Edge EZ for Dodge Cummins 5.9L, 24V

Edge Performance Chip - EZD1000A

The Edge EZ Module can be quickly installed to provide additonal horsepower and torque through easy power level adjustments

• Adds up to 65 Horsepower
• Adds up to 180 Foot Pounds of Torque
• Increases Fuel Economy
• Helps eliminate downshifting while towing
• Maximizes efficiency by monitoring the RPM, Timing, Turbo Boost Pressure, and Fueling Parameters
• Uses engine information to control and enhance timing and fueling
• Easy installation needs no mechanic labor, no drilling, and no computer downloads.
• Completely Weatherproof

The Cummins motor is one of the most powerful motors ever put in a pickup truck. The Edge EZ module unleashes the potential of this monster by carefully monitoring RPM, timing, turbo boost pressure and fueling parameters and adjusting fueling and timing to maximize power, torque, and driveability.

The Power Edge EZ is a plug-in module that maximizes engine efficiency by monitoring the RPM, timing, turbo boost pressure and fueling parameters. The module uses this information to determine and control both fueling and timing enhancements for the Bosch fuel injection pump. The re-mapping of the fueling and timing parameters is done via the CAN-BUS communication system. The CAN-BUS protocol is used to communicate between the Cummins Engine Control Module (ECM) and the Bosch fuel injection pump. All data sent from the EZ is within the limits of the Bosch fuel injection pump. This enables smooth and predictable power delivery without compromising integrity. This increase in power does not increase the exhaust smoke from a stock engine.

The Edge EZ allows maximum fueling at full turbo boost and provides an additional 65-rear wheel horsepower, an additional 180 foot pounds of torque and installs in minutes. Simply plug the EZ connectors into the ECM Data Link connection and MAP sensor. There's no need to unplug the Bosch fuel injection pump connector. The Edge EZ module is completely weatherproof and mounts easily under the hood.

The EZ can also be stacked with other upgrades to deliver even more power. There is not an upgrade on the market today that can deliver as much power and install so simply.

*Legal in California only for racing vehicles which may never be used upon a highway.

---

The connectors plug into the MAP sensor and Data Link connector.
	The included brass elbow permits turbo boost pressures of greater than 20 psi without the wastegate opening. The EZ module will operate equally well with or without this installed.

Edge Products # 30201

This Product Fits The Following Vehicles

2001 - 2001 Dodge Ram Pickup 5.9L, Cummins ISB

Ask the Experts about this Edge Performance Chip
Do you have a question about this Performance Chip?

• How to Change Levels on Edge EZ Programmer for 2001 Dodge Ram Cummins 5.9L, 24V
  
• The Edge EZ, # EZD1000A, is preset to level 3 of low boost fueling which is the most responsive. To change the settings you would use an allen wrench to remove the two screws on the front panel. On the other side of the panel you will see 3 jumper settings. The jumper should be positioned in the right most location unless it has been changed before. You can move the jumper once to the left for level 2 or all the way to the left for level 1. I have included a link to the installation instruction
  view full answer...


• Will Adding a Programmer to a 2001 Dodge Ram 5.9 Cummins Produce More Soot and Smoke
  
• The Edge EZ for Dodge Cummins 5.9L, 24V, # EZD1000A, is not a programmer that will allow you to make adjustments to allow more or less soot from the exhaust. What it will do is add horsepower and torque and it will also increase fuel economy and improve shifting. However, the addition of more power can also increase fuel consumption which will produce more soot on its own. I have included a link to the installation details for you. You are more likely to get more soot if you used a programmer
  view full answer...