Top 20 Most Popular Hyundai Santa Fe Bike Rackschange vehicle

Yakima HighLite 2 Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Yakima Highlite aluminum two bike carrier, part number Y02438. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up our pin holes, insert the attached pin into the pin hole and turn the black knob to engage our anti-rattle bolt. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 11 1/2 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier at the bottom of the bumper is about 4 inches. With the cradle arms folded down we've added about 10 inches to the overall length of the vehicle measured at the bumper.

Yakima DoubleDown Ace Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Yakima Doubledown Ace four bike carrier, part number Y02451. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up our pin holes, insert the attached pin into the pin hole and turn the black knob to engage our anti-rattle bolt. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 11 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier at the bottom of the bumper is about 5 inches. With the cradle arms folded down we've added about 12 inches to the overall length of the vehicle measured at the bumper.

Thule Vertex 4 Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Thule Vertex four bike carrier, part number TH9029. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up the pin holes, thread our anti-rattle bolt through the pin holes and tighten with a wrench. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 12 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier is about 3 inch at the bottom of the bumper. With the cradle arms folded down we've added about 12 inches to the overall length of the vehicle measured at the bumper.

Thule Apex 4 Swing Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Thule Apex swing, four bike carrier, part number TH9027. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up our pin holes, insert the spring loaded pin through the pin hole and tighten down the knob to engage our anti-rattle device. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 12 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier at the anti-rattle knob is about 1 inch. With the cradle arms folded down we've added about 10 inches to the overall length of the vehicle measured at the bumper.

Thule Apex 4 Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Thule Apex four bike carrier, part number TH9025. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up the pin holes, insert the spring loaded pin into the pin hole and turn the black knob to engage our anti-rattle device. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 12 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier at the anti-rattle knob is about 1 inch. With the cradle arms folded down we've added about 13 inches to the overall length of the vehicle measured at the bumper.

Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Swagman XTC 2 two bike carrier, part number S64670. Now to begin our test fit we'll slide the shank of the carrier into the opening of the hitch, line up the pin holes, thread our anti-rattle bolt through the pin holes and tighten with a wrench. Now we'll go over some clearance measurements to see how the bike carrier and this vehicle will fit together. There is about 12 inches of ground clearance. Closest part of the carrier to the closest part of the vehicle here at the rear bumper is about 8 inches. We've added about 24 inches to the overall length of the vehicle measured from the rear bumper.

SportRack Escape 3 Hitch Bike Rack Review - 2012 Hyundai Santa Fe

Today on our 2012 Hyundai Santa Fe we'll be test fitting the Sportrack Escape three bike carrier, part number A30403. Now to begin our test fit we'll slide the bike rack shank into the opening of the hitch, line up our pin holes, thread our anti-rattle bolt through the pin holes and tighten it with a wrench. Now we'll go over some clearance measurements to see how the carrier and this vehicle will fit together. There is about 12 inches of ground clearance. Closest part of the vehicle to the closest part of the carrier is about 5 inch. With the cradle arms folded down we've added about 12 inches to the overall length of the vehicle measured at the bumper.

Thule Parkway 2 Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with the 2009 Hyundai Santa Fe, and were going to be test fitting the Thule Parkway Two hitch mounted bike carrier, part number TH958. To mount the carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up the hitch pin hole, thread in our anti-rattle bolt and tighten it down with a wrench. Next we want to check for rear vehicle access. Well remove the pin at the base of the bike rack and tilt it down. We want to make sure that we can still open the cargo door completely and access the cargo area of our Santa Fe, even with the bike rack installed.

Thule Doubletrack Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with a 2009 Hyundai Santa Fe, and were going to be test fitting the Thule Doubletrack hitch mounted bike carrier, part number TH990XT. To mount the carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch, making sure we line up the hitch pin holes. Then well thread in our anti-rattle bolt and tighten it down using a wrench. Next well go over a few clearance measurements. Weve got about 10 inches of ground clearance from the bottom of the bike rack to the ground. Weve got about two inches of clearance from the closest part of the vehicle to the closest part of the bike rack.

Pro Series Eclipse 4 Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today on our 2009 Hyundai Santa Fe were going to be test fitting the Pro Series Eclipse Four hitch mounted bike carrier, part number 63124. To mount our carrier to the vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well then thread in our anti-rattle bolt and tighten it down using a wrench. Next we want to check for rear vehicle access. Well remove the pin at the base of the bike rack and tilt it down. We just want to make sure that we can fully open our cargo door and access the area, even with the bike rack installed.

Yakima StickUp 2 Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with a 2009 Hyundai Santa Fe, and were going to be test fitting a Yakima Stickup Two hitch mounted bike carrier, part number Y02420. To mount this carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up our hitch pin hole and thread in our anti-rattle bolt, tightening it down with a wrench. Next well go some clearance measurements. Weve got about 11 inches of ground clearance from the bottom of the bike rack to the ground. Weve got about a half inch of clearance between the closest part of the bike rack and the carrier.

Thule Vertex 4 Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with the 2009 Hyundai Santa Fe, and were going to be test fitting the Thule Vertex Four hitch mounted bike carrier, part number TH9029. To mount our carrier to our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well line up the hitch pin hole, thread in our anti-rattle bolt and then tighten it down with a wrench. Next we want to check for rear vehicle access. Well grab the switch at the base of the bike rack and tilt it down. We want to make sure that we can open the cargo door completely and still access the area, even with the bike rack installed.

Thule Hitching Post Pro Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with the 2009 Hyundai Santa Fe, and were going to be test fitting the Thule Hitching Post hitch mounted bike carrier, part number TH934XTR. To mount this bike rack to our vehicle well insert the shank of the carrier into the receiver tube of the hitch. Well feed on our anti-rattle bolt and tighten it down with a wrench. Next we want to check for rear vehicle access. Well remove the pin at the base of the bike rack and tilt it down. We want to make sure that we can open our cargo door completely and access our cargo area.

Thule Apex 4 Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today were working with the 2009 Hyundai Santa Fe, and were going to be test fitting the Thule Apex Four hitch mounted bike carrier. To mount our carrier to the vehicle well make sure that we pull over the automatic hitch pin, slide the shank into the receiver tube and let the hitch pin secure on its own. Then well tighten down the bike using the hand knob at the base to activate the anti-rattle device. Next we want to check for rear vehicle access. Well grab the switch at the base of the bike rack and tilt it down. We want to make sure that we can open the cargo door all the way and access our cargo area, even with the rack installed.

Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today on our 2009 Hyundai Santa Fe, we're going to be test fitting the Swagman XTC 2 Hitch Mounted Bike Carrier, Part Number S64670. To mount the carrier to our vehicle, we'll insert the shank in the carrier into the receiver tube of the hitch. We'll make sure to line up the hitch pin hole and thread in our anti-rattle bolt. We'll then tighten it down using a wrench. With the bike rack secure, we want to check some clearance measurements. We've got about 11-1/2 inches of ground clearance from the bottom of our bike rack to the ground.

SportRack EZ Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today, we're working with the 2009 Hyundai Santa Fe and we're going to be test fitting the SportRack 2 Hitch Mounted Bike Carrier, Part Number A30901.To mount the carrier to the vehicle, we'll insert the shank of the carrier in the receiver tube with the hitch. We'll make sure to line up the hitch pinholes then insert our anti-rattle bolt, and tighten it with a wrench. Next, we'll go over a few clearance measurements. We've got about 11-1/2 inches of ground clearance from the bottom of the bike rack to the ground. We have about 6 inches of clearance between the closest part of the bike rack and the closest part of the vehicle. Overall, we've added about 23 inches of additional length to the rear of the vehicle.

Pro Series Q-Slot Hitch Bike Rack Review - 2009 Hyundai Santa Fe

Today on our 2009 Hyundai Santa Fe, we're going to be test fitting the Pro Series Q Slot Hitch Mounted Bike Carrier, Part Number PS63134. To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of our hitch. We'll make sure to line up the hitch pinhole and then we'll secure the rack with the pin and clip. Next, we'll go over some clearance measurements. We've got about 11-1/2 inches of ground clearance from the bottom of the bike rack to the ground. We've got about 5-1/2 inches of clearance between the closest part of our bike rack and the closest part of our vehicle.

Pro Series Q-Slot Hitch Bike Rack Review - 2008 Hyundai Santa Fe

Thule Hitching Post Pro Hitch Bike Rack Review - 2008 Hyundai Santa Fe

Rhode Gear Highway Hitch Bike Rack Review - 2008 Hyundai Santa Fe

Yakima ForkLift Roof Mounted Bike Rack Review - 2007 Hyundai Santa Fe

Today on our 2007 Hyundai Santa Fe, we're going to be test fitting the Yakima ForkLift Roof Mounted Bike Carrier, part number Y02098. Our Santa Fe already has a factory roof rack system on it, so well be installing the forklift directly to the factory crossbars. Well take the bike rack and place it up on top of our crossbars. We'll fit the front clamp around the front crossbar and use the wing nut and T-bolt to tighten it down. Then we'll slide our cover back into place and we'll move to the rear. We'll fit the rear clamp around the rear bar and again we'll use the T-bolt and wing nut to tighten that down.

Yakima FrontLoader Roof Bike Rack Review - 2007 Hyundai Santa Fe

Today on our 2007 Hyundai Santa Fe, we're going to be test fitting the Yakima FrontLoader Roof Mounted Bike Rack, part number Y02103. Our Santa Fe is equipped with a factory roof rack so we're going to mount our FrontLoader directly to that. To mount the FrontLoader, we'll lift it up and place it on top of our crossbars. We'll take the head of the bike and fit the front clamp around our front bar and we'll use the hand nut to tighten it down. In the rear, we'll fit the rear clamp around the bar and use the T-bolt and wing nut to tighten it down. Once we've done that, our bike rack is secured and we're ready to load up a bike.

RockyMounts TieRod Roof Bike Rack Review - 2007 Hyundai Santa Fe

Today we have with us a 2007 Hyundai Santa Fe and were going to be test fitting the Rockymounts Tierod Roof Mounted Bike carrier part number RKY1014. Our vehicle already has a full factory roof rack so were ready to go ahead and mount our bike rack to the bars. To fit our bike rack, well place it on top of our bars and put the head of the rack on our front bar making sure its wrapped the rubber-coated steel strap on the bar. Well fit them back into the head and tighten them down with the Allen key. Once weve done that, we can reinstall the cover of the head of the bike rack. At the back of the bike rack, well take our rear clamp, fit it around the bar and use the included wing nut to tighten it down.

RockyMounts TieRod Roof Bike Rack Review - 2010 Hyundai Santa Fe

Today on our 2010 Hyundai Santa Fe, well be test fitting the RockyMounts Tie Rod roof-mounted bike carrier part number RKY1014. To begin our test fit, well place the bike rack on top of our factor cross bar, well move to the rear mounting point where well undo the wing nut and bring the clamp underneath the crossbar where well use the wing nut to secure the rear clamp. Well move up to the front crossbar where well use the rubber-coated steel straps to go underneath the crossbar and hook back to the head of the bike rack. We can then use the Allen wrench included with the bike rack to tighten down the Allen bolt securing our rubber-coated steel straps to the front crossbar. With that done, we can reinstall the head cover on our bike rack and now were ready to load up our bike. Well take the front wheel off of our bike and place the bike on top of the bike rack.