Top 20 Most Popular Chevrolet Equinox Bike Rackschange vehicle

Yakima StickUp 2 Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox we'll be test fitting the Yakima StickUp 2 Bike Hitch Mounted Folding Bike Rack for both one and a quarter and two inch hitches, part number y02420. Now to begin our test fit, we'll simply slide the bike rack shank into the hitch. Line up the hitch pin hole and install and tighten our anti-rattle bolt and with the bolt tight, our rack is secured to our vehicle. We'll now go ahead and go over a few clearance measurements. We have a ground clearance of 12 1/2 inches and from the closest point of the bike rack to the closest point on the rear of our vehicle is three inches. With the bike rack in the folded position, we've added 12 inches to the overall length of our vehicle.

Yakima HighLite 2 Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox we'll be test fitting the Yakima Highlite Aluminum 2 Bike Carrier, part number y02438. To being our test fit, we'll slide the shank of the carrier into the opening of our hitch. Line up the hitch pin holes and insert our pin with the red knob into the pin hole and then turn the black knob at the bottom of the carrier to engage our anti-rattle device. Now we'll go ahead and go over a few clearance measurements. We have about 12 inches of ground clearance and from the closest part of the carrier to the closest part of our vehicle is about four inches. With the bike carrier in the folded position, we've added ten inches to the overall length of our vehicle.

Yakima DoubleDown Ace Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox we'll be test fitting the Yakima Doubledown Ace 4 Bike Carrier for inch and a quarter and two inch hitches, part number y02451. To begin we can go ahead and slide the bike rack shank into our hitch. Line up the hitch pin hole and install the attached hitch pin. We can then go ahead and tighten the knob down here at the back of the shank, securing the bike rack to the vehicle. At this point we can go over a few clearance measurements. Our ground clearance here at the bike rack measures 11 1/2 inches and the closest part of the bike carrier to the rear of our vehicle is five inches.

Thule T2 Platform Style Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox we're going to be test fitting the Thule T2 Platform-Style Bike Carrier, part number th916xtr. To mount the carrier to the vehicle, we'll enter the shank of the carrier into our receiver tube. We'll line up the hitch pin holes and then thread in our anti-rattle bolt and tie that down with a wrench. Once we're done that, we'll go over some clearance measurements. We have a ground clearance of 12 inches and the closest point of the bike rack to the closest point of the vehicle is about three inches. With the bike rack in the folded position, we've added 12 inches to the overall length of our vehicle.

Thule Doubletrack Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox we're going to be test fitting the Thule Doubletrack Hitch Bike Rack, part number th990xt. We'll begin by taking the shank of the bike rack and sliding it into the receiver tube of our hitch. We'll then thread an anti-rattle bolt and tighten it down using the wrench. With our bike rack secured to our vehicle, we'll now go ahead and go over a few clearance measurements. We have 11 1/2 inches of ground clearance and the closest part of the bike carrier to the closest part of the vehicle is three and a half inches. With the bike rack in the folded position, we've added about ten inches to the overall length of our vehicle.

Thule Apex 4 Swing Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox, we'll be test fitting the Thule Apex Swing Four-Bike Carrier, Part Number TH9027. To begin our test fit, we'll slide our bike rack shank into the hitch and allow the integrated lock and hitch pin to fall into place. We'll then move to the anti-rattle knob where we'll tighten down the knob, securing our bike rack to the vehicle. Now, we'll go over a few clearance measurements. We have a ground clearance of 12 inches and the closest part of the bike carrier to the closest part of the rear of our vehicle is about 3 inches. With the bike rack in its folded position, we've added 12 inches to the overall length of our vehicle.

Thule Apex 4 Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox, we'll be test fitting the Thule Apex Four-Bike Carrier, Part Number TH9025. Now to begin the test fit, we'll slide the bike rack shank into the hitch and that'll allow our integrated locking hitch pin to fall into place. We can then move to the anti-rattle knob and tighten it down, which will secure our bike rack to our vehicle. We'll now go ahead and go over a few clearance measurements. We have a ground clearance of 13 inches and from the closest point of the bike rack of the rear of our vehicle is about 3 inches. With the bike rack in the folded position, we've added an overall length of 12 inches to our vehicle.

Swagman Titan Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012, Chevrolet Equinox, we'll be test fitting the Swagman Titan Four-Bike Carrier for both 1-1/4 and 2-inch Hitches, Part Number S63410. To install our carrier, we'll slide our bike rack shank into the hitch, line up the hitch pinhole, and install or tighten down our anti-rattle bolt. With our bolt tight, our bike rack is secured to our vehicle. And now, we'll go over a few clearance measurements. We have a ground clearance of 13 inches and from the closest point of the bike rack to the closest point of the vehicle is about 7 inches. With the bike rack in the folded position, we've added 19 inches to the overall length of our vehicle.

Softride Dura Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012, Chevrolet Equinox, we'll be test fitting the Softride Dura Hitch Bike Rack, Part Number SR26247. We're going to begin by simply sliding the bike rack shank into the hitch. We'll line up the hitch pinhole and install our anti-rattle bolt. With our bolt tight, our bike rack is now secured to the vehicle. Now, we can go ahead and go over a few clearance measurements. We have a ground clearance of 12 inches.

Rhino-Rack 4 Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox, we're going to be test fitting the Rhino Rack Four-Bike Carrier for 2-inch Hitches, Part Number RBC038. To mount our carrier to the vehicle, first, we'll insert the shank of the carrier into the receiver tube of our hitch and then we'll thread in our anti-rattle bolt, and tighten it down using a wrench. Now, we can go over a few clearance measurements. We have a ground clearance of 12-1/2 inches. The closest part of our carrier to the closest part of our vehicle is about two inches. With the bike rack in the folded position, we've added nine inches of additional length to the rear of our vehicle.

Prorack 2 Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today, on out 2012 Chevrolet Equinox, we'll be test-fitting the Pro Rack, two-bike carrier for one-and-a-quarter and two-inch hitches, part number PR8062403.Now, to begin our test-fit, we'll slide the shank of the carrier in to the receiver tube of our hitch, line up the hitch pinhole. Then we'll throw in our anti-rattle bolt, tighten it with a wrench, and secure it with a pin on the other side. Now, well go over a few clearance measurements. We have a ground clearance of 11 1/2 inches. The closest part of the carrier to the closest part of our vehicle is about two inches. We've added about 23 inches of additional length to the rear of our vehicle.

Kuat Beta Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today, on our 2012 Chevrolet Equinox, we'll be test-fitting the Kuat Beta Aluminum Folding two-bike hitch-mounted bike carrier, for two-inch hitches, part number B202-2.To begin our test-fit, we'll slide the shank into the hitch. We'll line up the pinholes, and install the included hitch pin. Now, we can go ahead and move to the back of the shank, and tighten the knob, securing our bike rack, and engaging the anti-rattle device.At this point, we'll go over a few clearance measurements. We have a ground clearance of 12 inches, and from the closest point of the bike rack to the closest point of the rear of the vehicle is three inches. With the bike rack in its folded position, weve added about 10-and-a-half inches to the overall length of our vehicle.We'll now go ahead and pull the pin at the base of the mast, and tilt the mast down. As you can see, we can easily gain access to our cargo area.

Hollywood Racks Traveler 5 Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today, on our 2012 Chevrolet Equinox, we'll be test-fitting the Hollywood Racks Traveler five-bike carrier, part number HR9200. To begin our test fit, we'll slide the shank of the carrier into the opening of the hitch, line up our pinholes, and then throw in our anti-rattle bolt through the pinholes, and tighten with a wrench.Now, well go ahead and go over a few measurements. We have about 12 inches of ground clearance, and the closest part of the carrier to the closest part of the vehicle is about five inches. With the cradle arms folded, we've added 15 inches to the overall length of our vehicle. To access the cargo area, we'll pull the pin at the bottom of the mast, and tilt down our carrier.To load the bike, we'll make sure that the mast is in its upright position. We'll undo the cradle straps, set the bike into the frame cradles, and secure it with the straps.That complete todays test fit for the Hollywood racks Traveler five-bike carrier, part number HR9200, on our 2012 Chevrolet Equinox..

Hollywood Racks Traveler Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today, on our 2012 Chevrolet Equinox, we'll be test-fitting the Hollywood Racks Traveler four-bike carrier, part number HR8500. To begin our test fit, we'll slide the shank of the carrier into the opening of the hitch, line up our pinholes and the thread our anti-rattle bolt through the pinholes and tighten them with a wrench.Now, with the carrier secured to the vehicle, we'll go over a few clearance measurements. We have a ground clearance of 12 inches. The closest point of the bike carrier to the closest point of the rear of our vehicle is about an inch. With the bike rack in its folded position, weve added nine inches to the overall length of our vehicle.We'll pull the pin at the bottom of the mast to activate out tilt feature. As you can see, we can easily gain access to the cargo area of our vehicle.

Hollywood Racks Sport Rider SE2 Bike Rack Review - 2012 Chevrolet Equinox

Today, on our 2012 Chevrolet Equinox, we'll be test fitting the Hollywood Racks Sport Rider, SC2, two-bike carrier for two-inch hitches, part number HR1450. To begin our test fit, we'll slide the bike rack shank into the hitch, line up the hitch pinhole, and slide in the hitch pin. With our hitch pin in, we'll move to the back of the shank where we'll tighten down the knobs, returning our bike rack to the vehicle.Now, that our bike rack is secured, we can go ahead and go ahead and go over a few clearance measurements. We have a ground clearance of 12 inches, and the closest part of the bike rack to the closest part of the vehicle is six inches. We've added about 26 inches to the overall length of our vehicle. We'll now go ahead and unfold the bike rack platform and open our cargo door.As you can see, we can easily gain access to our cargo area.

Thule Vertex 4 Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox, we'll be test fitting the Thule Vertex 4 Hitch Mounted Bike Carrier, part number TH9029. To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of our hitch. We'll line up the hitch pin holes, thread in our anti-rattle bolt, and tighten it down using a wrench. Now, we want to go over a handful of clearance measurements. We've got about 12 inches of ground clearance and about 4 inches of clearance between the closest part of the carrier and the closest part of the vehicle. Overall, we've added about 10 inches of length to the rear of our vehicle with the bike rack arms folded down.

Thule Parkway 2 Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox, we'll be test fitting the Thule Parkway 2 Hitch Mounted Bike Carrier, part number TH958. To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of the hitch. We'll line up our hitch pin hole, thread in our anti-rattle bolt, and tighten it down using a wrench. Next, we'll go over a handful of clearance measurements. We've got about 12 inches of ground clearance and about 2 inches of clearance between the closest part of the carrier and the closest part of the vehicle. Overall, we've added about 22 inches of length to the rear of the vehicle.

Thule Hitching Post Pro Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox, we'll be test fitting the Thule Hitching Post Pro Hitch Mounted Bike Carrier, part number TH934XTR. To mount this carrier to our vehicle, we'll insert the shank of the carrier into the receiver tube of our hitch. We'll line up the hitch pin hole, thread in our anti-rattle bolt, and tighten it down using a wrench. Next, we'll go over a handful of clearance measurements. We've got about 12 inches of ground clearance and about 5-1/2 inches between the closest part of the carrier and the closest part of the vehicle. Overall, we've added about 15 inches of length to the rear of the vehicle with the bike rack arms folded down.

Swagman XTC2 Wheel Mount Hitch Bike Rack Review - 2012 Chevrolet Equinox

Today on our 2012 Chevrolet Equinox, we'll be test fitting the Swagman XTC2 Hitch Mounted Bike Carrier, part number S64670. To mount our carrier to the vehicle, we'll insert the shank of the carrier into the receiver tube of the hitch. We'll line up the hitch pin holes, feed in our anti-rattle bolt, and tighten it down using a wrench. Next, we'll go over a handful of clearance measurements. We've got about 12-1/2 inches of ground clearance and about 4 inches of clearance between the closest part of the carrier and the closest part of the vehicle. Overall, we've added about 20 inches of length to the rear of the vehicle.

Yakima StickUp 2 Hitch Bike Rack Review - 2010 Chevrolet Equinox

Today on our 2010 Chevy Equinox well be test fitting the Yakima Stick-Up 2 Bike Carrier part number Y02420. To begin our test fit well slide the shank of the carrier into the opening of the hitch tube, align our threaded pin hole, well thread our anti-rattle bolt through the threaded pin hole and tighten with a wrench. Now, lets go over some clearance measurements to see how the carrier and this vehicle fit together. There is about 12-1/2 inches of ground clearance. The closest part of the vehicle to the closest part of the carrier is about 2-1/2 inches. Weve added about 12 inches to the overall length of the vehicle.

Thule Domestique Roof Bike Rack Review - 2011 Chevrolet Equinox

Today on our 2011 Chevy Equinox, we'll be test fitting the Thule Domestique Roof Mounted Bike Carrier, part number TH513. Now with our Thule roof rack system already assembled onto our vehicle, we'll set the carrier onto the load bars and we can use the Allen key to tighten them both down. In order to tighten down the front part of the carrier, you must remove the skewer first. It's important the carrier is perpendicular to the load bars and parallel to the vehicle to ensure that the brackets have the proper fit onto the load bars. Once you have the brackets tightened down and secured to the vehicle, we're now ready to load our bike. We'll undo the wheel strap at the rear and insert the skewer into the front of our bike rack.

RockyMounts TieRod Roof Bike Rack Review - 2011 Chevrolet Equinox

Today on our 2011 Chevy Equinox, we're going to be test fitting the RockyMounts TieRod Roof Mounted Bike Carrier, part number RKY1014. To install the carrier, set it on top of our load bars. Feed the straps at the head of the bike carrier around of the front bar, lock them back into the head, and use an Allen key to tighten them down. Now, it's time to reinstall the cover on the head of the bike rack. At the back, well use a clamp and we'll tighten it down by using the Allen key. Once we've done that, we're ready to load up our bike.

Yakima ForkLift Roof Mounted Bike Rack Review - 2013 Chevrolet Equinox

Today on our 2013 Chevrolet Equinox well be test fitting the Yakima Forklift Roof-mounted Bike Carrier, part number Y02098.Now, with our vehicle already equipped with a roof-rack, were ready to fit the forklift to the vehicle. Well place the bike rack on top of our crossbars and align the two mounts with our crossbars. Here on the front, well bring the head of the bike rack directly over the front crossbar and make sure that the clamp goes underneath.We can then use the wing nut to slide the bolt through the clamp and tighten it down. Well then slide the back of the head forward to lock the front wing nut in place. Well move to the back mount where well make sure that the clamp goes underneath the crossbar and tighten it down.Well then install our skewer. With the skewer in place and opened up ready for the fork of our bike, well make sure that our rear wheel strap is undone and out of the way.We can then place the bike into the bike rack making sure the front fork falls into the skewer.

RockyMounts PitchFork Roof Bike Rack Review - 2013 Chevrolet Equinox

Today on our 2013 Chevrolet Equinox well be test fitting the Rockymounts Pitchfork Roof-mounted Bike Carrier, part number RKY0438. Now, with our bike rack already preassembled and the vehicle already equipped with the roof rack system, were ready to fit the bike rack to the vehicle.Well place our bike rack on the crossbars making sure that the head of the bike rack is directly over our front crossbar. Well then take the clamp and secure it on the front of the head of the bike rack and bring it around underneath the crossbar. Well then tighten it down using the two Allen bolts inside the head of the bike rack. Well then move to the rear crossbar where well put the clamping device around the crossbar, run the bolt through from the bike rack and tighten it with the wing nut.Well then make sure that both our Allen bolts are tight as well as the wing nut here on the rear crossbar where we can then install our bike rack securely. With the securer in and opened up, well open up the rear bike rack strap for the rear wheel.