Weight Distribution 350 Mini for Fleetwood and Jayco Trailers with Swing-Up Jacks

Reese Weight Distribution - 66041

What do you do when you just want to throw the kids in the car and head off camping for the weekend but you dread the thought of sharing the road with big trucks? You know your trailer is going to sway! We have the solution so you and the whole family can enjoy these jaunts as much as you should.

This mini weight distribution system is designed for use with the lighter weight trailers and fold-down campers, especially for Fleetwood/Coleman trailers that have a side mounted swing away jack.

• Does not require snap-up brackets
• Works with any 2" receiver hitch
• Designed for tongue weights 100 - 350 lbs
• Maximum towing weight: 3,500 lbs
• Has 2" hitch ball, adjustable hitch bar, spring bars, pins and wear pads
• Works with trailer frames up to 4" tall
  • Trailers with frames smaller than 4" will need a spacer to hold the U-bolt straight.
• Shank can be used in either rise or drop position
• Designed for use with Fleetwood, Coleman and Jayco trailers with a side-mounted swing away jack

The Spring Bar mounts on "A" frame of trailer 28" back from center line of ball.

Customers Who Purchased This Weight Distribution Also Bought...

Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot $0.89

Tekonsha PRODIGY Brake Controller - Proportional $98.95

10 Gauge Blue Primary Wire - per foot $0.50

Brake Controller 7 & 4 Way Installation Kit - 10 Gauge $49.95

20 amp. In-Line Circuit Breaker $3.34

Reese Weight Distribution Reviews

Ask the Experts about this Reese Weight Distribution
Do you have a question about this Weight Distribution?

• 350 Mini Weight Distribution for Fleetwood and Jayco Trailers
• I'd recommend the 350 Mini WD for Fleetwood and Jayco weight distribution system. This unit combines weight distribution with sway control, and it w   view full answer...
• Can the Weight Distribution 350 Mini for Fleetwood and Jayco Trailers be Used in the Drop Position
• I spoke to my contact at Reese and he confirmed that you can use the weight distribution shank included in the 350 Mini # 66041 in the drop position. If it is still not low enough you can use the    view full answer...
• Compatability of Weight Distribution System for 2009 Toyota Tacoma Pulling a 2008 Bayside Trailer
• You are on the right track. A weight distribution system will transfer the load to your vehicle and trailer axles and level out the load. The weight distribution system you will need will depend o   view full answer...
• Should Torsion Bars Be Able to Fall Off My Weight Distribution Head Assembly
• The trunnion bars on your weight distribution system should not fall out of the head assembly when driving down the road or during normal turns. When backing the trailer or turning very sharply the ba   view full answer...
• Weight Distribution Kit Recommendation for a 2009 Jeep Wrangler Unlimited
• When towing a Tent trailer that is close to the vehicles rated capacity a weight distribution system is a good idea. The weight distribution system will transfer the weight from the trailer tongue to    view full answer...
• Weight Distribution System for a 2007 Honda Odyessey Pulling a Chalet Arrowhead
• You will need to do some measuring to determine if the 350 Mini will work on your trailer or not. The brackets that the spring bars set is will need to be installed at 28 inches from the center of the   view full answer...
• Which 350 Mini Weight Distribution Kit Should I Use With A 2008 Jayco 1207 and 2009 Honda Odyessey
• If your Jayco trailer has the Swing up jack on the outside of the trailer A-frame then you will need the 66041, 350 Mini for Fleetwood and Jayco Trailers with Swing-Up Jacks. If your trailer has the j   view full answer...