Hidden Hitch Trailer Hitch Receiver - Custom Fit - Class III - 2"

Hidden Hitch Trailer Hitch - 87424

This durable, fully welded vehicle trailer hitch receiver features a powder coat finish over an e-coat base to ensure superior corrosion resistance.

Features:

• Custom fit is designed specifically for your vehicle
• Computer-aided, fully welded steel construction ensures strength and durability
• Easy, bolt-on installation - no welding required
  • Complete hardware kit and installation instructions included
• Lifetime technical support from the experts at etrailer.com
• Black powder coat finish covers e-coat base for superior rust protection
• Ball mount, pin and clip sold separately
• Made in USA

Specs:

• Receiver opening: 2" x 2"
• Rating: Class III
  • Maximum gross trailer weight: 3,500 lbs
    • Maximum GTW when used with weight distribution: 4,000 lbs
  • Maximum tongue weight: 350 lbs
    • Maximum TW when used with weight distribution: 400 lbs
• Limited lifetime warranty

etrailer.com Technical Support

At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.

87424 Hidden Hitch Class 3 Trailer Hitch Receiver

Video of Hidden Hitch Trailer Hitch Receiver - Custom Fit - Class III - 2"

This Product Fits The Following Vehicles

2007 - 2012 Jeep Wrangler

2007 - 2012 Jeep Wrangler Unlimited

Customers Who Purchased This Trailer Hitch Also Bought...

Ask the Experts about this Hidden Hitch Trailer Hitch
Do you have a question about this Trailer Hitch?

• Installing a Class III Hitch on a 2008 Jeep Wrangler Does Not Require Drilling
  
• No, you will not need to drill any holes in the frame of your 2008 Jeep Wrangler to install the Hidden Hitch Class III hitch, item # 87424. Pretty much, you are going to lower your exhaust (if required), raise the hitch into position, install the fasteners, and then raise the exhaust again. Below is a link to the installation instructions for your review.
  view full answer...


• Will a Bike Rack Clear the Spare Tire with Trailer Hitch # 87424 Installed on a Jeep Wrangler
  
• Without the Hidden Hitch, # 87424 installed on your Jeep Wrangler, it is difficult to say exactly how much distance you will need to clear the spare tire. However, if you measure from the back of the crossmember out 4-3/8 inches, that is where the center of the hitch pin hole will be with the hitch installed. You can then measure out from that point to the distance needed to clear the spare tire, That distance is how much clearance a bike rack would need to have to clear the spare tire. I would
  view full answer...


• Will Hidden Hitch # 87424 Fit A 2008 Jeep Wrangler Unlimited With A Factory Tow Hook
  
• The Hidden Hitch Class III 2 Inch Hitch,# 87424, will fit a 2008 Jeep Wrangler Unlimited without the factory tow hook. It will use the four factory holes on the rear crossmember. So the factory tow hook does have to be permanently removed for the hitch to be installed on your vehicle. All of the hitches I have that fit your vehicle will install the same way, so to put a hitch on your 2008 Jeep Wrangler Unlimited you will have to remove the factory tow hook. I am sending a link to the inst
  view full answer...