LED Submersible Trailer Stop, Turn and Tail Light, 6-Function, 11 Diode, Right Hand

Optronics Trailer Lights - STL8RB

This is a multifunction LED stop, turn, and tail light. This versatile light serves six functions: stop, turn, tail, rear reflex, side marker, and side reflex. The main red light measures 4-3/4" square x 2-11/16" deep; the attached red marker light makes the total length 5-3/16". The molded plastic housing and durable lens provide all-weather protection against corrosion. This light has 11 light-emitting diodes which draw 0.259/.062 amps at 12.8 volts. The light features a screw-down, replaceable lens. The light is a universal mount with two studs on 2" centers. The three-wire design includes the lead wires for power and a ground wire for mounting to any surface.

Features:

• Red, square trailer light serves 6 functions for trailers less than 80" wide
  • Stop, Turn, Tail, Rear Reflex, Side Marker, and Side Reflex
• Submersible
• Corrosion resistant
• 11 LEDs (Light Emitting Diode)
• Replaceable lens
• Stud mounts on right side of trailer with two studs on 2" centers
• Wiring design contains lead wires and a ground to mount to all surfaces
• Dimensions: 5-3/16" L x 4-3/4" W x 2-11/16" D
• Light draws 0.259/.062 amps at 12,8 volts

Manufacturer Specifications

Universal stud-mount stop, turn and tail lights for trailers under 80". The 6-function: stop, turn, tail, rear reflex, side marker, and side reflex. All weather molded plastic housing and durable lens protect against corrosion. Features screw on, replaceable lens. Mounts on 2" centers, grounds through mounting studs.

STL-8RB STL-6RS Combination LED Tail Light for trailers under 80" wide - Red - 11 diode 0.259V/0.062A by Optronics, Inc.

Customers Who Purchased This Trailer Lights Also Bought...

Ask the Experts about this Optronics Trailer Lights
Do you have a question about this Trailer Lights?

• How Do I Convert My Incandescent Trailer Lights to LED Lights
  
• Yes, you just have to remove the old lights, match the wires and mount the new ones. Please note, that it is usually not a good idea to mix LEDs and incandescent lights, so if you have have side markers or other lights on the trailer, make sure you switch those to LEDs as well. Incandescent lights draw much more amperage than LEDs do, and if they pull that current through the LED fixtures, the LEDs will burn up. We have LED side markers and clearance lights like part # MCL36AB and part # MCL
  view full answer...


• Replacement Right Hand Side Taillight For Optronics Trailer Lights Part TLL9RK
  
• The Optronics Trailer Light, # STL8RB, is a universal right side light for the # TLL-9RK set. They have the same dimensions, functions, amperage draw, and diodes. So this light will work.
  view full answer...


• Not Getting Turn Signal Function When Using LED Bulbs On A Trailer
  
• LED bulbs have little resistance on their own, so when used with turn signals they can create a hyper flash situation, which is a fast flashing of the bulb. To determine if you will need a load-resistor kit like the Putco LED Light Bulb Load-Resistor Kit - Ceramic, # P230004C, you will install the bulbs and when the turn signals are activated, if the bulbs hyper flash you will need to install the load-resistor kit. This kit will prevent the turn signals from hyper flashing. You will need one kit
  view full answer...


• Troubleshooting 5th Wheel Trailer Clearance Lights Blinking with the Turn Signals
  
• When using the brake and turn signal at the same time, you are drawing more power then just with running lights. Since some of the LEDs blink, they may inadvertently be attached to the turn signal wire on the trailer. Most trailers have one wire that carries both turn signal and brake light functions and one wire that carries running lights. I would check to make sure the correct wire is run to the new clearance lights. An LED clearance light like # MC65RB will have two terminals or wires. One f
  view full answer...


• Can Trailer Tail Lights be Grounded to the Towing Vehicle Instead of the Trailer Frame
  
• When installing the LED Submersible Trailer Stop, Turn and Tail Light, # STL8RB, you will want to ground it to the trailer. Having a ground that is attached to the tow vehicle would be so long it could make the ground ineffective. Also, you would have to disconnect it every time you disconnected the trailer. The movement of the trailer could also pull the ground loose if it were attached to the tow vehicle. If corrosion is a problem, you will need to find the best place you can near the mounting
  view full answer...


• New Trailer Tail Lights Blow a Fuse and Cause Lights to Turn Off
  
• The LED Submersible Trailer Stop, Turn and Tail Light, # STL8RB, comes with one wire for turn and brake functions (green) one wire for tail lights (brown) and a white wire as the ground. The ground wire will need to be attached to a clean and corrosion free metal surface on the trailer. A lot of trailers have tail lights that ground through the mounting studs. These types of lights will also need to be attached to a clean and corrosion free metal surface. A bad or absent ground could be ca
  view full answer...


• Can a Passenger Side Tail Light Be Used on the Driver Side of a Trailer
  
• Left side tail lights have a clear lens on the bottom to light up the license plate. Right hand side tail lights do not. If you were to use the right hand side light, # STL8RB, you would need a separate light to illuminate the license plate. The left hand side light that matches is # STL9RB. If you click on the last picture on the product page, you will see the lens.
  view full answer...


• LED Marker Lights on Trailer Stopped Working After 5 Years
  
• Since you have checked the ground connection and tried a different grounding point. I would check to make sure the lights are getting power by using a circuit tester like part # 3808. You will want to inspect the power wires going to the the lights to make sure there is not any frayed or shorted wiring in the system. Then, I would inspect the vehicle and trailer side connector for corrosion. Corrosion in the connector could be causing a bad connection and preventing the lights from getting po
  view full answer...


• Troubleshooting Left Blinker Not Working on a Trailer
  
• It really sounds like the ground is not making good enough contact on the left turn signal/tail light and because of that it is able to draw enough amperage to illuminate the blinker function of your bulb. There is a chance the converter box of your setup could be wrong, in order to test that you will need to test for voltage coming into the box and then for voltage coming out of the box with circuit tester like part # 3808. If you find that there is voltage going into the box on the left tur
  view full answer...


• Troubleshooting Right Turn and Running Lights on Trailer Towed by 2007 Ford F150
  
• I would recommend starting at the 7-way connector at the rear bumper of your truck. Use a circuit tester like part # 40376, and activate the right turn signal. Test the pin in the 3:00 position. The tester should flash with the turn signals. When the brake pedal is pressed, this pin should light up the tester as well. Repeat the test on the pin in the 9:00 position which is the left turn/brake and the pin in the 11:00 position, which is the running/ marker lights. Check the pins for excessive
  view full answer...


• Trailer Lights Malfunction on 2007 Ford F-150 Towing a S and H Horse Trailer
  
• The first part of the problem sounds like a bad ground. A bad ground usually shows up when the system is under load. Start by checking the trailer and vehicle side connectors. Clean out any dirt or corrosion built up inside and in the backs of the connectors. Next check the ground on the vehicle side connector. It should be attached to a clean, bare metal surface on the vehicle frame. Also check the trailer side main ground. It should be attached to a clean, bare metal surface on the trailer
  view full answer...


• LED Tail Light STL8RB Used for Left Hand Application
  
• Because of the side marker light on the side of the lamp, Part # STL8RB should only be used for the right hand tail light. The left LED taillight would be part STL9RB.
  view full answer...