Top 20 Most Popular Toyota RAV4 Ball Mountschange vehicle

Toyota RAV4 ball mounts Videos

Toyota RAV4 Ball Mounts Questions

• Ball Mount and Ball Needed To Tow Utility Trailer with 2011 Toyota RAV4
  
• In order to determine which ball mount you need you will need to take some measurements. Measure the distance from the top of your receiver opening down to the ground. Then with the utility trailer sitting on the jack so that it is perfectly level, measure the distance from the bottom of the coupler to the ground. The difference between these measurements is the amount of rise or drop you will need. If the receiver height is taller than the trailer coupler height, you will need a ball mount with
  view full answer...


• Ball Mount Dimensions for a Class I Hitch on a 2003 Toyota Rav 4
  
• The distance from the center of the hitch pin hole on the Draw-Tite Sportframe Ball Mount, item # 3593, to the back of the shank is 1-1/2 inches, so it will fit fine in your Class I hitch. I have added the dimension to the photo at the right, click on the photo to enlarge it for better viewing. You may also need a hitch ball to complete your towing setup. If your trailer coupler takes a 1-7/8 inch ball you can use the # 19256 ball or if your coupler takes a 2 inch ball you can use the # 19258
  view full answer...


• Ball Mount Recommendation for Pulling a Pop Up Camper with a 2011 Toyota Rav4 with Rear Spare Tire
  
• The standard ball mount that is recommended for the 2011 RAV4 has a 2 inch drop and a 3/4 inch rise and in most cases the # 80232 ball mount will be correct, but this does not mean that it will be the correct ball mount height for towing your trailer. The height of your trailer coupler and the height of the top of the receiver opening on your RAV4, when parked on a fairly level surface with the trailer frame level, will be needed to determine the correct ball mount drop or rise that you will
  view full answer...


• Long and Short Ball Mount Options for a 2012 Toyota RAV4 Towing a Boat and Boat Trailer
  
• From the center of the hitch pin hole to the center of the ball hole on ball mount # 2923 it measures 8-1/2 inches. This should put the ball about flush with the back of the spare tire on a 2012 Toyota RAV4 based on installations we have done. Measure your specific vehicle to be certain. Boat trailers generally have a coupler at the end of a long pole tongue. And the shape of most boats combined with the pole tongue would allow you to easily make turns without any interference issues. Ho
  view full answer...


• Super Extra Long Ball Mount Recommendation for a 2012 Toyota RAV4
  
• I believe the correct ball mount for you to use would be the Hidden Hitch Ball Mount # 80233. This ball mount has a distance of 10 inches from the center of the hitch pin hole out to the nearest part of the weld-on ball mount platform, and since the hitch on your 2012 Toyota RAV4 has a distance of 9.5 inches from the center of the hitch pin hole to the furthest point of the bumper I believe this ball mount would work well for you. This ball mount also has a rise of 2-3/4 inches, and if you ge
  view full answer...


• What is the Correct Ball Mount for a 2003 Toyota RAV4 with a Class I Draw-Tite Trailer Hitch
  
• On a Class I trailer hitch, you must use the ball mount recommended by the trailer hitch manufacturer or it will void the hitch warranty. this is because that specific hitch has been tested with and rated for use with a specific ball mount and has been determined to be the best option. This information can be found near the bottom of the hitch instructions, linked for reference. They state that ball mount # 3593 is correct for this hitch and vehicle. The instructions all state that it must be
  view full answer...


• What Size Bike Rack on Draw-Tite Hitch 75432 for 2008 Toyota RAV4
  
• You can use any hitch-mounted bike rack with a 2-inch hitch opening with Draw-Tite hitch 75432, however, if you have a door-mounted spare tire, make sure that you have clearance for a bike rack. I have included a link below to the 2-inch hitch-mounted bike rack that will fit with this hitch.
  view full answer...


• Where is the Rise Measured from on a Curt Euro Ball Mount
  
• The 3-1/8 inches of rise that the Curt Class II Euro Style Drawbar # C45562 has is measured from the top of the shank to the beginning of the vertical bend below the ball. Check out the video I attached to see this measurement.
  view full answer...