Redline Trailer Spindles - R50342EZ
Trailer Axle Spindle
| Part No. |
Capacity |
A |
B |
C |
D |
E |
F |
Round/Square |
| R50342EZ |
2600 lb |
2.25 |
2.24 |
1.74 |
1.25 |
1.00 |
3.00 |
Round - E-Z Lube and Flge |
Customers Who Purchased This Trailer Spindles Also Bought...
Ask the Experts about this Redline Trailer Spindles
Do you have a question about this Trailer Spindles?
- Spindle Replacement on 2006 Fleetwood Prowler Camper
- Replacing the spindle on your axle will require cutting the old spindle off and welding a new spindle (see link) in its place. You would need to find a certified welder so that he has the proper tools and welding equipment to make the repair. To figure out which spindle is correct for your trailer you can use the bearing part numbers, both inner and outer, axle weight capacity and the shape and length of the spindle stub on your trailer. The bearing numbers will let you cross reference the corre
view full answer...
- Which Hubs Fit the # R50342EZ Spindle
- If you need a 6 lug on 5.5 inch bolt pattern then you will need the following hubs.
8-213-5UC1-EZ 6 on 5.5 Idler Hub Bearings 25880 inner and 15123 outer
8-201-9UC3-EZ 6 on 5.5 Hub and Drum Bearings 25880 inner and 15123 outer
If you need a 8 lug on 6.5 inch bolt pattern then you will need the following hubs.
8-231-9UC1-EZ 8 on 6.5 Idler Hub Bearings 25880 inner and 14125A outer
8-219-4UC3-EZ 8 on 6.5 Hub and Drum Bearings 25880 inner and 14125A outer
view full answer...
- What Are Dimensions And Bolt Hole Spacing On Brake Flange On Redline EZ Lube Spindle, # R50342EZ,
- The picture on Redline EZ Lube Spindle 2.25 inch RD x 3 inch STUB, # R50342EZ, is a typical photo. Which means it might not be a picture of that exact part. I went out in our warehouse and pulled the actual part and took measurements.
The brake flange on the spindle is a square plate with rounded corners and has 5 bolts attached to the flange. If you set the spindle down on the flat edge of the brake flange that will allow the top bolt to be at the 12:00 position then the width of the brake f
view full answer...
- Will Redline EZ Lube Spindle, # R50342EZ Fit The Dexter Trailer Hub Assembly, # 8-201-9UC3-EZ
- The Redline EZ Lube Spindle 2.25 Inch RD x 3 Inch STUB, # R50342EZ will fit the Dexter Trailer Hub Assembly - 5200 & 6000 lbs - 6 on 5-1/2 - EZ Lube, # 8-201-9UC3-EZ.
The trailer hub assembly is a 6 on 5-1/2 inch bolt pattern and is rated at 3,000 lbs. per assembly.
view full answer...
- What Bearings Seals Brakes and Tires to Use for 4400 lb Axels on a 2004 Airstream 30 Feet Long
- I did a little research and found that the National Seal, 442109, has an inner diameter of 2.25 inches and an outer diameter of 3.376 inches. We carry two seals that can be used as a replacement for this seal. If your hubs have greased bearings you should use the TruRyde Grease Seal, item # 42385, and if your hubs have oil bath bearings or have E-Z lube spindles, you should use the TruRyde Grease Seals, item # RG06-070 (pair), which is a double lip seal.
Your inner bearing should match up wi
view full answer...
- What is the Correct Replacement Spindle for a 6,000 Pound Dexter Trailer Axle
- From the research I did, a 6,000 pound Dexter axle will take Spindle # R50342EZ, that you have referenced, or Spindle, # R50642. The difference between these 2 is that the R50342EZ is an E-Z lube with a 2,600 pound capacity and the R50642 is not an E-Z lube and has a 2,500 pound capacity.
He do have matching hubs for these spindles (hubs come with bearings, races, and seals) but the one thing they all have in common is that they all have a 6 on 5-1/2 bolt pattern. I could not find any 5 bolt
view full answer...
