Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.

Rating: 




17 reviews
Code: 87435
Retail:$225.00
Price:$144.95
Shipping Weight: 26 pounds
Shipping Special
This durable, fully welded vehicle trailer hitch receiver features a powder coat finish over an e-coat base to ensure superior corrosion resistance.
Features:
Specs:
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Video of Hidden Hitch Trailer Hitch Receiver - Custom Fit - Class III - 2"
Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.
Today on this 2010 Buick Enclave we are going to be installing Draw-Tite hitch part number 75528. This installation will also apply to Hidden Hitch part number 87435. We are looking at the underside of the vehicle. On this Enclave you can see we have this fascia door covering. We want to remove that. There are two screws here on the bottom holding it in. Then we can just set it off to the side. :26
The next thing we want to do is go ahead and lower down our exhaust to give us more room to gain access to the frame. This particular model has duel exhaust so we are going to need to lower both sides down. There are two sets of hangers per side that we need to remove the exhaust off of. To lower the exhaust down off its hangers we need to take a spray lubricant, like a WD-40 and spray the studs down. Then we can take a pair of pliers or a pry bar and separate the two pieces. We will repeat that for the outboard side one as well. :56
We are going to repeat the same thing for the driver side exhaust as well. Before we take those down off the hangers we want to go ahead and support the main cross tube of the exhaust system because once we lower it off of both sides the system is going to want to fall if it is not properly supported it could damage it. With the exhaust lowered we can go ahead and point out the mounting holes we are going to be using to install our trailer hitch. Starting over on the driver side, you can see we have two existing weld nuts here at the bottom of the frame. These are going to provide our two attaching points for the driver side. That is going to be the same on the passenger side as well. Into those weld nuts we are going to be mounting the 12 millimeter bolts along with the conical tooth washers. Moving on to the center of the vehicle we have two attaching points here as well just behind the fascia door that we had removed earlier. To use these mounting holes we are going to be using the handle nut assembly along with the 1/2 inch hex bolt and conical tooth washer. What we are going to do with the handle nut is feed it through the square hole and lay it inside the frame over the attaching hole. What we are going to do is take and bend it so it sits like so right over the hole. When we put the hitch up we will put our hex bolt into place. We want to do that for both of the holes. 2:07
Now that we have all the mounting holes pointed out we can put our hitch up into position. Before I put the hex bolt into the handle nut here, we do need to put a small spacer in between the hitch and the frame. Now that we have all the bolts into place and snugged down, we are going to go back through and torque each one of the bolts down. You want to check with the directions to verify the appropriate torque rating for each individual bolt. Once we have all the bolts torqued down we want to put the exhaust back up on its hangers. Make sure we remove our safety strap when we are done. And then if you would like, you can take and bend the handle nuts up out of the way so they are not visible. Now our installation is complete. 3:24
Now that we have our hitch installed, we are going to give you a couple final installed dimensions, which will help make choosing your hitch accessories a little easier. From the top of the receiver tube opening to the ground is going to measure 17-3/4 inches. From the center of the pin hole to the clear the rear edge of the bumper is approximately 5 inches. This will conclude the installation of Draw-Tite hitch part number 75528 on a 2010 Buick Enclave.
2007 - 2012 GMC Acadia All Models
2008 - 2012 Buick Enclave All Models
2007 - 2010 Saturn Outlook All Models
2009 - 2012 Chevrolet Traverse All Models
Customers Who Purchased This Trailer Hitch Also Bought...
Average Customer Rating: 



5.0 out of 5 stars (17 Customer Reviews)




by: jeff07/24/2011
Is this review helpful?
this hitch is awesome. sturdy, easy to install, and not obtrusive at all. I like it a lot.20119




by: Danny w02/01/2012
Is this review helpful?
This product fit great and is easy to i nstall 30823




by: Jimmy S.08/15/2011
Is this review helpful?
The hitch installed on my Outlook. 21966




by: JR07/28/2011
Is this review helpful?
Perfect size and fits great. Quick delivery by UPS. 20533




by: Drew L Platts07/06/2011
Is this review helpful?
Worked perfect! 18680




by: John C.04/26/2011
Is this review helpful?
I had a great experience with etrailer.com...to the point that I could not resist writing a positive review. I was acutally suprised to see the huge box sitting on the front steps. I ordered a hitch, wiring harness & ball mount. One box - and all contents were taped together to avoid damage. Very satisfied - Thanks very much!12357




by: Pat F03/10/2011
Is this review helpful?
The hitch was very easy to install and fit without any problems. The trailer wiring also had great instructions which made for an easy install.8972




by: Vic J03/06/2011
Is this review helpful?
Very easy to install on 2011 Chevy Traverse. Hitch fit perfect and clears all installed equipment. Wiring harness easy to install. 1 hour total to install hitch and harness. eTrailer sells a good product. Highly recommend.8609




by: Vic J03/02/2011
Is this review helpful?
Recieved in excellent condition. Very fast shipping. Product packed great. Good information on website on installation. etrailer.com good company to do business with, highly recommend. 8252




by: Erwin G08/26/2010
Is this review helpful?
Extremely Happy Great product, easy to install & online installation videos were a big help3389




by: Don T.05/15/2010
Is this review helpful?
Very easy to install. I've installed several hitches over the years. This was by far the easiest to install. It is well designed, fit perfectly and was quick to bolt up. It took longer to wire the lights than put the hitch on.3033




by: Paul05/09/2010
Is this review helpful?
Great product. Installs easy. This is a great product and very well built. Standard delivery was very quick. Installation on an 2010 Acadia was quite easy and the site provided video installation helps very much. Even you don’t need to lower the exhaust, just push the mufflers to the exterior one by one and force the hitch into the location. I also ordered the wiring but I did not install it yet as I am primarily using the hitch for a bike rack. 3017




by: Terry07/15/2009
Is this review helpful?
Extremely easy to install. I had the hitch and wiring harness installed in less than 45 mins. The installation videos on your website were very detailed and helpful. Service and ship time were excellent.2133




by: rkt05/14/2009
Is this review helpful?
great hitch very easy to install, looks and works great1849




by: Clif04/28/2009
Is this review helpful?
Easy to install but has a flaw The square hole was made too large. When you install the ball adapter, it has too much play on the receiver that it makes a loud clunking noise. I would rather pay a little more for peace and quite when hauling my trailer and not have it sound like it's going to fall off.1798




by: David06/20/2008
Is this review helpful?
perfect fit, easy installation Product looks good, fits perfectly and was a breeze to install984




by: Ray09/17/2007
Is this review helpful?
Half hour to install Used existing holes in the frame for installation.Included all bolts washers and spacers with the hitch package.415
Ask the Experts about this Hidden Hitch Trailer Hitch
Do you have a question about this Trailer Hitch?