RV Bumper 2" Trailer Hitch Receiver

Curt Specialty Trailer Hitches - E-100

Curt RV Bumper Mount Trailer Hitch

• Has 2" square receiver opening, ideal for hitch accessories such as bike racks and cargo carriers
• Intended for use on 4" square channel bumpers on the rear of many RVs and towable campers
• Powder coat finish resists corrosion
• Includes mounting hardware
• Weight capacity: 3,500 lbs GTW / 350 lbs TW

Note: Never exceed your bumpers gross towing weight.

Customers Who Purchased This Specialty Trailer Hitches Also Bought...

Ask the Experts about this Curt Specialty Trailer Hitches
Do you have a question about this Specialty Trailer Hitches?

• Dimensions of The # E-100 Rv hitch
  
• The 2 inch RV Bumper hitch, part # E-100, is designed to fit around a 4 inch square tube bumper so you will not be required to drill into the bumper. I went out to the warehouse and measured the distance from the top of the receiver tube to the bottom of the mounting bolt hole and it is 4 inches. From the top of the receiver mounting tube to the top of the mounting bracket is 5 inches. You will have to measure to be sure that your bumper is 4 inches square and that there is clearance above the b
  view full answer...


• How to Determine the Compatibility of 2 RV Bumper Trailer Hitch Receiver E-100 With a Pop-Up Camper
  
• Yes, the Trailer Bumper Hitch Receiver, part # E-100, can be used on towable pop-up camper units with up to a 4 inch square bumper. However, you cannot exceed the limits of your camper bumper. The bumper towing and tongue capacities may be indicated on the bumper itself, but if not you could check your camper owner manual or contact the manufacturer of your camper. You can view some general information on towing and the rest of the RV bumper hitches we offer at the links provided.
  view full answer...


• Trailer Hitch for Towing a Trailer Behind a 2006 Rockwood by Forest River Travel Trailer
  
• I cannot make a recommendation for pulling a trailer behind another trailer. I know it is done, but there are many things to take into account when thinking about this endeavor. You will need to contact the trailer manufacturer to see if the bumper will have enough capacity to handle the loaded trailer weight and tongue weight. I am sure you will be told that it will not. You should also consider that sway can be a big problem when towing more than one trailer and proper loading of both trai
  view full answer...


• Will the Curt RV Bumper Hitch, Part E-100, Clear the Spare Tire Support on My RV
  
• The hitch pin of the RV Bumper Hitch, part # E-100 would fall approximately 1-1/2 inches behind the front face of the bumper. You will want to measure from that point out to where it will clear the spare tire support. Compare this measurement to the shank on your cargo carrier. If the distance from the pin hole on the cargo carrier shank to the closest edge of the basket is greater than the clearance measurement you made, you should be fine. Using an extension, like part # HE06 is possible. H
  view full answer...


• Will Curt RV Bumper Hitch with 2 Inch Receiver fit my North Trail by Heartland RV
  
• The Curt E-100 Trailer Hitch Receiver is meant to be used on 4 inch square channel bumpers. You will need to measure your bumper and check to see if it is 4 inches square. The maximum capacity of this hitch is 350 pounds tongue weight and 3,500 pounds gross towing weight. Check the owner manual of the trailer and see what the bumper capacity is. If it is less, you must abide by the lower number. Make sure whatever bike rack or cargo carrier you will be using is built for use on the back of
  view full answer...


• Curt Bumper Mounted Receiver Part # E-100 for Towing Small Boat Behind RV
  
• The Curt bumper mounted receiver part # E-100 will serve that purpose. The receiver itself provides a 3500 lb towing/ 350 lb tongue weight capacity. This assumes that the 4 inch bumper on your RV has sufficient capacity to safely tow the towing/tongue weight of your boat and trailer. I would recommend checking with the RV manufacturer regarding the capacity of the bumper if it is not mentioned in the owners manual.
  view full answer...


• Hitch for 2005 Chevy 26 Foot Motor Home With 2 Inch Receiver to Launch and Haul a Boat
  
• Yes, we offer several different bolt-on frame mounted hitches. There are several to choose from that are adjustable to fit many models of motor homes and can be adjusted to fit your chassis. The frame mounted hitch is recommended because you can adjust it to fit your motor home and is better for towing as opposed to the bumper receiver hitch, part # E-100 that you selected. You will want to check with the motor home manufacturer before using the # E-100 hitch to make sure the bumper is rated
  view full answer...


• Mounting Orientation of Curt RV Bumper 2 Inch Receiver Part E-100
  
• The Curt RV Bumper 2 Inch Receiver, part # E-100 is designed for a 4 inch square channel bumpers. The Receiver is designed to be attached so that the receiver is below the bumper. Although the receiver is rated at 3500 lbs towing and 350 lbs of tongue weight, you will need to check the RV owners manual for the capacity of the bumper. If the capacity of the bumper is less than 3500 lbs or 350 lb of tongue weight, you will need to abide by the lower rating.
  view full answer...


• Will RV Bumper Mount Trailer Hitch # E-100 Fit a 4 Inch by 2 Inch Bumper on a Trailer
  
• I do have a possible solution for adding a trailer hitch to your trailer but # E-100 will not fit because the bumper on your trailer needs to be 4 inches by 4 inches (100mm x 100mm). I recommend installing a frame mount trailer hitch, # 13703. This hitch can be welded or bolted to the frame of a trailer provided the trailer frame is 22 to 72 inches wide. If welding, the hitch should be installed by a qualified professional welder. I have included a link to the installation details for you to rev
  view full answer...


• Trailer Bumper Mount Bike Rack Recommendations for a Camper with Rear Mounted Spare Tire
  
• If your bumper is rated for towing and/or carrying weight, we offer several bike rack options that are rated for use behind a trailer or RV. Take a look at the Swagman Around the Spare Mighty Rack, # S80500. This rack is designed to fit a 4 to 4-1/2 inch continuous welded square bumper and fit around the spare tire. I have included a link to the installation details for reference. Another option is the RV Bumper 2 Bike Rack, # S80605, or Swagman 4 Bike Carrier RV Mounted Bike Rack, # S80600.
  view full answer...


• Availability Of A RV Bumper Hitch That Will Fit A 4-1/8 Inch Square Rear Bumper
  
• On the CURT RV Bumper 2 Inch Hitch, part # E-100, the measurement from the top of the receiver tube to the bottom of the mounting bolt hole is 4 inches. The holes in the hitch that the mounting bolts goes through are not elongated, so there is no extra room for the bolts to allow an extra 1/8 inch extra clearance. I do have the Valley Universal RV Bumper Hitch, part # V75300 that should work for your application. This hitch will install with U-bolts that can fit around square bumpers up to 5
  view full answer...


• Trailer Hitch Recommendation for a Passport Trailer
  
• The Curt RV Bumper, # E-100, is designed to fit on a 4 inch square channel bumper. If this is the type of bumper you have, then the hitch will fit. You will want to check your RV owners manual to determine if he bumper is rated for this type of application and if so, what its capacity is. If you determine this hitch will not work, I recommend installing a frame mounted hitch, # 13703. This hitch fits box frames, C-channel frames, and I-frames that are 22 inches to 72 inches wide. I have inclu
  view full answer...


• Trailer Hitch Recommendation for Use on the Back of a Crossroads 5th Wheel Trailer
  
• We have a couple of different options in terms of trailer hitches for 5th wheel trailers. The Curt Hitch, # E-100, that you have referenced is designed to fit on 4 inch square channel bumpers. You will need to check to see if your bumper fits this description and if it is rated for this application. I recommend going with a frame mount hitch. The most versatile frame mount hitch we offer is Curt Hitch, # 13703. It can be bolted or welded on and fits C-channel, I-beam, and Box frames. Any weld
  view full answer...


• Availability of a Bumper Mount Cargo Carrier for the Rear of a Trailer
  
• We do not carry any cargo carriers specifically designed for use on the back of a trailer. Assuming that the bumper has the proper weight capacity, you could use a Bumper Mount Receiver, part number # E-100 in conjunction with a receiver mounted cargo carrier. A few of the railed cargo carriers we offer would be ideal for this application. I'll include links for the Bumper Mount Receivers and Railed Cargo Carriers below.
  view full answer...


• Will Part Number E-100, 2 inch RV Bumper hitch Fit on the Bumper of My RV
  
• The 2 inch RV Bumper hitch, part # E-100, is designed to fit around a 4 inch square tube bumper. I went out to the warehouse and measured the distance from the top of the reciever tube to the bottom of the mounting bolt hole and it is indeed 4 inches. From the top of the receiver mounting tube to the top of the mounting bracket is 5 inches. You will have to measure to be sure that your bumper is 4 inches square and that there is clearance above the bumper for the hitch to mount.
  view full answer...