etrailer Accessories and Parts - ETBC6
Installation Details
Includes all parts necessary to install an electric trailer brake controller in your vehicle.
Each kit includes:
- 25' of duplex wire in an abrasion resistant cover
- Pre-wired 6 and 4 way connector with mounting bracket
- 6-Way connector plugs into existing 4-way trailer connector on vehicle
- Heavy duty breakers
- (1) 20 amp, (1) 30 amp, (1) 40 amp (for hot lead)
- Ring connectors for battery and breaker hook-up
- Self-tapping screws
- Tie straps
NOTE: The blue wire goes to the center pin, the red wire goes to the outside pin. The 6 pole trailer connector can have the brakes or 12v power supply in either spot.
If your vehicle does not already have a flat 4-Pole installed, the T-One Fitguide can be used to find the easy to install connector made specific for your vehicle.
|
| A better view of the 6-way trailer connector.
|
Replaces 39506
Customers Who Purchased This Accessories and Parts Also Bought...
Ask the Experts about this etrailer Accessories and Parts
- Brake Controller and Installation Kit for a 1999 Ford Ranger
- To wire your 1999 Ford Ranger for a 6-way connector and a brake controller you will need a 4 way wiring harness for your vehicle, which you already have and a Brake Controller 6 & 4 Way Installation Kit, part number ETBC6, along with a brake controller you see link. You will attach your 4-Way wiring harness inline with the connector provided with the ETBC6 kit to power the taillight functions.
After this is done you will need to connect the brake wire and the accessory wires, which will be
view full answer...
- Parts for Adding a Brake Controller and 6 Pole Wiring to a 2002 Toyota Tundra
- Since you are wanting to add a brake controller, and you already have a working 4-Way connector, you can use our Brake Controller 6 way installation kit, # ETBC6 the 6 way connector would be included, as well as all needed wire and connectors.Your factory 4 way would plug right in to the 6 way.
We have detailed instructions for the brake controller installation kit and a video that will help with the installation, see links.
You did not mention which brake controller you were interested i
view full answer...
- Brake Controller Wiring Kit for a 2000 Dodge Dakota
- We have a 6-way or a 7-way brake control wiring kit that would work good for you. You can use the included adapter to upgrade the truck four pole to the 6 or 7-way and then leave the extra wires capped off and tied up out of the way until you are ready to install the brake controller. You can view these two kits using the following links.
6-way Brake Control Wiring Kit
7-way Brake Contol Wiring Kit
view full answer...
- What is Needed to Install a Brake Controller and 6-Way Trailer Connector on a 2008 Honda Pilot
- Since your trailer has a 6-Way connector installed you most likely have one of 3 wiring situations on your trailer. The first, and most likely, is that your trailer has electric brakes and a power wire to maintain a battery for auxiliary functions. The second is that you have the same power wire and backup lights at the rear of the trailer. The third, and least likely but possible, is that your trailer has hydraulic surge brakes and a coupler with electric backup lockout.
If your trailer has
view full answer...
- Is There a 6 and 4-Way Combo Connector Sold Separately
- Yes, we have an adapter that converts the 4 pole connector to a 6 and 4-way connector, it is Adapter 4 Pole to 6 Pole and 4 Pole Trailer Wiring Adapter, part 37175. If your vehicle currently has 4 pole wiring it will work perfectly on your 1998 Chevrolet C2FK Series Pickup Truck.
If you do not have a 4-way connector on your vehicle you would need the Tow Ready Custom Fit Vehicle Wiring, part # 118315, that will plug directly to your factory wiring.
view full answer...
- Using Part # ETBC6 to Install Brake Controller on 1999 Chevy Astro
- The 4 to 6-way trailer connector adapter supplied with the Brake Controller Installation Kit has a 4-pole connector that connects to the existing 4-pole on your Astro.
The remaining wires attach as follows:
The black wire provides 12-volt power for use by any trailer mounted accessories requiring a power feed. This wire would run to the positive battery terminal via the 40 amp inline breaker included in the kit.
The blue wire carries the output from the brake controller. It would run und
view full answer...
- Do I Need Brake Controller For 1999 Toyota Tacoma Towing 2500 lb Trailer w/ Electric Brakes
- If the Gross Trailer Weight (GTW) of the trailer you are towing is half or more of the tow vehicles Gross Vehicle Weight, it is recommended to use a brake controller. Most states even require that a brake controller be used. I would recommend installing a brake controller for braking power and certainly for safety.
Since your 1999 Tacoma has a 4-way and the trailer has a 6-way connector, to install a brake controller, you will need to use the Brake Controller 6 and 4 Way Installation Kit, par
view full answer...
