Accessories and Parts > Trailer Lights > Replacement Parts > Mount Parts > Mounting Brackets > Black > Optronics

Trailer Light Mounting Bracket for 6-1/2" Oval Trailer Lights, Steel - Black Powder Coat

Rating: rating rating rating rating rating
27 reviews

Code: BK70BB

Price:$3.25

Shipping Weight: 0.5 pounds

Shipping Special

Orders of $150 qualify for free shipping.
Lowest Price Pledge

Quantity:

Oval Amber Directional LED Warning Lights Review - Video

Optronics Accessories and Parts - BK70BB

Trailer Light Mounting Bracket for 6-1/2" Oval Trailer Lights, Steel - Black Powder Coat

A black, steel bracket for mounting 6-1/2" oval lights. The bracket measures 8-1/4" long x 4" wide with a 1-5/8" deep mounting base. The bracket has a 6-11/16" long x 2-5/8" wide hole in the center for mounting the light, and has two screw holes in the bracket centered at the rounded ends of the hole. The black, powder coated bracket is made from sturdy, durable steel and can be used to mount lights vertically or horizontally. The bracket base mounts on 6-1/4" centers. Along with the sealed light, a grommet (A70GB) is required to complete the installation.

Black, powder coated bracket for mounting 6-1/2" oval lights
Constructed from strong, durable steel
Mounts lights vertically or horizontally
Lights mount into 6-11/16" long x 2-5/8" wide hole in center of bracket with screw holes centered at rounded ends
Base mounts on 6-1/4" centers
Requires grommet A70GB to complete installation
Dimensions: 8-1/4" L x 4" W with 1-5/8" deep base

Manufacturer Cross Reference
Bracket will work as an exact replacement for:
Uni Bond # MB2238
Truck Lite # 60720
Grote # 43362
Peterson # 421-09

Manufacturer Specifications

Black powder coated steel bracket for horizontal or vertical mounting of 6" oval lights. Grommet part #A70GB is required for complete installation.

BK-70BB Black Powder Coated Bracket for 70 Series Oval Lights by Optronics, Inc.

Video of Trailer Light Mounting Bracket for 6-1/2" Oval Trailer Lights, Steel - Black Powder Coat

Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Video Review Optronics amber LED warning light

Oval Amber Directional LED Warning Lights Review

Video Transcript for Oval Amber Directional LED Warning Lights Review

Today we are going to show you the amber flashing hazard lights from Optronics, part number SLL72AB1 and part number SLL72AB2. The flashing hazard lights are designed to be used on emergency, road-side assistance, construction sites and off-road vehicles, along with the rubber grommets, part number A70GB and the straight 3-wire pigtails, part number A45PB. They fit the standardized 6-1/2 inch oval shaped trailer light mounting holes, using the rubber grommets. There are 24 amber LEDs covered by a lifetime warranty. The lights are designed to fit inside the grommets that will hold them snug inside your mounting points. The rubber grommets simply stretch over the lights. On the reverse side of the light there is a port for the pigtail harness. The pigtail harness just fits into the posts and pushes in snug. The wiring for your light is already done at this point. All you have to do is connect the loose ends to the vehicle. 1:03

Once we have our light assemblies put together, we can go ahead and mount them inside our light brackets. Thanks to the grommet mounting design, all you have to do is push the light into place. With our lights in position, we can go ahead and begin the wiring process. The black wires are our synch wires. They allow the circuitry inside the two lights to communicate with each other so that we can get our flashing synchronized or alternating, depending on the lights we are using. We are using two type one lights, indicated by the 001 markings on the back of the light. Since these are both type one, they should flash together when we wire them up. The white wires are our ground wires. All you need to do is use an existing ground point on your vehicle and attach the eye terminals from the ground wires. The red wires are our powder wires. You can wire them to a 12 volt accessory circuit so that they are on whenever the vehicle is on or you can wire them to a switch power source so that you can manually control when the lights come on. We have a 12 volt DC power supply with us and we are going to take our two ground wires and connect them to the ground wire lead on our power source. Now, our black wires are already connected 2:27.

We are going to take our two power wires and twist them together. Once we attach them to our 12 volt power source, the lights should begin flashing in synch with each other. Thanks to the 24 LEDs in each light, they are plenty bright so that everybody will notice when these lights are flashing. Now we are going to switch out one of the lights. We will have a type one over here and a type two over here. When you mix and match the two types, the result will be an alternating strobe. We are going to take our two power wires and connect them to our 12 volt power lead off of our power supply. These lights should not be used on a cargo carrier or trailer that is used on normal roads. And there you have it for the Optronics flashing hazard lights, part number SLL72AB1 and part number SLL72AB2.

Customers compare BK70BB to these similar products