Hopkins Plug-in Simple Brake Wiring Adapter - Toyota

Hopkins Accessories and Parts - HM47815

Why mess with wires and splicing, when you can plug it in? Designed to fit Hopkins Agility brake controllers, this wiring adapter will have you on your way in no time!

Features:

• Includes 2 plugs
  • 1 Plug is inserted into the back of the Hopkins Agility Brake Control Unit
  • 1 Plug is inserted into the factory-installed port under the dash
• Fits Hopkins Agility Trailer Brake Controller (HM47294)

Specs:

• Compatible with pre-wired Toyota and Lexus vehicles with a tow package
  • 2003-08 Toyota 4Runner
  • 2008 Toyota Land Cruiser
  • 2003-09 Toyota Sequoia
  • 2005-09 Toyota Tacoma
  • 2003-11 Toyota Tundra
  • 2004-08 Lexus GX470

You have a lot to think about when you are connecting a vehicle to a trailer or RV. Hopkins makes it easier with a vehicle-specific wiring adapter, designed to fit the Agility brake controller. Simply plug it in and go.

47815 Brake Control Connectors

Customers Who Purchased This Accessories and Parts Also Bought...

Ask the Experts about this Hopkins Accessories and Parts
Do you have a question about this Accessories and Parts?

• Installing Hopins Brake Force Brake Controller on 2010 Toyota Tundra
  
• The wiring harness remains the same for the 2010 model as the 2009. The HM47815 will be an exact plug in for you, assuming that your Tundra was equipped with the factory tow package with the 7-way trailer connector on the rear bumper. If you do not have the tow package, and have the 4-way connector only, you will have to hardwire the controller into the existing vehicle wiring. We offer a Brake Controller Installation Kit, part # ETBC7 for a 7-way connector or part # ETBC6. We have a brake
  view full answer...


• Will the Hopkins Plug-in Brake Wiring Adapter - Toyota Work with the Hopkins Impulse Controller
  
• Yes, the Hopkins Plug-in Simple Brake Wiring Adapter - Toyota, item # HM47815, will work with the Hopkins Impulse Brake Control, # 47235 and any plug in simple Hopkins electric brake controller. The # HM47815 harness is compatible with pre-wired Toyota and Lexus vehicles with a tow package.
  view full answer...


• What Wiring Is Needed For Hopkins Brake Controller, # HM47294, On A 2008 Toyota Tacoma
  
• On your 2008 Toyota Tacoma with no towing package you will need to install the Tow Ready Vehicle Wiring Harness, # 118496. It is a plug-in connector so there is no cutting or splicing required. This harness will plug into a connection located behind the vehicles taillights and will give you a 4-pole flat trailer connector at the rear of your vehicle. You will also need to hardwire your 2008 Toyota Tacoma for the brake controller by using the Brake Controller 7 & 4 Way Installation Kit, #
  view full answer...


• Installing Hopkins Brake Force Brake Controller on 2006 Saturn Vue
  
• The black connector on the end of part # HM47815 will work with your Brake Force controller. However, the white connector on the other end is designed to connect to various Toyota trucks and SUVs and will not plug into your Vue which does not have a connector under the dash for connecting a brake controller. The connector can still be used, but the white connector will need to be cut off. To install the controller in your Vue, it would need to be hardwired, using our Brake Controller Install
  view full answer...


• Parts Needed to Install a Brake Controller on a 2000 Toyota Tundra with Tow Package
  
• For a 2000 to 2002 Toyota Tundra, you will not be able to use the Hopkins Plug-in Simple Brake Wiring Adapter, # HM47815. As you have stated, it fits 2003 to 2011 models. Of the manufacturers we carry, none offer a brake controller wiring harness that will fit the 2000 Tundra. If the truck already has a 7-Way trailer connector, you will need to hardwire an installation kit for a brake controller using wire # 10-1-1, and a 20 or 30 amp circuit breaker (see brake controller instructions for wha
  view full answer...