Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.
Rating: 
4 reviews
Code: 75151
Retail:$156.07
Price:$116.95
Shipping Weight: 16 pounds
Shipping SpecialFully welded vehicle trailer hitch is strong and durable. Draw-Tite's Tested Tough guarantee ensures that this hitch exceeds industry standards. The combination of an e-coat base and a powder coat finish provides excellent rust protection.
Features:
Specs:
Draw-Tite's Tested Tough program provides testing standards far superior to those outlined by the Society of Automotive Engineers (SAE), the go-to source for engineering professionals.
Each Draw-Tite trailer hitch receiver undergoes extensive fatigue testing and static testing with the ball mount that is either supplied or recommended for use with that particular hitch, thus ensuring results that are applicable to real life use. Fatigue testing is also conducted on hitches rated for use with weight-distribution systems.
In addition, Draw-Tite performs static testing on a simulated automobile, as opposed to the rigid fixture used for SAE testing, resulting in a more true-to-life scenario.
At etrailer.com we're committed to the products we sell, and to our customers. Our experienced and knowledgeable staff are available via both phone and email to address your questions and concerns for the lifetime of your hitch. The technicians at etrailer perform hitch installations on a daily basis, making them a valuable resource for do-it-yourselfers. The one-on-one, personal service you'll receive comes straight from an expert in the towing and automotive field. We've installed it, we've wired it and we've towed with it, so whatever your question, we can answer it.
Video of Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
Videos are provided as a guide only. Refer to manufacturer
installation instructions and specs for complete information.
Today we are going to install part number 75151 from Draw Tite. We will install this on a 2006 Dodge Ram full size pickup. First step involves in some models you might have to lower the spare tire. If you have enough clearance between the bumper so you should not have to lower it. The next step is to go ahead and lower the plastic plate here. There are 4 tabs in the bottom you squeeze so you can flip this up out of the way. To remove the plastic piece these 2 tabs have to be squeezed on the bottom and pushed upwards. Next we install our hardware into the bumper itself. We just a carriage bolt in and the edges will ride in these little holes here a little bit. It kind of sticks up you can see it rock a little bit. We you tighten it down it will pull flush into it.
You can go ahead and install our hitch hanging from these 2 bolts. Next all we have to do is fish wire the bolts into the bumper and pull them out of the back pointing that way. We will go ahead and leave this loose so we can go ahead and have some wiggle room for the bolts to come through. We ran our fish wire into the frame here and what we are going to do is pull it up and through the side of the frame. Make sure you slide your plate on the wire first and then go ahead and thread on your bolt. Pull everything right on through and there you have it. At this point make sure you do not lose the bolt in the frame. Go ahead and repeat for the other side. Once you have all your hardware installed you can go ahead and move it a little bit. Try and get it as center as possible then go ahead and snug down the bolts. After that we can give the bolts their final torque. As you tighten these down you can see the bolt sink into the bumper. Now we can pop our plastic plate back on. That covers it for part number 75151 from Draw Tite.
2004 - 2005 Dodge Ram Pickup 1500 Series
2003 - 2003 Dodge Ram Pickup 1500 Series, built After 11/1/02
2006 - 2008 Dodge Ram Pickup 1500 Series, except Mega Cab
2006 - 2008 Dodge Ram Pickup 1500 Series, Mega Cab only
2003 - 2009 Dodge Ram Pickup 2500 and 3500 Series
Customers Who Purchased This Trailer Hitch Also Bought...
Average Customer Rating: 5.0 out of 5 stars (4 Customer Reviews)
by: A. Nonymuss05/04/2011
Is this review helpful?
Ordered this class 3 Draw-Tite for my '04 Ram. Absolutely perfect fit. Installation was no problem...took about 45 minutes. Would've gone faster, but I didn't have a 15/16" socket...had to use adjustable wrenches. Shipping was fast. 12851
by: Kyle D.12/06/2008
Is this review helpful?
Simple Install After watching the video here online, from backing the truck up to putting the tools away- just 22 mins. taking my time! Very easy install on a 2007 Ram 1500. High Quality, Heavy Duty.1454
by: rick11/09/2008
Is this review helpful?
the easiest install ever this product was so easy to install, who ever came up with that pull wire is a genius. it looks great and functions great as well.1415
by: Richard05/31/2008
Is this review helpful?
Better than Factory As with many products we all wonder will it match up to the description and the ease of instalation.... WELL THIS ONE DOES!! If you put a Dodge sticker on it, you would think it was a full factory instalation. Had the hitch installed in less than 30 minutes and everyting put up. Excellent product!!!!!!925
Ask the Experts about this Draw-Tite Trailer Hitch
Do you have a question about this Trailer Hitch?
Installation Details
