-fit, we'll simply slide the cargo carrier shank into the hitch, line up the hitch pin hole, and install our hitch pin. Now that our cargo carrier is secured to the vehicle, we'll go ahead and give you a few measurements. From the closest point of the cargo carrier to the back of the vehicle is two and a half inches, and our ground clearance of this cargo carrier is 18 inches. Now, we'll go ahead and pull the pin on the cargo carrier to fold the carrier down. And we'll give you a few more measurements.

Yakima RocketBox Pro 11 Rooftop Cargo Box Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia, were going to be test fitting the Yakima RocketBox Pro 11 Rooftop Cargo Box, part number Y07193. With our vehicle already equipped with a full roof rack system and our box already preassembled, we can go ahead and set the RocketBox on top of the load bars. Once we have it in position on top of the load bars, well go ahead and open the lid and use the hand knobs to tighten down the clamps. This will secure the RocketBox to the load bars of our roof rack system. Now, we can go ahead and close our lid and were ready to hit the road. And that does it for the test fit of the Yakima RocketBox Pro 11 Rooftop Cargo Box, part number Y07193, on our 2012 Toyota Sequoia..

Yakima LoadWarrior Roof Cargo Basket Review - 2012 Toyota Sequoia

Today on this 2012 Toyota Sequoia, well be test fitting the Yakima LoadWarrior Roof Rack Cargo Basket, part number Y07070. With our basket already preassembled and our vehicle equipped with the manufacturers roof rack system, we can go ahead and set the basket directly into position on top of the roof rack. After we get the cargo basket on top of the rack and centered, well go ahead and use the clamps to secure the basket on the roof rack. At this time, well just run our fasteners down finger tight to secure the carrier on top of the rack. Now, well go ahead and make sure our basket is centered on the load bars and then well go back and tighten two of the fasteners to secure the basket to the roof rack. And there you have it.

Thule MOAB Roof Top Cargo Basket Review - 2012 Toyota Sequoia

Today on our 2012 Toyota Sequoia we'll be test fitting the Thule MOAB Roof Top Cargo Carrier, part number TH690. With our vehicle equipped with the manufacturer's roof rack system and our cargo basket already pre-assembled we are ready to go ahead and install it on the top of the load bars of the vehicle. First, we'll install our fasteners to secure the clumps around the load bars. Once we install them, we'll just run them down finger tight. Next, we'll go ahead and center the cargo basket on the roofline of the vehicle. Now with our cargo basket centered up, we are ready to go ahead, and tighten and secure all of our fasteners.