Submersible, Under 80" LED Trailer Light Kit with 25' Wiring Harness

Optronics Trailer Lights - TLL9RK

Trailer kit with 2 stud mount, waterproof, LED tail lights; corrosion-resistant license-plate bracket; 25' wiring harness; stainless steel mounting hardware

Features:

• Red, submersible, LED trailer light kit with stud-mounted lights, license bracket, wiring harness and mounting hardware
  • 2 Red, waterproof, stud-mounted LED tail lights (STL6RS and STL7RS) for trailers less than 80"
    • Driver's-side light includes license illuminator
  • Great replacement for incandescent lights
    • No bulbs to replace
    • No brittle filaments
  • Corrosion-proof license-plate bracket
  • 25' Wiring harness with 4-pole connector
  • Stainless steel mounting hardware included
  • DOT approved
  • Lifetime warranty on LEDs

Packaged kit includes 2 LED stud-mount tail lights and a corrosion-proof license-plate bracket.

Contents: (1) STL6RS, (1) STL7RS, (1) license-plate bracket.

Equipped with a 25' wire harness and stainless steel mounting hardware.

TLL-9RK Optronics Waterproof, Under 80" LED Trailer Light Kit with 25' Wiring Harness, Stud Mount

Customers Who Purchased This Trailer Lights Also Bought...

Replacement parts available for this product

Ask the Experts about this Optronics Trailer Lights
Do you have a question about this Trailer Lights?

• Are the mounting screws stainless steel on the LED Trailer Light Kit, part # TLL9RK?
  
• Yes, the mounting hardware included with the Waterproof, Under 80 inch LED Trailer Light Kit with 25 foot Wiring Harness, part # TLL9RK, is stainless steel and corrosion-resistant.
  view full answer...


• Newly Installed Trailer Light Kit Not Working Behind a 1998 Ford F-150
  
• Which grounds did you check? There are at least 4 ground connections that you need to make sure are working. One at each of the lights, the ground wire that goes from the trailer frame to the trailer connector, and the ground that goes from the vehicle frame or body to the vehicle connector. Any of these grounds could be the culprit. Remember, paint and rust can insulate these ground connections so make sure the eye terminals have direct metal contact. If everything else is wired properly an
  view full answer...


• What is the Spacing of the Mounting Studs on Optronics Trailer Light Kit, # TLL-9RK
  
• The spacing on the mounting studs on the lights in the Waterproof, Under 80 inch LED Trailer Light Kit with 25 foot Wiring Harness, # TLL9RK, are 2 inches, center to center.
  view full answer...


• Need Trailer Wiring to Use on 2008 Toyota Corolla and Fold-Up Trailer Kit
  
• We have a custom fit vehicle wiring for your vehicle. I used the Fit Guide on the website and found that the wiring kit you need for your 2008 Toyota Corolla is the Curt Custom Fit Vehicle Wiring, part # 55542. This kit will wire into the vehicle wiring and allow you to connect your trailer to your 2009 Toyota Corolla. Yes, this custom fit wiring simply plugs into your factory wiring harness, it is a plug and play kit. When connecting the trailer wiring to your vehicle it is always a good
  view full answer...


• Are the Waterproof, Under 80 inch LED Trailer Lights TLL9RK Completely Sealed
  
• I went out to the warehouse and pulled the Waterproof, Under 80 inch LED Trailer Light Kit, item # TLL9RK, to see exactly what Optronics means by waterproof. Upon initial inspection the housing itself is not water tight. Water can access the housing through the hole that the wires enter the light through and there is a drain hole at the bottom of the light near the center of the front lens. I then removed the front and side lenses and found that the led light system is encased (sealed) in
  view full answer...


• Are All LED Lights Submersible For Use On Boat Trailer
  
• When selecting an LED light, if the description states it is waterproof or submersible then the light can be submersed in water. The item you selected, Waterproof, Under 80 Inch LED Trailer Light Kit with 25 Foot Wiring Harness, part # TLL9RK, has encased LED diodes. Water can enter the light lens but not the LED casing. There are also 2 holes that allow water to drain out of the lens. Part # TLL9RK are used for the rear trailer lights for running, turn, and brake lights. For sealed sidem
  view full answer...


• LED Trailer Light Kit # TLL9RK with Stainless Steel Mounting Bolts Recommendation for Salt Water
  
• This Submersible LED Trailer Light Kit with 25 foot Wiring Harness, part # TLL9RK, uses all stainless steel mounting hardware. The mounting hardware of this trailer light kit should work well in the saltwater conditions that you use your boat in.
  view full answer...


• Troubleshooting Dim Lighting of a LED Trailer Light Kit Optronics # TLL-9RK
  
• Since there are a lot of variable in this situation the first thing I would recommend is to try and narrow down the problem to either the truck or the trailer. In order to do this I would try hooking your Dodge Ram 2500 up to another trailer with trailer lights that are known to work and then test the tail light functions in that situation. Or, you could hook your trailer up to a friends truck that you know has functional trailer lights and see if the trailer lights still react the same way.
  view full answer...


• How Much Power do Optronics Trailer Lights, # TLL9RK, Draw
  
• On the Optronics Trailer Lights, # TLL9RK, there are 2 different tail light assemblies. The driver side which includes the license plate light, draws a max of 0.254 amps at 12.8 volts (brake/turn lights) and the running lights draw 0.112 amps at 12.8 volts. The passenger side light is a little different since it does not power a license plate light. It draws a max of 0.259 amps at 12.8 volts (brake/turn) and 0.062 amps at 12.8 volts for the running lights.
  view full answer...


• What is the Difference Between Submersible and Waterproof Trailer Tail Lights
  
• A submersible tail light can let water in, there is usually a hole at a low point so the water can drain out. A waterproof light should be sealed to keep out water. For either type, you would also want to seal out water where the tail light wiring splices into the trailer wiring. Shrink tubing works well for this. You can also wrap up connections with electrical tape like # BT66. Or you could use a combination of liquid electrical tape, # SWC50122, and regular electrical tape. Ideally, if
  view full answer...