Custom Fit Vehicle Wiring > Fifth Wheel and Gooseneck Wiring > No Converter > 7 Blade > Pollak

Custom Fit Vehicle Wiring Pollak PK11893-11932

Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole - Ford, GM, Nissan w/ Factory Plug

Rating: rating rating rating rating rating
21 reviews

Code: PK11893-11932

Retail:$107.98

Price:$54.95

Shipping Weight: 3 pounds

Shipping Special

Orders of $150 qualify for free shipping.
Lowest Price Pledge

Fifth Wheel and Gooseneck Wiring Harness - 2011 Chevrolet Silverado 2500 - Video
Fifth Wheel and Gooseneck Wiring Harness Installation - 2006 Ford F-350 - Video

Pollak Custom Fit Vehicle Wiring - PK11893-11932

This socket plugs into T-connector to provide a 7-pole trailer connector in the truck bed for use with fifth wheels. Connector plugs into OEM wiring harness to allow for a 7-pole connector in the truck bed.

Features:

7-Pole, sealed socket, RV-style trailer connector with T-connector
- Plugs into OEM harness - no splicing
- Provides quick and easy installation of RV socket in truck bed
High-impact nylon construction
- Resists corrosion
Spring-loaded lid with stainless steel spring and runner gasket
- Prevents intrusion of moisture when closed
- Has drain slot and angled design for drainage
- Includes wiring diagram for quick installation
Copper-plated terminal pins
- High conductivity and low resistance
- Sealed with silicone at the back of the socket
  - Prevents moisture from contacting mating connector

Specs:

Application: Chevy, GMC, Ford and Nissan trucks
Current rating: 30 amps
Volt rating: 12 volts
Length: 7-1/2 feet
1-Year limited warranty

11-893 and 11-932 Pollak 7-Way, RV-Style Trailer Connector Socket w/ 5th Wheel and Gooseneck T-Connector
Replaces 20110 and V30133

Video of Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole - Ford, GM, Nissan w/ Factory Plug

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Video 5th wheel wiring 2011 chevrolet silverado

Fifth Wheel and Gooseneck Wiring Harness - 2011 Chevrolet Silverado 2500

Video install fifth wheel wiring 2006 ford f350 pk11893 11932

Fifth Wheel and Gooseneck Wiring Harness Installation - 2006 Ford F-350

Video Transcript for Fifth Wheel and Gooseneck Wiring Harness - 2011 Chevrolet Silverado 2500

Today on this 2011 Chevrolet Silverado 2500 series we will be installing we will be installing the fifth wheel to gooseneck wiring harness from Pollak part number PK11893-11932. The 5th wheel wiring harness that we are going to be installing today actually comes in two separate pieces here. The one end has these two connected ports that are going to plug into the backside of our existing 7 pole on the truck. There are open pins here on the other end, what we are going to do is wire that into the connector, and that is what is going to mount inside the bed. :37

Then we have the 7-pole itself, once we have it wired up the wiring harness will plug right into the back of it. We are going to start off inside the bed. The first thing we are going to do is find a mounting point for our plug. When determining where we want to mount our plug, the first thing we need to make sure of is that we are going to be mounting it in a spot where there is enough depth behind it. It is a good idea to go underneath the vehicle and take a look at what space you have in between the bed and the body. Just behind the rear axle there is a space in between the bed and the fender well. So that is the spot in the bed that we are going to drill our hole. 1:13

The manufacturer actually recommends you have 5 inches in between the bed and the body. So now that we have determined where we are going to mount the plug we can go back in the bed and drill the holes out for it. The manufacturer recommends you use a 2-1/8ths inch drill bit to accommodate the size of the plug. With the hole drilled you may need to take a file and run it around the outside side of the drilled hole just to make sure there are not any sharp or abrasive areas that could damage the wires as we feed them through. Next we are going to take our wiring harness and feed the end with the two plugs on it through our hole down, underneath the vehicle. With that lead of wire fed through we will next go ahead and take the open end here and wire it in to the provided plug. If you take a look at the back of the connector itself, the individual holes here are numbered. We will do a quick overview of which wire goes into each numbered hole. 2:15

In position 1 we will be placing the Red wire. Position 2 will be the white wire. Position 3 will be the blue wire. Position 4 the green wire. Position 5 the black wire. Position 6 the brown wire. Position 7 the yellow wire. With that stated we can put the wires into the connector. If you look at the wires with the terminals on them, there is a shorter and longer leg. We want the shorter leg of the connector to face towards the inside, or middle of the plug. That will hold true for all the connectors. With all the wires seated into place we will next take the blue internal ring and seat that on. Then we will plug our 7-pole in. On the back side of the tab here there is a gray locking clip that we want to push all the way in. That will help hold the two piece together and keep them from releasing on their own. We will the plug into our hole and mount it into place. 3:30

With the plug mounted in the bed we can go out to the 7-pole at the rear of the vehicle next, take it out and unplug the back side of it so we can plug our harness in line. To remove, this connector is a twist and tighten. There is a small tab on the outboard side here. If you take a flat head screw driver and push that in and rotate the plug counter clockwise. On the backside it is a similar plug like we mounted in the bed of the truck. Take and press the tab at the top and separate the pieces. Then you want to locate our harness, route it to the spot, and plug it in line. With everything connected we want to put the plug back into position. You may want to do a quick check underneath the vehicle for excess wire that you have, and tie that up and out of the way. That will conclude the installation of wiring harness part number PK11893-11932.

Customers Who Purchased This Custom Fit Vehicle Wiring Also Bought...

Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot $1.00

Reese Quick-Install Custom Base Rails and Installation Kit for 5th Wheel Trailer Hitches $239.95

Lube Plate for Elite Series and Reese 5th Wheel Trailer Hitches - 12" Diameter $8.99

Reese 5th Wheel Trailer Hitch with Square Tube Slider - 16,000 lbs $717.95

Curt 10" Fifth Wheel Trailer Hitch Lube Plate $9.95

Customer Reviews - Write a review about this product

Pollak 5th Wheel / Gooseneck T-Connector with 7-Pole - Ford, GM, Nissan w/ Factory Plug - PK11893-11932

Average Customer Rating: rating rating rating rating rating 5.0 out of 5 stars (21 Customer Reviews)