Curt Trailer Hitch Mounted Spare Tire Carrier

Curt Trailer Cargo Control - c31006

Trailer Hitch Mounted Universal Spare Tire Carrier by Curt

• Trailer hitch mounted spare tire carrier
• Universal spare tire carrier
• Compatible with 2" x 2" trailer hitch receivers
• Pin hole locations:
  • Hole closest to upright bar measures 5-1/2" from the center of hole to upright
  • Middle hole measures 7-1/2" from center to upright
  • Furthest hole from upright bar measures 9-1/2" from center to upright
• Measures 24-1/4" tall
• Durable, black powder coat finish resists corrosion
• Hardware not included

C31006 Trailer Hitch Universal Spare Tire Carrier by Curt

Customers Who Purchased This Trailer Cargo Control Also Bought...

Ask the Experts about this Curt Trailer Cargo Control
Do you have a question about this Trailer Cargo Control?

• What is the Height of the Curt Trailer Hitch Mounted Spare Tire Carrier I have 20 inch wheels
  
• I spoke with my contact at Curt and while we do not have a picture of the Spare tire rack, part # c31006, in use at this time she did send me a dimensional drawing of the carrier that I will send to you as an attachment in a separate email. The Height of the unit is 24 inches from the bottom of the receiver shank to the top of the carrier. From these measurements I believe the spare carrier will work for you. Along with the spare tire carrier you may want to consider the Anti-Rattle Device an
  view full answer...


• What is the Weight Handling Capacity of the Curt Trailer Hitch Mounted Spare Tire Carrier
  
• The Curt Trailer Hitch Mounted Spare Tire Carrier, item # c31006, does not have a weight capacity rating for the carrier itself. The carrier will be able to handle a wheel and tire combination as long as the weight of the wheel, tire, and carrier are within the tongue weight rating of the receiver hitch it is mounted in. If your hitch, front or rear, is rated for 350 pounds then that would be the maximum amount you could carry. You will have to supply 3 bolts and nuts (not included) to secure
  view full answer...


• Compatability of Full Size Wheel and Tire Mounting On the Curt Hitch Mounted Spare Tire Carrier
  
• I did some calculations and came up with a 6.78 inch tall sidewall on your tire that combined with the 9 inch Radius of your wheel would give you 15.78 inches above and below the center of the wheel mount location on the Curt Hitch Mounted Spare Tire Carrier, item # c31006. I went out to the warehouse and measured on the angle from the center of the tire mount and the distance back down to the support bar at 15.78 inches is 8 inches. This is why the angle is built into the item, so that the w
  view full answer...


• Dimension of the Curt Trailer Hitch Mounted Spare Tire Carrier, item # C31006
  
• The Height of the Curt Trailer Hitch Mounted Spare Tire Carrier, item # c31006, is 24 inches from the bottom of the receiver shank to the top of the carrier.
  view full answer...


• Will Curt Spare Tire Carrier Hold a 19.5 inch Spare on a Ford F-450 With Front Mount Hitch
  
• We have two front mount receivers available for a 2004 F-450 cab and chassis. They are Draw-Tite part # 65022 and Curt part # 31114. I have added links to these parts and their install instructions below. I did some geometry with your 8 on 9 inch lug pattern and the bolt holes should line up so that you can at least 2 bolts of the wheel attached to the carrier. Whether or not you will clear the grille or bumper of the truck will take some measurements once a front hitch is installed, but it l
  view full answer...


• Will The Curt Trailer Hitch Mounted Spare Tire Carrier Fit 2003 Ford E450 With 255/75R16 Tire
  
• I walked out to the warehouse and took some measurements on the Curt Trailer Hitch Mounted Spare Tire Carrier, part # C31006. I calculated the overall diameter of your wheel and tire to be 31 inches. I measured on center from 15-1/2 inches up following the angle of the wheel mount. Then, I measured out 6-1/2 inches from the top of the vertical measurement toward the rear of the vehicle, and then straight down, which was 2 inches from the rearmost hitch pin hole on part the spare tire carrier.
  view full answer...


• Availability of a Trailer Hitch Mount Towing Spare Tire Carrier or Dual Purpose Ball Mount
  
• None of the trailer hitch mounted spare tire carriers, like # C31006, are what is considered to be a towing carrier. However, what you could do is use a dual purpose ball mount like # D210 or # V75090. With either one of these ball mounts you would place the hitch mounted carrier in the receiver portion and tow with the ball mount portion. You will have to make sure that you do not exceed the tongue weight capacity of the hitch when using the ball mount and receiver portion at the same time. You
  view full answer...


• Bike and Spare Tire Carrier Recommendation for a 2002 Damon Daybreak RV
  
• There might be a way to put a bike rack and a spare tire on the back of your 2002 Damon Daybreak RV, but the Curt Trailer Cargo Control, part # C31006, is not designed or rated to have the additional weight of a bike rack and bicycles on it, so it would not be a good option to go that route. I would recommend you use the # C31006 to carry the spare tire and then use a Topline 2 Bike Carrier RV Ladder Mounted Bike Rack for Elliptical or Flat Steps, part # BR1200, if you have elliptical or flat
  view full answer...


• WIll 15x7 Rims with 33x10.5R15 Wheels and Tires fit on a Curt Spare Tire Carrier # C31006
  
• Yes, the spare tire of your 1997 TJ Wrangler that has a 33x10.50R15 tire size on a 15x7 ecco cast aluminum spoke rim with a bolt pattern of 5 inches on 4-1/2 inches will be able to mount to the Curt Trailer Hitch Mounted Spare Tire Carrier, part # C31006.
  view full answer...


• Will Curt Spare Tire Carrier Hold a 19.5 inch Spare for a Class A Monaco Monarch Motor Home
  
• There is not a set weight limit for this Curt Trailer Hitch Mounted Spare Tire Carrier, part # C31006. As long as the hitch that is on your Class A Monaco Monarch Motor Home has tongue weight capacities that are above the weight of the carrier and wheel that it would be carrying you would be fine in that regard. As long as you can get two bolts through the mounting plate of this # C31006 you would be able to secure your spare to the carrier. This carrier can accept a wide variety of bolt patt
  view full answer...


• What is the Weight Capacity of Trailer Hitch Mounted Spare Tire Carrier # C31006
  
• I spoke with my contact at CURT Manufacturing about hitch mounted spare tire carrier # C31006, and he stated that it will hold your 85lb spare, provided that the trailer hitch itself is also capable of supporting the combined weight of the spare and the carrier. Basically, the weight capacity of the carrier is whatever the tongue weight capacity of the trailer hitch is.
  view full answer...


• Is There a Weight Limit for the Curt Trailer Hitch Mounted Spare Tire Carrier # c31006
  
• I spoke with my contact at Curt Manufacturing about Hitch Mounted Spare Tire Carrier, # c31006. He stated that it will hold your spare provided that the trailer hitch on the front of your vehicle is also capable of supporting the combined weight of the spare and the carrier. He stated that basically the weight capacity of the carrier is whatever the tongue weight capacity of the trailer hitch is.
  view full answer...


• Can Curt Trailer Hitch Mounted Spare Tire Carrier, # c31006 Be Used with a 26 Inch Wheel
  
• The Curt Trailer Hitch Mounted Spare Tire Carrier, # c31006, is a universal fit item designed to fit as many size tire/wheels as possible. In order to determine if your 26 inch wheel will fit, I have taken some measurements and made some pictures for you to view. You can also get a piece of paper and draw a triangle on it that measures 6-1/2 inches across at the bottom and 7-1/4 inches long on each side. The top of the top most hole of the carrier is at the point of the triangle and the two e
  view full answer...


• Bolts Needed for Mounting a Spare Wheel and Tire to the CURT Hitch Mounted Spare Tire Carrier
  
• You would need to find grade 5 or harder bolts, nuts and washers that match the wheel stud diameter of your wheels to mount a spare wheel and tire to the CURT Trailer Hitch Mounted Spare Tire Carrier, # c31006. It would also help to use a nut that matches the lug nuts for your wheel so you do not need an additional wrench to remove the spare from the carrier. Most trailer wheels use a 1/2 inch diameter wheel stud, so 1/2 inch hardware would work well, check to be sure of the wheel stud size f
  view full answer...


• Will the Curt Trailer Hitch Mount Spare Tire Carrier Hold a 37 x 12.50 x 17 Spare Tire
  
• We have had one customer put a 33 inch diameter tire on the spare tire carrier, # c31006, but I have not yet heard of anyone putting on a 37. The carrier is a universal fit item. Basically, if you take a look at the mounting surface dimensions and pattern in the pictures I have provided and they will allow your tire to be mounted to it, it will fit on the carrier.
  view full answer...